scholarly journals Blast-Resistant Performance of Hybrid Fiber-Reinforced Concrete (HFRC) Panels Subjected to Contact Detonation

2019 ◽  
Vol 10 (1) ◽  
pp. 241
Author(s):  
Wenjin Yao ◽  
Weiwei Sun ◽  
Ze Shi ◽  
Bingcheng Chen ◽  
Le Chen ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Blast Resistance ◽  
Plain Concrete ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Hybrid Fiber ◽  
Hybrid Effect ◽  
Pva Fiber ◽  
Resistance Performance

This paper experimentally investigates the blast-resistant characteristics of hybrid fiber-reinforced concrete (HFRC) panels by contact detonation tests. The control specimen of plain concrete, polypropylene (PP), polyvinyl alcohol (PVA) and steel fiber-reinforced concrete were prepared and tested for characterization in contrast with PP-Steel HFRC and PVA-Steel HFRC. The sequent contact detonation tests were conducted with panel damage recorded and measured. Damaged HFRC panels were further comparatively analyzed whereby the blast-resistance performance was quantitively assessed via damage coefficient and blast-resistant coefficient. For both PP-Steel and PVA-Steel HFRC, the best blast-resistant performance was achieved at around 1.5% steel + 0.5% PP-fiber hybrid. Finally, the fiber-hybrid effect index was introduced to evaluate the hybrid effect on the explosion-resistance performance of HFRC panels. It revealed that neither PP-fiber or PVA-fiber provide positive hybrid effect on blast-resistant improvement of HFRC panels.

scholarly journals A Comparative Study on Blast-Resistant Performance of Steel and PVA Fiber-Reinforced Concrete: Experimental and Numerical Analyses

Crystals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 707
Author(s):  
Le Chen ◽  
Weiwei Sun ◽  
Bingcheng Chen ◽  
Sen Xu ◽  
Jianguo Liang ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Blast Resistance ◽  
Natural Extension ◽  
Fiber Reinforced Concrete ◽  
Particle Model ◽  
Model Parameters ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Numerical Predictions ◽  
Pva Fiber

This paper deals with the blast-resistant performance of steel fiber-reinforced concrete (SFRC) and polyvinyl alcohol (PVA) fiber-reinforced concrete (PVA-FRC) panels with a contact detonation test both experimentally and numerically. With 2% fiber volumetric content, SFRC and PVA-FRC specimens were prepared and comparatively tested in comparison with plain concrete (PC). SFRC was found to exhibit better blast-resistant performance than PVA-FRC. The dynamic mechanical responses of FRC panels were numerically studied with Lattice Discrete Particle Model-Fiber (LDPM-F) which was recently developed to simulate the meso-structure of quasi-brittle materials. The effect of dispersed fibers was also introduced in this discrete model as a natural extension. Calibration of LDPM-F model parameters was achieved by fitting the compression and bending responses. A numerical model of FRC contact detonation was then validated against the blast test results in terms of damage modes and crater dimensions. Finally, FRC panels with different fiber volumetric fractions (e.g., 0.5%, 1.0% and 1.5%) under blast loadings were further investigated with the validated LDPM-F blast model. The numerical predictions shed some light on the fiber content effect on the FRC blast resistance performance.

Experimental Study on Fiber Reinforced Concrete

2008 ◽  
Vol 400-402 ◽  
pp. 391-394
Author(s):  
Ming Hui Wei ◽  
Yi Ping Liu ◽  
Li Qun Tang ◽  
Xiao Qing Huang
Keyword(s):  
Reinforced Concrete ◽  
Cost Estimation ◽  
Steel Fiber ◽  
Plain Concrete ◽  
Fiber Reinforced Concrete ◽  
Polymer Fiber ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Hybrid Fiber ◽  
Polymer Modified Concrete

Flexure behaviors of plain concrete (PC), steel fiber reinforced concrete (SFRC), polymer modified concrete (PMC), steel fiber reinforced and polymer modified concrete (SFRPMC) and hybrid fiber reinforced concrete (HFRC) with steel fiber and polymer fiber are studied in this paper, flexure tests were carried out and flexure strengths of the five different materials with different mixture ratios were measured and compared. Flexure ductility of PC, PMC, SFRC, and SFRPMC were calculated and compared. In addition, considering performance and cost estimation comprehensively, HFRC is recommended, preliminary tests show that HFRC may be one of the potential materials for bridge pavement.

Experimental Study on Impact Resistance of PVA Fiber Reinforced Cement-Based Composite

2014 ◽  
Vol 584-586 ◽  
pp. 1630-1634
Author(s):  
Xin Hua Cai ◽  
Zhen He ◽  
Wen Liu
Keyword(s):  
Reinforced Concrete ◽  
Steel Fiber ◽  
Impact Resistance ◽  
Plain Concrete ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Reinforced Cement ◽  
Pva Fiber ◽  
The Impact

PVA fiber reinforced cement-based composite is a new high-performance cement-based composite material, which usually manufactured with PVA short fibers (does not exceed 2.5% vol.) and cement-based matrix. It has a significant strain-hardening characteristic and excellent crack controlling ability. Its ultimate tensile strain is up to 3% and crack width is not exceed 100μm. PVA fiber reinforced cement-based composite can be utilized to fabricated high energy absorption opponents, such as protective shield, seismic joint, impact-resistant site, etc. In this paper, the basic mechanical properties of PVA fiber reinforced cement-based composite has been tested and verified first. Then the impact resistance of PVA reinforced cement-based composite has been investigated via drop weight impact test, and compared with ones of plain concrete and steel fiber reinforced concrete with the same strength grade. Through analyzing the test results, it is concluded that PVA reinforced cement-based composite’s impact energy absorption is 48 times than plain concrete, and 9 times than steel fiber reinforced concrete respectively. The impact numbers of PVA reinforced cement-based composite is slightly lower than steel fiber reinforced concrete, but its impact absorption energy after initial cracking is 15 times than steel fiber reinforced concrete. In conclusion, PVA reinforced cement-based composite is an excellent impact material.

scholarly journals Effect of the Notch-to-Depth Ratio on the Post-Cracking Behavior of Steel-Fiber-Reinforced Concrete

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 445
Author(s):  
José Valdez Aguilar ◽  
César A. Juárez-Alvarado ◽  
José M. Mendoza-Rangel ◽  
Bernardo T. Terán-Torres
Keyword(s):  
Reinforced Concrete ◽  
Plain Concrete ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Cracking Behavior ◽  
Bending Tests ◽  
Depth Ratio ◽  
Residual Performance ◽  
Concrete Control

Concrete barely possesses tensile strength, and it is susceptible to cracking, which leads to a reduction of its service life. Consequently, it is significant to find a complementary material that helps alleviate these drawbacks. The aim of this research was to determine analytically and experimentally the effect of the addition of the steel fibers on the performance of the post-cracking stage on fiber-reinforced concrete, by studying four notch-to-depth ratios of 0, 0.08, 0.16, and 0.33. This was evaluated through 72 bending tests, using plain concrete (control) and fiber-reinforced concrete with volume fibers of 0.25% and 0.50%. Results showed that the specimens with a notch-to-depth ratio up to 0.33 are capable of attaining a hardening behavior. The study concludes that the increase in the dosage leads to an improvement in the residual performance, even though an increase in the notch-to-depth ratio has also occurred.

scholarly journals Application of fiber-reinforced concrete lining for fault-crossing tunnels in meizoseismal area to improving seismic performance

2020 ◽  
Vol 12 (7) ◽  
pp. 168781402094402
Author(s):  
Dong An ◽  
Zheng Chen ◽  
Linghan Meng ◽  
Guangyao Cui
Keyword(s):  
Reinforced Concrete ◽  
Seismic Performance ◽  
Steel Fiber ◽  
Tunnel Lining ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Hybrid Fiber ◽  
Meizoseismal Area ◽  
Secondary Lining

The fault-crossing tunnel in meizoseismal area is directly subjected to strong ground motion, which leads to the failure of the tunnel lining. In order to improve the seismic safety of tunnel, fiber-reinforced concrete is applied to tunnel lining in this article. Taking the section of Zhongyi tunnel crossing Wanlong fault as an example, seismic performance of fiber-reinforced concrete tunnel lining was studied by finite difference numerical calculation software FLAC3D. The seismic displacement, stress response, and side wall convergence of secondary lining structures which are plain concrete, steel fiber-reinforced concrete, and steel-basalt hybrid fiber-reinforced concrete were comparatively analyzed. Moreover, the safety factor of each lining structure was investigated with the present numerical model. With the obtained data, seismic performance of steel-basalt hybrid fiber-reinforced concrete secondary lining is better than that of steel fiber-reinforced concrete secondary lining. The results may provide references for seismic design of fault-crossing tunnels in meizoseismal area.

scholarly journals Fasteners in Steel Fiber Reinforced Concrete Subjected to Increased Loading Rates

Fibers ◽  
2018 ◽  
Vol 6 (4) ◽  
pp. 93 ◽  
Author(s):  
Boglárka Bokor ◽  
Máté Tóth ◽  
Akanshu Sharma
Keyword(s):  
Reinforced Concrete ◽  
Static Loading ◽  
Steel Fiber ◽  
Plain Concrete ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Loading Rates ◽  
Rate Dependent ◽  
Ultimate Resistance

Increased loading rates on fasteners may be caused by high ground accelerations as a consequence of e.g., nuclear explosions, earthquakes or car collisions. It was concluded by Hoehler et al. (2006) that fasteners under rapid loading rates show an increased ultimate resistance in the concrete dominant failure modes or the ultimate resistance is at least as large as under quasi-static loading. Due to the increased demand on using fasteners in steel fiber reinforced concrete (SFRC), it is intended to show how the ultimate concrete cone capacity of fasteners changes under higher than quasi-static loading rate in normal plain concrete (PC) and in SFRC. This paper presents the results of an extensive experimental program carried out on single fasteners loaded in tension in normal plain concrete and in SFRC. The test series were conducted using a servo-hydraulic loading cylinder. The tests were performed in displacement control with a programmed ramp speed of 1, 100, 1000, and 3500 mm/min. This corresponded to calculated initial loading rates ranging between 0.4 and 1600 kN/s. The results of the tension tests clearly show that the rate-dependent behavior of fasteners in SFRC with 30 and 50 kg/m3 hooked-end-type fibers fits well to the previously reported rate-dependent concrete cone behavior in normal plain concrete. Additionally, a positive influence of the fibers on the concrete cone capacity is clearly visible.

Mechanical Properties of Hybrid Basalt-Polyvinyl Alcohol (PVA) Fiber Reinforced Concrete

2017 ◽  
Vol 744 ◽  
pp. 3-7 ◽  
Author(s):  
Asif Jalal ◽  
Nasir Shafiq ◽  
Ehsan Nikbakht ◽  
Rabinder Kumar ◽  
Muhammad Zahid
Keyword(s):  
Reinforced Concrete ◽  
Volume Fraction ◽  
Peak Load ◽  
High Strength ◽  
Plain Concrete ◽  
Fiber Reinforced Concrete ◽  
Maximum Deflection ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Pva Fiber

This study focuses on the study of the mechanical behavior of non-metallic hybrid Basalt-PVA fiber reinforced concrete. Total five mixes were investigated with one control plain concrete and four with fiber volume fraction of 0.3%, 0.6%, 0.9% and 1.2%. Basalt and PVA were used in same quantity. Fiber decreased workability, therefore superplasticizer was used to maintain workability constant. The increase in superplasticizer and fiber content decreased compression, split tensile and flexure strengths because of formation of big size pores. Whereas fiber enhanced the post peak load zone in the load-deflection curve. Fiber improved the bridging action by increasing energy absorption. Fiber vanished the brittle behavior of high strength concrete and increased first crack toughness, flexure toughness and also maximum deflection. 0.3% volume fraction of fiber was found to be optimum with the negligible decrease in compression, split tensile and flexure strength while caused the considerable increase in first crack toughness, flexure toughness, and maximum deflection.

Synergistic Effects and Cracking Bending Strength for Steel-Polypropylene Hybrid Fiber Reinforced Concrete

2013 ◽  
Vol 652-654 ◽  
pp. 1237-1241
Author(s):  
Guo Dong Mei ◽  
Xiao Fan Liu ◽  
Ji Xiang Li ◽  
Wen Fu Duan
Keyword(s):  
Reinforced Concrete ◽  
Synergistic Effect ◽  
Bending Strength ◽  
Steel Fiber ◽  
Synergistic Effects ◽  
Polypropylene Fiber ◽  
Plain Concrete ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Hybrid Fiber

The cracking bending strength for steel-polypropylene hybrid fiber reinforced concrete (HFRC) had been studied based on experimental test. the inicial cracking strength achieve significant improvement compare to plain concrete, and the highest increase is 16.7%. There is a synergistic effect exist when steel fiber is 1.0% in volume or polypropylene fiber is 0.1% in volume, and the synergistic effect raise to vertex (1.043) when both of those two requirements are fulfilled.

Study on Dry-Shrinkage Properties of Layer Hybrid Fiber Reinforced Concrete

2012 ◽  
Vol 204-208 ◽  
pp. 4055-4058
Author(s):  
Dong Qing He ◽  
Yan Yan Zhao
Keyword(s):  
Reinforced Concrete ◽  
Mass Loss ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Hybrid Fiber ◽  
Shrinkage Ratio ◽  
Ordinary Concrete ◽  
Dry Shrinkage ◽  
Layer Steel

In order to study the effects of the application of layer steel fibers and polypropylene fibers on dry-shrinkage properties of concrete, the contrast experiments on the dry-shrinkage ratio and mass-loss ratio of ordinary concrete(OC), layer steel fiber reinforced concrete(LSFRC) and layer hybrid fiber reinforced concrete(LHFRC) under constant temperature (20±2°C) and constant humidity(relative humidity 60±5%) condition were carried out. The dry-shrinkage ratio of LHFRC is smaller obviously than OC’s and LSFRC’s, and achieve a reduction of 26.9%, the dry-shrinkage ratio of LHFRC after adding grinding slag and fly ash achieve a reduction of 40.2% at the age of 180 days. However, the mass-loss of LHFRC is larger than OC’s, and achieve an increment of 18.3% at the age of 180 days, LHFRC after adding grinding slag and fly ash’s is consistent with OC’s. The dry-shrinkage properties of concrete will be improved remarkably by adding layer hybrid fiber.

Evaluation on the Blast Resistance of Fiber Reinforced Concrete

2011 ◽  
Vol 311-313 ◽  
pp. 1588-1593 ◽  
Author(s):  
Jeong Soo Nam ◽  
Gyu Yong Kim ◽  
Hiroyuki Miyauchi ◽  
Young Seok Jeon ◽  
Heon Kyu Hwang
Keyword(s):  
Reinforced Concrete ◽  
Fracture Mode ◽  
Steel Fiber ◽  
Blast Resistance ◽  
Fiber Reinforced Concrete ◽  
Back Side ◽  
Fiber Reinforced ◽  
Emulsion Explosive ◽  
Loss Of Life ◽  
Resistance Performance

Recently, the damaged building and loss of life have been increasing by man-made disasters. In this study, the blast resistance performance of fiber reinforced concrete against explosion was evaluated by the emulsion explosive and AUTODYN. The concrete without fiber was penetrated by emulsion explosive of 4605 kJ/kg and its back side was fractured heavily. The concretes with PVA, PE and Steel fiber have a higher blast resistance than that of concrete without fiber. Consequentially, the blast resistance of concrete was analyzed from viewpoint of fracture mode by AUTODYN and it was concluded that the fiber content is a beneficial for the blast resistance performance of concrete.

Sign in / Sign up

Export Citation Format

Share Document