scholarly journals Clocking and Potential Effects in Combustor–Turbine Stator Interactions

Aerospace ◽  
2021 ◽  
Vol 8 (10) ◽  
pp. 285
Author(s):  
Pawel Flaszynski ◽  
Michal Piotrowicz ◽  
Tommaso Bacci
Keyword(s):  
Guide Vane ◽  
Turbulence Models ◽  
Flow Distribution ◽  
Aircraft Engine ◽  
Potential Effect ◽  
Flow Conditions ◽  
Azimuthal Position ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Stress Models

Investigations of combustors and turbines separately have been carried out for years by research institutes and aircraft engine companies, but there are still many questions about the interaction effect. In this paper, a prediction of a turbine stator’s potential effect on flow in a combustor and the clocking effect on temperature distribution in a nozzle guide vane are discussed. Numerical simulation results for the combustor simulator and the nozzle guide vane (NGV) of the first turbine stage are presented. The geometry and flow conditions were defined according to measurements carried out on a test section within the framework of the EU FACTOR (full aerothermal combustor–turbine interactions research) project. The numerical model was validated by a comparison of results against experimental data in the plane at a combustor outlet. Two turbulence models were employed: the Spalart–Allmaras and Explicit Algebraic Reynolds Stress models. It was shown that the NGV potential effect on flow distribution at the combustor–turbine interface located at 42.5% of the axial chord is weak. The clocking effect due to the azimuthal position of guide vanes downstream of the swirlers strongly affects the temperature and flow conditions in a stator cascade.

The Influence of the Boundary Layer State and Reynolds Number on Film Cooling and Heat Transfer on a Cooled Nozzle Guide Vane

2000 ◽  
Author(s):  
Hans Reiss ◽  
Albin Bölcs
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Film Cooling ◽  
Guide Vane ◽  
Suction Side ◽  
Flow Conditions ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Film cooling and heat transfer measurements were carried out on a cooled nozzle guide vane in a linear cascade, using a transient liquid crystal technique. Three flow conditions were realized: the nominal operating condition of the vane with an exit Reynolds number of 1.47e6, as well as two lower flow conditions: Re2L = 1.0e6 and 7.5e5. The vane model was equipped with a single row of inclined round film cooling holes with compound angle orientation on the suction side. Blowing ratios ranging form 0.3 to 1.5 were covered, all using foreign gas injection (CO2) yielding an engine-representative density ratio of 1.6. Two distinct states of the incoming boundary layer onto the injection station were compared, an undisturbed laminar boundary layer as it forms naturally on the suction side, and a fully turbulent boundary layer which was triggered with a trip wire upstream of injection. The aerodynamic flow field is characterized in terms of profile Mach number distribution, and the associated heat transfer coefficients around the uncooled airfoil are presented. Both detailed and spanwise averaged results of film cooling effectiveness and heat transfer coefficients are shown on the suction side, which indicate considerable influence of the state of the incoming boundary layer on the performance of a film cooling row. The influence of the mainstream flow condition on the film cooling behavior at constant blowing ratio is discussed for three chosen injection regimes.

Influence of Upstream Flow Conditions on the Heat Transfer to Nozzle Guide Vanes

1988 ◽  
Vol 110 (3) ◽  
pp. 412-416 ◽  
Author(s):  
V. Krishnamoorthy ◽  
B. R. Pai ◽  
S. P. Sukhatme
Keyword(s):  
Guide Vane ◽  
Gas Temperature ◽  
Flow Conditions ◽  
Cold Flow ◽  
Hot Gas ◽  
Nozzle Guide Vane ◽  
High Turbulence ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Upstream Flow

The influence of a combustor located just upstream of a nozzle guide vane cascade on the heat flux distribution to the nozzle guide vane was experimentally investigated. The surface temperature distribution around the convectively cooled vane of the cascade was obtained by locating the cascade, firstly in a low-turbulence uniform hot gas stream, secondly in a high-turbulence, uniform hot gas stream, and thirdly in a high-turbulence, nonuniform hot gas stream present just downstream of the combustor exit. The results indicate that the increased blade surface temperatures observed for the cascade placed just downstream of the combustor can be accounted for by the prevailing turbulence level measured at cascade inlet in cold-flow conditions and the average gas temperature at the cascade inlet.

Experimental Study of the Flow Field Behind an Annular Turbine Nozzle Guide Vane With and Without Downstream Rotor

1984 ◽  
Author(s):  
E. Boletis ◽  
C. H. Sieverding
Keyword(s):  
Flow Field ◽  
Guide Vane ◽  
Three Dimensional ◽  
Rotor Blades ◽  
Pressure Probe ◽  
Flow Conditions ◽  
Nozzle Guide Vane ◽  
Contour Plots ◽  
Real Flow ◽  
Nozzle Guide

Measurements of the three dimensional flow field in annular turbine nozzle guide vanes present an important step in the simulation of the real flow conditions in turbomachinery bladings. This paper seeks to determine whether the installation of a rotor closely behind a high hub-to-tip ratio cascade (DH/DT=0.8) is indispensable for establishing correct flow conditions at the cascade exit or whether the use of an axial diffuser of a certain length is sufficient. Also, an attempt is made to separate the possible effects of the rotor blades from that of the rotating rotor disc. The tests are carried out on a low speed, low aspect ratio, high turning nozzle guide vane. The flow is explored by means of a double head four-hole pressure probe and the results are presented in the form of contour plots and spanwise pitch-averaged distributions of losses, flow angles and static pressure.

Experimental and Numerical Investigation on the Influence of Trailing Edge Bleeding on the Aerodynamics of a NGV Cascade

2009 ◽  
Author(s):  
Marco Montis ◽  
Reinhard Niehuis ◽  
Mattia Guidi ◽  
Simone Salvadori ◽  
Francesco Martelli ◽  
...  
Keyword(s):  
Guide Vane ◽  
Measured Data ◽  
Flow Conditions ◽  
Trailing Edge ◽  
Pressure Losses ◽  
Ejection Rate ◽  
Nozzle Guide Vane ◽  
Flow Phenomena ◽  
Nozzle Guide ◽  
Good Agreement

A series of tests on a specific designed linear nozzle guide vane (NGV) cascade with trailing edge coolant ejection was carried out to investigate the influence of the trailing edge bleeding (TEB) on the loss behaviour of the profile. Wake traverses with a five-hole probe and measurements of the pressure distribution on the profile were taken varying the ejection rate under reference main flow conditions, namely Re2th = 1.056·106 and Ma2th = 0.8 (Re2th based on the true chord). Wake total pressure losses and isentropic Mach number distributions on the profile were compared to measurements without coolant ejection, showing a significant influence of the TEB both on the wake development and on the flow in the vane passage. Numerical simulations of the experiments showed good agreement with the measured data and provided a deeper understanding of the flow phenomena, revealing the differences in the development of the wake with and without trailing edge coolant ejection and illustrating the blockage effect of the TEB on the flow in the vane passage.

The Extension of a Solution-Adaptive Three-Dimensional Navier–Stokes Solver Toward Geometries of Arbitrary Complexity

1993 ◽  
Vol 115 (2) ◽  
pp. 283-295 ◽  
Author(s):  
W. N. Dawes
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Recent Developments ◽  
Nozzle Guide

This paper describes recent developments to a three-dimensional, unstructured mesh, solution-adaptive Navier–Stokes solver. By adopting a simple, pragmatic but systematic approach to mesh generation, the range of simulations that can be attempted is extended toward arbitrary geometries. The combined benefits of the approach result in a powerful analytical ability. Solutions for a wide range of flows are presented, including a transonic compressor rotor, a centrifugal impeller, a steam turbine nozzle guide vane with casing extraction belt, the internal coolant passage of a radial inflow turbine, and a turbine disk cavity flow.

Flow Measurements in a Nozzle Guide Vane Passage With a Low Aspect Ratio and Endwall Contouring

2000 ◽  
Author(s):  
Steven W. Burd ◽  
Terrence W. Simon
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Guide Vane ◽  
Flow Measurements ◽  
Vast Number ◽  
Aspect Ratios ◽  
Nozzle Guide Vane ◽  
Endwall Contouring ◽  
Nozzle Guide

The vast number of turbine cascade studies in the literature has been performed in straight-endwall, high-aspect-ratio, linear cascades. As a result, there has been little appreciation for the role of, and added complexity imposed by, reduced aspect ratios. There also has been little documentation of endwall profiling at these reduced spans. To examine the role of these factors on cascade hydrodynamics, a large-scale nozzle guide vane simulator was constructed at the Heat Transfer Laboratory of the University of Minnesota. This cascade is comprised of three airfoils between one contoured and one flat endwall. The geometries of the airfoils and endwalls, as well as the experimental conditions in the simulator, are representative of those in commercial operation. Measurements with hot-wire anemometry were taken to characterize the flow approaching the cascade. These measurements show that the flow field in this cascade is highly elliptic and influenced by pressure gradients that are established within the cascade. Exit flow field measurements with triple-sensor anemometry and pressure measurements within the cascade indicate that the acceleration imposed by endwall contouring and airfoil turning is able to suppress the size and strength of key secondary flow features. In addition, the flow field near the contoured endwall differs significantly from that adjacent to the straight endwall.

A Method for Correlating the Influence of External Crossflow on the Discharge Coefficients of Film Cooling Holes

2000 ◽  
Vol 123 (2) ◽  
pp. 258-265 ◽  
Author(s):  
D. A. Rowbury ◽  
M. L. G. Oldfield ◽  
G. D. Lock
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Guide Vane ◽  
Discharge Coefficients ◽  
Nozzle Guide Vane ◽  
Aero Engine ◽  
Nozzle Guide ◽  
Film Cooling Holes ◽  
Asme Paper

An empirical means of predicting the discharge coefficients of film cooling holes in an operating engine has been developed. The method quantifies the influence of the major dimensionless parameters, namely hole geometry, pressure ratio across the hole, coolant Reynolds number, and the freestream Mach number. The method utilizes discharge coefficient data measured on both a first-stage high-pressure nozzle guide vane from a modern aero-engine and a scale (1.4 times) replica of the vane. The vane has over 300 film cooling holes, arranged in 14 rows. Data was collected for both vanes in the absence of external flow. These noncrossflow experiments were conducted in a pressurized vessel in order to cover the wide range of pressure ratios and coolant Reynolds numbers found in the engine. Regrettably, the proprietary nature of the data collected on the engine vane prevents its publication, although its input to the derived correlation is discussed. Experiments were also conducted using the replica vanes in an annular blowdown cascade which models the external flow patterns found in the engine. The coolant system used a heavy foreign gas (SF6 /Ar mixture) at ambient temperatures which allowed the coolant-to-mainstream density ratio and blowing parameters to be matched to engine values. These experiments matched the mainstream Reynolds and Mach numbers and the coolant Mach number to engine values, but the coolant Reynolds number was not engine representative (Rowbury, D. A., Oldfield, M. L. G., and Lock, G. D., 1997, “Engine-Representative Discharge Coefficients Measured in an Annular Nozzle Guide Vane Cascade,” ASME Paper No. 97-GT-99, International Gas Turbine and Aero-Engine Congress & Exhibition, Orlando, Florida, June 1997; Rowbury, D. A., Oldfield, M. L. G., Lock, G. D., and Dancer, S. N., 1998, “Scaling of Film Cooling Discharge Coefficient Measurements to Engine Conditions,” ASME Paper No. 98-GT-79, International Gas Turbine and Aero-Engine Congress & Exhibition, Stockholm, Sweden, June 1998). A correlation for discharge coefficients in the absence of external crossflow has been derived from this data and other published data. An additive loss coefficient method is subsequently applied to the cascade data in order to assess the effect of the external crossflow. The correlation is used successfully to reconstruct the experimental data. It is further validated by successfully predicting data published by other researchers. The work presented is of considerable value to gas turbine design engineers as it provides an improved means of predicting the discharge coefficients of engine film cooling holes.

Influence of Pre-History and Leading Edge Contouring on Aero-Performance of a 3D Nozzle Guide Vane

2013 ◽  
Author(s):  
Ranjan Saha ◽  
Boris I. Mamaev ◽  
Jens Fridh ◽  
Björn Laumert ◽  
Torsten H. Fransson
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Stagnation Line ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Turbine Vane ◽  
Loss Coefficients ◽  
Exit Mach Number ◽  
Nozzle Guide

Experiments are conducted to investigate the effect of the pre-history in the aerodynamic performance of a three-dimensional nozzle guide vane with a hub leading edge contouring. The performance is determined with two pneumatic probes (5 hole and 3 hole) concentrating mainly on the endwall. The investigated vane is a geometrically similar gas turbine vane for the first stage with a reference exit Mach number of 0.9. Results are compared for the baseline and filleted cases for a wide range of operating exit Mach numbers from 0.5 to 0.9. The presented data includes loading distributions, loss distributions, fields of exit flow angles, velocity vector and vorticity contour, as well as, mass-averaged loss coefficients. The results show an insignificant influence of the leading edge fillet on the performance of the vane. However, the pre-history (inlet condition) affects significantly in the secondary loss. Additionally, an oil visualization technique yields information about the streamlines on the solid vane surface which allows identifying the locations of secondary flow vortices, stagnation line and saddle point.

Effects of Endwall Film Coolant Flow Rate on Secondary Flows and Coolant Mixing in a First Stage Nozzle Guide Vane

2021 ◽  
Author(s):  
Mahmood Alqefl ◽  
Kedar Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong Kim ◽  
...  
Keyword(s):  
Flow Rate ◽  
Guide Vane ◽  
Secondary Flows ◽  
Coolant Flow ◽  
Coolant Flow Rate ◽  
Nozzle Guide Vane ◽  
Nozzle Guide
Sign in / Sign up

Export Citation Format

Share Document