scholarly journals Aerodynamic Characteristics of Different Airfoils under Varied Turbulence Intensities at Low Reynolds Numbers

2020 ◽  
Vol 10 (5) ◽  
pp. 1706 ◽  
Author(s):  
Yang Zhang ◽  
Zhou Zhou ◽  
Kelei Wang ◽  
Xu Li
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Flow Separation ◽  
Numerical Study ◽  
Reynolds Numbers ◽  
Jet Flow ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
Low Reynolds Numbers ◽  
Low Reynolds

A numerical study was conducted on the influence of turbulence intensity and Reynolds number on the mean topology and transition characteristics of flow separation to provide better understanding of the unsteady jet flow of turboelectric distributed propulsion (TeDP) aircraft. By solving unsteady Reynolds averaged Navier-Stokes (URANS) equation based on C-type structural mesh and γ - Re ˜ θ t transition model, the aerodynamic characteristics of the NACA0012 airfoil at different turbulence intensities was calculated and compared with the experimental results, which verifies the reliability of the numerical method. Then, the effects of varied low Reynolds numbers and turbulence intensities on the aerodynamic performance of NACA0012 and SD7037 were investigated. The results show that higher turbulence intensity or Reynolds number leads to more stable airfoil aerodynamic performance, larger stalling angle, and earlier transition with a different mechanism. The generation and evolution of the laminar separation bubble (LSB) are closely related to Reynolds number, and it would change the effective shape of the airfoil, having a big influence on the airfoil’s aerodynamic characteristics. Compared with the symmetrical airfoil, the low-Reynolds-number airfoil can delay the occurrence of flow separation and produce more lift in the same conditions, which provides guidance for further airfoil design under TeDP jet flow.

A Computational Study on Airfoils at a Low Reynolds Number

2000 ◽  
Author(s):  
Ajit Pal Singh ◽  
S. H. Winoto ◽  
D. A. Shah ◽  
K. G. Lim ◽  
Robert E. K. Goh
Keyword(s):  
Reynolds Number ◽  
Computational Analysis ◽  
Computational Study ◽  
Low Reynolds Number ◽  
Micro Air Vehicles ◽  
Reynolds Numbers ◽  
Aerodynamic Performance ◽  
Low Reynolds Numbers ◽  
Study Results ◽  
Low Reynolds

Abstract Performance characteristics of some low Reynolds number airfoils for the use in micro air vehicles (MAVs) are computationally studied using XFOIL at a Reynolds number of 80,000. XFOIL, which is based on linear-vorticity stream function panel method coupled with a viscous integral formulation, is used for the analysis. In the first part of the study, results obtained from the XFOIL have been compared with available experimental data at low Reynolds numbers. XFOIL is then used to study relative aerodynamic performance of nine different airfoils. The computational analysis has shown that the S1223 airfoil has a relatively better performance than other airfoils considered for the analysis.

Using Turbulence Intensity and Reynolds Number to Predict Flow Separation on a Highly Loaded, Low-Pressure Gas Turbine Blade at Low Reynolds Numbers

2018 ◽  
Author(s):  
Kenneth Van Treuren ◽  
Tyler Pharris ◽  
Olivia Hirst
Keyword(s):  
Reynolds Number ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Turbulence Intensity ◽  
Flow Separation ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
High Altitudes ◽  
Low Reynolds Numbers ◽  
Low Pressure Turbine

The low-pressure turbine has become more important in the last few decades because of the increased emphasis on higher overall pressure and bypass ratios. The desire is to increase blade loading to reduce blade counts and stages in the low-pressure turbine of a gas turbine engine. Increased turbine inlet temperatures for newer cycles results in higher temperatures in the low-pressure turbine, especially the latter stages, where cooling technologies are not used. These higher temperatures lead to higher work from the turbine and this, combined with the high loadings, can lead to flow separation. Separation is more likely in engines operating at high altitudes and reduced throttle setting. At the high Reynolds numbers found at takeoff, the flow over a low-pressure turbine blade tends to stay attached. At lower blade Reynolds numbers (25,000 to 200,000), found during cruise at high altitudes, the flow on the suction surface of the low-pressure turbine blades is inclined to separate. This paper is a study on the flow characteristics of the L1A turbine blade at three low Reynolds numbers (60,000, 108,000, and 165,000) and 15 turbulence intensities (1.89% to 19.87%) in a steady flow cascade wind tunnel. With this data, it is possible to examine the impact of Reynolds number and turbulence intensity on the location of the initiation of flow separation, the flow separation zone, and the reattachment location. Quantifying the change in separated flow as a result of varying Reynolds numbers and turbulence intensities will help to characterize the low momentum flow environments in which the low-pressure turbine must operate and how this might impact the operation of the engine. Based on the data presented, it is possible to predict the location and size of the separation as a function of both the Reynolds number and upstream freestream turbulence intensity (FSTI). Being able to predict this flow behavior can lead to more effective blade designs using either passive or active flow control to reduce or eliminate flow separation.

On High-Performance Airfoil at Very Low Reynolds Number

2016 ◽  
Vol 28 (3) ◽  
pp. 273-285
Author(s):  
Katsuya Hirata ◽  
◽  
Ryo Nozawa ◽  
Shogo Kondo ◽  
Kazuki Onishi ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Flat Plate ◽  
High Performance ◽  
Low Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Slow Flow ◽  
Low Reynolds Numbers ◽  
Low Reynolds

[abstFig src='/00280003/02.jpg' width=""300"" text='Iso-Q surfaces of very-slow flow past an iNACA0015' ] The airfoil is often used as the elemental device for flying/swimming robots, determining its basic performances. However, most of the aerodynamic characteristics of the airfoil have been investigated at Reynolds numbers Re’s more than 106. On the other hand, our knowledge is not enough in low Reynolds-number ranges, in spite of the recent miniaturisation of robots. In the present study, referring to our previous findings (Hirata et al., 2011), we numerically examine three kinds of high-performance airfoils proposed for very-low Reynolds numbers; namely, an iNACA0015 (the NACA0015 placed back to front), an FPBi (a flat plate blended with iNACA0015 as its upper half) and an FPBN (a flat plate blended with the NACA0015 as its upper half), in comparison with such basic airfoils as a NACA0015 and an FP (a flat plate), at a Reynolds number Re = 1.0 × 102 using two- and three-dimensional computations. As a result, the FPBi shows the best performance among the five kinds of airfoils.

Influence of Turbulence Intensity on Annular Turbine Stator Aerodynamics at Low Reynolds Numbers

1999 ◽  
Author(s):  
Takayuki Matsunuma ◽  
Hiroyuki Abe ◽  
Yasukata Tsutsui
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Gas Turbines ◽  
Separation Zone ◽  
Reynolds Numbers ◽  
Pressure Probe ◽  
Single Element ◽  
Low Reynolds Numbers ◽  
Turbine Stator ◽  
Low Reynolds

The aerodynamic characteristics of turbine cascades are thought to be relatively satisfactory due to the favorable pressure of the accelerating flow. But within the low Reynolds number region of 6×104 where the 300kW ceramic gas turbines which are being developed under the New Sunshine project of Japan operate, the characteristics such as boundary layer separation, reattachment and secondary flow which lead to prominent power losses can not be easily predicted. In this research, experiments have been conducted to evaluate the performance of an annular turbine stator cascade, especially focused on the influence of inlet turbulence intensity at low Reynolds numbers. The Reynolds number, based on inlet condition, was varied from 2×104 to 12×104. The turbulence intensity was changed between 0.5% and 8.9% by setting turbulence generation sheets. The wake of the cascade was measured using a 5-hole pressure probe and a single element hot-wire anemometry. The Reynolds number was a determinative important parameter, while the turbulence intensity was found to have an insignificant effect on the overall total pressure loss of annular turbine stator at low Reynolds numbers. However, the increase in separation zone on suction surface and the decrease of passage vortices near the endwalls were observed locally with the increase in the inlet turbulence intensity. Instantaneous velocity signals proved the transformation of the flow structure in separation zone. The increase in profile loss (separation) and the decrease in net secondary loss (passage vonices) offset each other. Therefore, the net overall loss remains almost constant.

Measurements in a Turbine Cascade Flow Under Ultra Low Reynolds Number Conditions

2001 ◽  
Vol 124 (1) ◽  
pp. 100-106 ◽  
Author(s):  
Kenneth W. Van Treuren ◽  
Terrence Simon ◽  
Marc von Koller ◽  
Aaron R. Byerley ◽  
James W. Baughn ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Reynolds Numbers ◽  
Vortex Generators ◽  
Separation Region ◽  
Suction Surface ◽  
Low Reynolds Numbers ◽  
Free Stream Turbulence ◽  
Low Reynolds

With the new generation of gas turbine engines, low Reynolds number flows have become increasingly important. Designers must properly account for transition from laminar to turbulent flow and separation of the flow from the suction surface, which is strongly dependent upon transition. Of interest to industry are Reynolds numbers based upon suction surface length and flow exit velocity below 150,000 and as low as 25,000. In this paper, the extreme low end of this Reynolds number range is documented by way of pressure distributions, loss coefficients, and identification of separation zones. Reynolds numbers of 25,000 and 50,000 and with 1 percent and 8-9 percent turbulence intensity of the approach flow (free-stream turbulence intensity, FSTI) were investigated. At 25,000 Reynolds number and low FSTI, the suction surface displayed a strong and steady separation region. Raising the turbulence intensity resulted in a very unsteady separation region of nearly the same size on the suction surface. Vortex generators were added to the suction surface, but they appeared to do very little at this Reynolds number. At the higher Reynolds number of 50,000, the low-FSTI case was strongly separated on the downstream portion of the suction surface. The separation zone was eliminated when the turbulence level was increased to 8-9 percent. Vortex generators were added to the suction surface of the low-FSTI case. In this instance, the vortices were able to provide the mixing needed to re-establish flow attachment. This paper shows that massive separation at very low Reynolds numbers (25,000) is persistent, in spite of elevated FSTI and added vortices. However, at a higher Reynolds number, there is opportunity for flow reattachment either with elevated free-stream turbulence or with added vortices. This may be the first documentation of flow behavior at such low Reynolds numbers. Although it is undesirable to operate under these conditions, it is important to know what to expect and how performance may be improved if such conditions are unavoidable.

Numerical investigation of the effect of triangular cavity on the unsteady aerodynamics of NACA 0012 at a low Reynolds number

2021 ◽  
pp. 095441002110270
Author(s):  
Rajesh Yadav ◽  
Aslesha Bodavula
Keyword(s):  
Reynolds Number ◽  
Steady State ◽  
Unsteady Aerodynamics ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Accurate Solution ◽  
Low Reynolds Numbers ◽  
State Regime ◽  
Low Reynolds ◽  
Naca 0012

Time accurate numerical simulations were conducted to investigate the effect of triangular cavities on the unsteady aerodynamic characteristics of NACA 0012 airfoil at a Reynolds number of 50,000. Right-angled triangular cavities are placed at 10%, 25% and 50% chord location on the suction and have depths of 0.025c and 0.05c, measured normal to the surface of the airfoil. The second-order accurate solution to the RANS equations is obtained using a pressure-based finite volume solver with a four-equation transition turbulence model, γ–Re θt, to model the effect of turbulence. The two-dimensional results suggest that the cavity of depth 0.025c at 10% chord improves the aerodynamic efficiency ( l/d ratio) by 52%, at an angle of attack of α = 8°, wherein the flow is steady. The shallower triangular cavity when placed at 25%c and 50%c enhances the l/d ratio by only 10% and 17%, respectively, in the steady-state regime of angles of attack between α = 6° and 10°. The deeper cavity also enhances the l/d ratio by up to 13%, 22% and 14% at angles of attack between α = 6° and 10°. Even in the unsteady vortex shedding regime, at α =12° and higher, significant improvements in the time-averaged l/d ratios are observed for both cavity depths. The improvements in l/d ratio in the steady-state, pre-stall regime are primarily because of drag reduction while in the post-stall, unsteady regime, the improvements are because of enhancements in time-averaged C l values. The current finding can thus be used to enhance the aerodynamic performance of MAVs and UAVs that fly at low Reynolds numbers.

scholarly journals Aerodynamic characteristics of owl like airfoil at low reynolds number.

2022 ◽  
pp. 26-34
Author(s):  
Ishfaq Fayaz ◽  
Syeeda Needa Fathima ◽  
Y.D. Dwivedi
Keyword(s):  
Reynolds Number ◽  
Separation Bubble ◽  
Low Reynolds Number ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Pressure Side ◽  
Low Reynolds Numbers ◽  
Lift Curve ◽  
Low Reynolds

The computational investigation of aerodynamic characteristics and flow fields of a smooth owl-like airfoil without serrations and velvet structures.The bioinspired airfoil design is planned to serve as the main-wing for low-reynolds number aircrafts such as (MAV)micro air vechiles.The dependency of reynolds number on aerodynamics could be obtained at low reynolds numbers.The result of this experiment shows the owl-like airfoil is having high lift performance at very low speeds and in various wind conditions.One of the unique feature of owl airfoil is a separation bubble on the pressure side at low angle of attack.The separation bubble changes location from the pressure side to suction side as the AOA (angle of attack) increases. The reynolds number dependancy on the lift curve is insignificant,although there’s difference in drag curve at high angle of attacks.Eventually, we get the geometric features of the owl like airfoil to increase aerodynamic performance at low reynolds numbers.

scholarly journals Characteristics of an Annular Turbine Cascade at Low Reynolds Numbers

1998 ◽  
Author(s):  
Takayuki Matsunuma ◽  
Hiroyuki Abe ◽  
Yasukata Tsutsui ◽  
Koji Murata
Keyword(s):  
Reynolds Number ◽  
Gas Turbines ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Boundary Layer Separation ◽  
Aerodynamic Characteristics ◽  
Secondary Flows ◽  
Suction Surface ◽  
Low Reynolds Numbers ◽  
Low Reynolds

The aerodynamic characteristics of turbine cascades are thought to be relatively satisfactory due to the favorable pressure gradient of the accelerating flow. But within the low Reynolds number region of approximately 6×104 where the 300kW ceramic gas turbines which are being developed under the New Sunshine Project of Japan operate, the characteristics such as boundary layer separation, reattachment and secondary flow which lead to prominent power losses can not be easily predicted. In this research, experiments have been conducted to evaluate the performance of an annular turbine stator cascade. Wakes of the cascade were measured using a single hot wire and five hole pressure tube, for a range of blade chord Reynolds numbers based on the inlet condition from 2×104 to 12×104. Flow visualizations on the suction surface of the blade were carried out using oil film method. At low Reynolds numbers, the flow structure in the annular cascade was quite complex and three-dimensional. The separation line on the suction surface moved upstream due to the decrease of Reynolds number. In addition, the growth of secondary flows, i.e., passage vortices and leakage vortex, was extremely under the influence of Reynolds number.

Measurements in a Turbine Cascade Flow Under Ultra Low Reynolds Number Conditions

2001 ◽  
Author(s):  
Kenneth W. Van Treuren ◽  
Terrence Simon ◽  
Marc von Koller ◽  
Aaron R. Byerley ◽  
James W. Baughn ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Low Reynolds Number ◽  
Reynolds Numbers ◽  
Vortex Generators ◽  
Separation Region ◽  
Suction Surface ◽  
Number Range ◽  
Low Reynolds Numbers ◽  
Low Reynolds

With the new generation of gas turbine engines, low Reynolds number flows have become increasingly important. Designers must properly account for transition from laminar to turbulent flow and separation of the flow from the suction surface, which is strongly dependent upon transition. Of interest to industry are Reynolds numbers based upon suction surface length and flow exit velocity below 150,000 and as low as 25,000. In this paper, the extreme low end of this Reynolds number range is documented by way of pressure distributions, loss coefficients and identification of separation zones. Reynolds numbers of 25,000 and 50,000 and with 1% and 8–9% turbulence intensity of the approach flow (Free Stream Turbulence Intensity, FSTI) were investigated. At 25,000 Reynolds number and low FSTI, the suction surface displayed a strong and steady separation region. Raising the turbulence intensity resulted in a very unsteady separation region of nearly the same size on the suction surface. Vortex generators were added to the suction surface, but they appeared to do very little at this Reynolds number. At the higher Reynolds number of 50,000, the low-FSTI case was strongly separated on the downstream portion of the suction surface. The separation zone was eliminated when the turbulence level was increased to 8–9%. Vortex generators were added to the suction surface of the low-FSTI case. In this instance, the vortices were able to provide the mixing needed to reestablish flow attachment. This paper shows that massive separation at very low Reynolds numbers (25,000) is persistent, in spite of elevated FSTI and added vortices. However, at a higher Reynolds number, there is opportunity for flow reattachment either with elevated freestream turbulence or with added vortices. This may be the first documentation of flow behavior at such low Reynolds numbers. Though undesirable to operate under these conditions, it is important to know what to expect and how performance may be improved if such conditions are unavoidable.

Sign in / Sign up

Export Citation Format

Share Document