scholarly journals Numerical Simulation of Breaking Wave Loading on Standing Circular Cylinders with Different Transverse Inclined Angles

2020 ◽  
Vol 10 (4) ◽  
pp. 1347
Author(s):  
Sen Qu ◽  
Shengnan Liu ◽  
Muk Chen Ong ◽  
Shuzheng Sun ◽  
Huilong Ren
Keyword(s):  
Experimental Data ◽  
Vertical Cylinder ◽  
Wave Force ◽  
High Order ◽  
Numerical Results ◽  
Circular Cylinders ◽  
Wave Forces ◽  
Breaking Wave ◽  
Time Step ◽  
Inclined Angle

The purpose of this paper is to numerically simulate the breaking wave past a standing cylinder with different transverse inclined angles. The numerical simulations are carried out by solving the Unsteady Reynolds-Averaged Navier–Stokes (URANS) equations with the k − ω S S T turbulence model. The air–water interface is captured using the Volume of Fluid (VOF) method. The convergence studies on the grid and time-step are performed by examining the total horizontal breaking wave forces on the vertical cylinder. The present numerical results have been validated with the published experimental data. A good agreement is obtained between the present numerical results and the experimental data in terms of the surface elevation and the horizontal breaking wave force. Moreover, the total horizontal breaking wave force is decomposed into low-order and high-order wave forces through Fast Fourier Transform (FFT). It is observed that the free surface elevations in front of the cylinder and the normalized high-order wave force have a minimum value when the transverse inclined angle of the cylinder is 45°. The secondary load causing the higher-harmonic ringing motion of structures is not observed when the cylinder is placed with the transverse inclined angles of 30° and 45°.

Numerical Simulations of Breaking Waves and Steep Waves Past a Vertical Cylinder at Different Keulegan–Carpenter Numbers

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Shengnan Liu ◽  
Muk Chen Ong ◽  
Charlotte Obhrai
Keyword(s):  
Dynamic Pressure ◽  
Vertical Cylinder ◽  
Breaking Waves ◽  
Numerical Results ◽  
Wave Forces ◽  
Breaking Wave ◽  
Wave Loads ◽  
Time Step ◽  
Two Phase ◽  
Steep Waves

A three-dimensional (3D) numerical two-phase flow model based on solving unsteady Reynolds-averaged Navier–Stokes (URANS) equations has been used to simulate breaking waves and steep waves past a vertical cylinder on a 1:10 slope. The volume of fluid (VOF) method is employed to capture the free surface and the k–ω shear–stress transport (k–ω SST) turbulence model is used to simulate the turbulence effects. Mesh and time-step refinement studies have been conducted. The numerical results of wave forces on the structure are compared with the experimental data (Irschik et al., 2004, “Breaking Wave Loads on a Slender Pile in Shallow Water,” Coastal Engineering, Vol. 4, World Scientific, Singapore, pp. 568–581) to validate the numerical model, and the numerical results are in good agreement with the measured data. The wave forces on the structure at different Keulegan–Carpenter (KC) numbers are discussed in terms of the slamming force. The secondary load cycles are observed after the wave front past the structure. The dynamic pressure and velocity distribution, as well as the characteristics of the vortices around the structure at four important time instants, are studied.

Numerical Modelling of Breaking Wave Interaction With a Group of Four Vertical Slender Cylinders in Square Arrangements

2016 ◽  
Author(s):  
Mayilvahanan Alagan Chella ◽  
Hans Bihs ◽  
Arun Kamath ◽  
Dag Myrhaug ◽  
Øivind Asgeir Arnsten
Keyword(s):  
Experimental Data ◽  
Free Surface ◽  
Numerical Model ◽  
Numerical Modelling ◽  
Wave Interaction ◽  
Wave Force ◽  
Wave Forces ◽  
Breaking Wave ◽  
Square Configuration ◽  
Breaking Wave Forces

The main purpose of the study is to investigate the breaking wave interaction with a group of four circular cylinders. The physical process of wave breaking involves many parameters and an accurate numerical modelling of breaking waves and the interaction with a structure remain a challenge. In the present study, the open-source (Computational Fluid Dynamics) CFD model REEF3D is used to simulate the breaking wave interaction with the multiple cylinders. The numerical model is based on the incompressible Reynolds Averaged Navier-Stokes (RANS) equations, the level set method for the free surface and the k–ω model for turbulence. The model uses a 5th-order conservative finite difference WENO scheme for the convective discretization and a 3rd-order Runge-Kutta scheme for time discretization. The numerical model is validated with experimental data of large-scale experiments for the free surface elevation and the breaking wave force on a single cylinder. A good agreement is seen between the numerical results and experimental data. Two different configurations with four cylinders are examined: in-line square configuration and diamond square configuration. The breaking wave forces on each cylinder in the group are computed for the two cases and the results are compared with the breaking wave force on a single isolated cylinder. Further, the study investigates the water surface elevations and the free surface flow features around the cylinders. In general, the cylinders in both configurations experience the maximum forces lower than the maximum force on a single cylinder. The results of the present study show that the interference effects from the neighbouring cylinders in a group strongly influence the kinematics around and the breaking wave forces on them.

Breaking Wave Interaction With a Group of Four Vertical Slender Cylinders in Two Square Arrangements

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Mayilvahanan Alagan Chella ◽  
Hans Bihs ◽  
Arun Kamath ◽  
Dag Myrhaug ◽  
Øivind Asgeir Arntsen
Keyword(s):  
Experimental Data ◽  
Free Surface ◽  
Numerical Model ◽  
Wave Interaction ◽  
Wave Force ◽  
Maximum Force ◽  
Wave Forces ◽  
Breaking Wave ◽  
Square Configuration ◽  
Breaking Wave Forces

The main purpose of the study is to investigate the breaking wave interaction with a group of four circular cylinders. The physical process of wave breaking involves many parameters, and an accurate numerical modeling of breaking waves and the interaction with a structure remain a challenge. In the present study, the open-source computational fluid dynamics (CFD) model REEF3D is used to simulate the breaking wave interaction with multiple cylinders. The numerical model is based on the incompressible Reynolds-averaged Navier–Stokes (RANS) equations, the level set method for the free surface, and the k–ω model for turbulence. The numerical model is validated with experimental data of large-scale experiments for the free surface elevation and the breaking wave force on a single cylinder. A good agreement is obtained between the numerical results and experimental data. Two different configurations with four cylinders are examined: in-line square configuration and diamond square configuration. For both configurations, three different tank widths and four different spacings between the cylinders are investigated. The breaking wave forces on each cylinder in the group are computed for each case for the two configurations, and the results are compared with the breaking wave force on a single isolated cylinder. Furthermore, the study investigates the water surface elevations and the free surface flow features around the cylinders. For the closely spaced cylinders in a relatively narrower tank, the cylinders in both configurations experience the maximum forces lower than the maximum force on a single cylinder. But for the widely spaced cylinder in a relatively wider tank, the forces are higher and lower for the upstream cylinders and downstream cylinders, respectively, than the maximum force on a single isolated cylinder. The results of the present study show that the interference effects from the neighboring cylinders in a group strongly influence the kinematics around and the breaking wave forces on them.

scholarly journals Characteristics of Breaking Wave Forces on Piles over a Permeable Seabed

2021 ◽  
Vol 9 (5) ◽  
pp. 520
Author(s):  
Zhenyu Liu ◽  
Zhen Guo ◽  
Yuzhe Dou ◽  
Fanyu Zeng
Keyword(s):  
Wave Breaking ◽  
Stokes Equations ◽  
Slope Angle ◽  
Wave Force ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Secondary Wave ◽  
Wave Forces ◽  
Breaking Wave ◽  
Breaking Wave Forces

Most offshore wind turbines are installed in shallow water and exposed to breaking waves. Previous numerical studies focusing on breaking wave forces generally ignored the seabed permeability. In this paper, a numerical model based on Volume-Averaged Reynolds Averaged Navier–Stokes equations (VARANS) is employed to reveal the process of a solitary wave interacting with a rigid pile over a permeable slope. Through applying the Forchheimer saturated drag equation, effects of seabed permeability on fluid motions are simulated. The reliability of the present model is verified by comparisons between experimentally obtained data and the numerical results. Further, 190 cases are simulated and the effects of different parameters on breaking wave forces on the pile are studied systematically. Results indicate that over a permeable seabed, the maximum breaking wave forces can occur not only when waves break just before the pile, but also when a “secondary wave wall” slams against the pile, after wave breaking. With the initial wave height increasing, breaking wave forces will increase, but the growth can decrease as the slope angle and permeability increase. For inclined piles around the wave breaking point, the maximum breaking wave force usually occurs with an inclination angle of α = −22.5° or 0°.

Second-Order Diffraction Loads on Plural Vertical Cylinder With Arbitrary Cross Sections

1987 ◽  
Vol 109 (4) ◽  
pp. 314-319
Author(s):  
K. Masuda ◽  
W. Kato ◽  
H. Ishizuka
Keyword(s):  
Boundary Value Problem ◽  
Cross Sections ◽  
Present Method ◽  
Boundary Value ◽  
Vertical Cylinder ◽  
Wave Force ◽  
Second Order ◽  
Wave Forces ◽  
Order Diffraction ◽  
Rectangular Cylinders

The purpose of the present study is development of a powerful numerical method for calculating second-order diffraction loads on plural vertical cylinder with arbitrary cross sections. According to the present method, second-order wave force can be obtained from a linear radiation potential without solving second-order boundary value problem. The boundary value problem for the radiation potential is solved with the hybrid boundary element method. The computations for circular and rectangular cylinders were carried out and compared with the experiments. In addition, second-order wave forces on twin circular cylinder are calculated with the present method.

Numerical Simulations of Regular and Irregular Wave Forces on a Horizontal Semi-Submerged Cylinder

2017 ◽  
Author(s):  
Shengnan Liu ◽  
Muk Chen Ong ◽  
Charlotte Obhrai ◽  
Sopheak Seng
Keyword(s):  
Experimental Data ◽  
Free Surface ◽  
Numerical Simulations ◽  
Stokes Equations ◽  
Wave Length ◽  
Wave Structure ◽  
Numerical Results ◽  
Irregular Waves ◽  
Wave Forces ◽  
Submerged Cylinder

Two-dimensional (2D) numerical simulations have been performed using OpenFOAM (an open source CFD software package [1]) and waves2Foam (an OpenFOAM based add-on library for wave generations and absorption [2]) to investigate free surface waves past one fixed horizontally semi-submerged cylinder. The 2-D simulations are carried out by solving Navier-Stokes equations which are discretized based on finite volume method (FVM). Volume of Fluid (VOF) method is employed to capture the free surface in the numerical wave tank. Validation studies have been performed by comparing the numerical results of Stokes first-order wave past a semi-submerged circular cylinder with the published experimental data at different incident wave properties. The numerical results are in good agreement with the experimental data. Subsequently, regular and irregular waves past semi-submerged cylinder at different wave heights and the wave lengths are computed numerically to investigate the effect of the wave height and wave length on wave-structure interaction. The numerical results for irregular waves are compared with those induced by regular waves.

scholarly journals Horizontal Forces Due to Waves Acting on Large Vertical Cylinders in Deep Water

1972 ◽  
Vol 94 (4) ◽  
pp. 862-866
Author(s):  
E. R. Johnson
Keyword(s):  
Deep Water ◽  
Large Diameter ◽  
Wave Force ◽  
Circular Cylinders ◽  
Wave Forces ◽  
Typical Application ◽  
Model Studies ◽  
Horizontal Wave ◽  
Horizontal Wave Force ◽  
Vertical Cylinders

The special case of horizontal wave forces on large vertical cylinders in deep water is considered. The typical application for such a case is the calculation of horizontal forces on column stabilized floating ocean platforms. Existing literature discussing horizontal wave forces on cylinders does not generally agree on how to predict these forces. Since for large diameter cylinders in deep water the maximum force is completely inertial, the problem of deriving a solution is considerably simplified. In this study, an expression for the maximum horizontal wave force on large diameter circular cylinders mounted vertically in deep water has been analytically derived. Experimental model studies were also conducted and the resulting measured forces were within 20 percent of predicted forces. An example of how to predict horizontal wave forces using the methods of this report is given.

Calculation of Wave Forces on Cylindrical Piles Using a 3D Numerical Wave Tank

2013 ◽  
Author(s):  
Arun Kamath ◽  
Hans Bihs ◽  
Øivind A. Arntsen
Keyword(s):  
Numerical Model ◽  
Stokes Equations ◽  
Practical Interest ◽  
Vertical Cylinder ◽  
Free Water ◽  
Wave Force ◽  
Weno Scheme ◽  
Wave Forces ◽  
Single Cylinder ◽  
Cylindrical Piles

Offshore constructions generally include a large number of vertical cylinders in the support structure. The calculation of wave forces on a vertical cylinder and hydrodynamic effects on it in the presence of neighbouring cylinders is of practical interest. In this paper, a 3D numerical model is used to calculate wave forces on bottom fixed cylindrical piles. Two cases are considered in this study: a single cylinder and a pair of tandem cylinders. A scenario with multiple cylindrical structures in close proximity introduces complex wave-structure interactions and would be of great interest to observe this in detail in a three-dimensional simulation. The wave force exerted on a cylindrical pile is numerically calculated by integrating the pressure and the wall shear stress around the surface of the cylinder. In the case of the single cylinder, the force calculated by the model is compared to the force predicted by the Morison formula and MacCamy-Fuchs theory. In the second case, the pair of cylinders is aligned in the direction of the incoming waves. The numerically calculated inline wave force on each cylinder is compared to the analytical solution for this setup and a good agreement is seen. The Reynolds-Averaged Navier-Stokes equations are used as the governing equations for the fluid flow in the numerical model. The convective terms are discretized using a 5th-order conservative finite difference WENO scheme. A 3rd-order accurate TVD Range-Kutta scheme is used for time discretization. Chorin’s projection method is used to discretize the pressure. The Poisson equation for pressure is solved using a preconditioned BiCGStab algorithm. The level set method is used to obtain a sharp representation of the free water surface. Turbulence in the flow is simulated using the k-ω model. The numerical model is adapted to parallel processing using the MPI library to improve the computing performance of the code.

Computational Fluid Dynamics Simulations of Regular and Irregular Waves Past a Horizontal Semi-Submerged Cylinder

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Shengnan Liu ◽  
Muk Chen Ong ◽  
Charlotte Obhrai ◽  
Sopheak Seng
Keyword(s):  
Free Surface ◽  
Numerical Simulations ◽  
Wave Height ◽  
Stokes Equations ◽  
Wave Force ◽  
Numerical Results ◽  
Irregular Waves ◽  
Wave Forces ◽  
Regular Waves ◽  
Peak Period

Two-dimensional (2D) numerical simulations have been performed to investigate both regular and irregular waves past a fixed horizontally semisubmerged circular cylinder. The 2D simulations are carried out by solving Navier–Stokes equations discretized by finite volume method. Volume of fluid (VOF) method is employed to capture the free surface in the numerical wave tank (NWT). Validation studies have been performed by comparing the numerical results of free surface waves past the cylinder with the published experimental and numerical data. The present numerical results are in good agreement with both the experimental and the other numerical results in terms of hydrodynamic forces and free surface elevation. Subsequently, the effects of the wave height and the wavelength on wave–structure interaction are investigated by conducting numerical simulations on the regular and the irregular waves past a semisubmerged cylinder at different wave heights and the wavelengths. The averaged and maximum vertical wave forces on the cylinder increase with the increasing wave height. The numerical results for the irregular waves are compared with those induced by the regular waves in terms of the maximum and averaged vertical wave forces. When the significant wave height and the spectral peak period of the irregular waves are equal to the wave height and the wave period of the regular waves, the maximum vertical wave force induced by the irregular waves is larger than that induced by the regular waves, meanwhile, the average vertical wave forces have the contrary relationship.

Numerical Simulation of Nonlinear Wave Diffraction by a Vertical Cylinder

1992 ◽  
Vol 114 (1) ◽  
pp. 36-44 ◽  
Author(s):  
C. Yang ◽  
R. C. Ertekin
Keyword(s):  
Experimental Data ◽  
Circular Cylinder ◽  
Nonlinear Wave ◽  
Wave Diffraction ◽  
Three Dimensional ◽  
Vertical Cylinder ◽  
Radiation Condition ◽  
Wave Force ◽  
Second Order ◽  
Time Stepping

A three-dimensional time domain approach is used to study nonlinear wave diffraction by a fixed, vertical circular-cylinder that extends to the sea floor. In this approach, the development of the flow can be obtained by a time-stepping procedure, in which the velocity potential of the flow at any instant of time is obtained by the boundary-element method. In the numerical calculations, the exact body-boundary condition is satisfied on the instantaneous wetted surface of the cylinder, and an extended Sommerfeld condition is developed and used as the numerical radiation condition. The fourth-order Adams-Bashford method is employed in the time stepping scheme. Calculations are done to obtain the nonlinear diffraction of solitary waves and Stokes second-order waves by a vertical circular-cylinder. Numerical results are compared with the available linear and second-order wave-force predictions for some given wave height and wavelength conditions, and also with experimental data. Present horizontal force results agree better with the experimental data than the previous predictions.

Sign in / Sign up

Export Citation Format

Share Document