scholarly journals Small-Scale Static Fire Tests of 3D Printing Hybrid Rocket Fuel Grains Produced from Different Materials

Aerospace ◽  
2019 ◽  
Vol 6 (7) ◽  
pp. 81 ◽  
Author(s):  
McFarland ◽  
Antunes
Keyword(s):  
3D Printing ◽  
Polyethylene Terephthalate ◽  
New Technologies ◽  
Acrylonitrile Butadiene Styrene ◽  
Small Scale ◽  
Fire Tests ◽  
Hybrid Rocket ◽  
Fused Deposition ◽  
Low Earth Orbits ◽  
Butadiene Styrene

The last decade has seen an almost exponential increase in the number of rocket launches for sounding missions or for delivering payloads into low Earth orbits. The emergence of new technologies like rapid prototyping, including 3D printing, is changing the approach to rocket motor design. This project conducted a series of small-scale static fire tests of fused deposition manufacturing hybrid rocket motors that were designed to explore the performance of a variety of commonly available fused deposition manufacturing materials. These materials included acrylonitrile butadiene styrene, acrylonitrile styrene acrylate, polylactic acid (PLA), polypropylene, polyethylene terephthalate glycol, Nylon, and AL (PLA with aluminum particles). To test the performance of small-scale fuel grains, a modular apparatus with a range of sensors fitted to it was designed and manufactured. The small-scale testing performed static burns on two fuel grains of each material with initial dimensions of 100 mm long and 20 mm in diameter with a 6 mm straight circular combustion port. The focus of this study was mainly on the regression rates of each material of fuel grains. Acrylonitrile styrene acrylate and Nylon showed the highest regression rates, while the polyethylene terephthalate glycol regression rates were relatively poor. Also, the acrylonitrile butadiene styrene and acrylonitrile styrene acrylate demonstrating relatively high regression rates when compared to existing hybrid fuels like hydroxyl-terminated polybutadiene.

Tensile Strength and Flexural Strength Testing of Acrylonitrile Butadiene Styrene (ABS) Materials for Biomimetic Robotic Applications

2014 ◽  
Vol 20 ◽  
pp. 11-21 ◽  
Author(s):  
Tran Linh Khuong ◽  
Zhao Gang ◽  
Muhammad Farid ◽  
Rao Yu ◽  
Zhuang Zhi Sun ◽  
...  
Keyword(s):  
Tensile Strength ◽  
3D Printing ◽  
Rapid Prototyping ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Butadiene Styrene

Biomimetic robots borrow their structure, senses and behavior from animals, such as humans or insects, and plants. Biomimetic design is design ofa machine, a robot or a system in engineeringdomain thatmimics operational and/orbehavioral model of a biological system in nature. 3D printing technology has another name as rapid prototyping technology. Currently it is being developed fastly and widely and is applied in many fields like the jewelry, footwear, industrial design, architecture, engineering and construction, automotive, aerospace, dental and medical industry, education, geographic information system, civil engineering, guns. 3D printing technology is able to manufacture complicated, sophisticated details that the traditional processing method cannot manufacture. Therefore, 3D printing technology can be seen as an effective tool in biomimetic, which can accurately simulate most of the biological structure. Fused Deposition Modeling (FDM) is a technology of the typical rapid prototyping. The main content of the article is the focusing on tensile strength test of the ABS-Acrylonitrile Butadiene Styrene material after using Fused Deposition Modeling (FDM) technology, concretization after it’s printed by UP2! 3D printer. The article focuses on two basic features which are Tensile Strength and Determination of flexural properties.

scholarly journals Modelling and Investigation of Crack Growth for 3D-Printed Acrylonitrile Butadiene Styrene (ABS) with Various Printing Parameters and Ambient Temperatures

Polymers ◽  
2021 ◽  
Vol 13 (21) ◽  
pp. 3737
Author(s):  
Yousef Lafi A. Alshammari ◽  
Feiyang He ◽  
Muhammad A. Khan
Keyword(s):  
3D Printing ◽  
Crack Growth ◽  
Three Dimensional ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition Modelling ◽  
Structural Dynamic ◽  
Fused Deposition ◽  
Nozzle Size ◽  
Printing Parameters ◽  
Butadiene Styrene

Three-dimensional (3D) printing is one of the significant industrial manufacturing methods in the modern era. Many materials are used for 3D printing; however, as the most used material in fused deposition modelling (FDM) technology, acrylonitrile butadiene styrene (ABS) offers good mechanical properties. It is perfect for making structures for industrial applications in complex environments. Three-dimensional printing parameters, including building orientation, layers thickness, and nozzle size, critically affect the crack growth in FDM structures under complex loads. Therefore, this paper used the dynamic bending vibration test to investigate their influence on fatigue crack growth (FCG) rate under dynamic loads and the Paris power law constant C and m. The paper proposed an analytical solution to determine the stress intensity factor (SIF) at the crack tip based on the measurement of structural dynamic response. The experimental results show that the lower ambient temperature, as well as increased nozzle size and layer thickness, provide a lower FCG rate. The printing orientation, which is the same as loading, also slows the crack growth. The linear regression between these parameters and Paris Law’s coefficient also proves the same conclusion.

scholarly journals Biomaterials: Polylactic Acid and 3D Printing Processes for Orthosis and Prosthesis

2017 ◽  
Vol 54 (1) ◽  
pp. 98-102 ◽  
Author(s):  
Roxana Miclaus ◽  
Angela Repanovici ◽  
Nadinne Roman
Keyword(s):  
3D Printing ◽  
Polylactic Acid ◽  
Medical Devices ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition ◽  
The Past ◽  
Deposition Modeling ◽  
Printing Processes ◽  
Butadiene Styrene

Since the development of 3D printing, over the past decades, the domain of application has evolved significantly! Concerning the orthosis and prosthesis manufacturing, the 3D printing offers many possibilities for developing new medical devices for people with disabilities. Our paper wish to synthetize the main 3D printing methods and the biomaterial properties which can be used in orthosis and prosthesis manufacturing, like polylactic acid or acrylonitrile butadiene styrene. Fused Deposition Modeling and Stereo lithography are most used for medical devices manufacturing and usually using polylactic acid, considering the properties of this polymer and de organic componence.

Izod Impact Strength of Acrylonitrile Butadiene Styrene (ABS) Matetials after Used in UP2! 3D-Printer

2015 ◽  
Vol 713-715 ◽  
pp. 2737-2740 ◽  
Author(s):  
Tran Linh Khuong ◽  
Zhao Gang ◽  
Muhammad Farid ◽  
Rao Yu
Keyword(s):  
3D Printing ◽  
Impact Strength ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition ◽  
Izod Impact Strength ◽  
Deposition Modeling ◽  
Izod Impact ◽  
Exact Calculations ◽  
Butadiene Styrene

3D printing technology which is also named as fast prototypinghas shown excellent resultsto manufacture more complex and sophiscated products;hence is increasingly being developed and widely applied. Fused Deposition Modeling (FDM) is one of the most popular 3D printing techniques available today because it's simple and easy to make, these cheap printers nowadays are using this technology. Acrylonitrile Butadiene Styrene (ABS) is the material which is most commonly used among three kinds of common materials of FDM technology ABS, PLA, PVA. To design a patternfor using FDM technology using the printer UP2in particular, the exact calculations and the mechanical properties of the material ABS are required.The article focuses on testing the Izod impact strength.

scholarly journals Development and Mechanical Properties of Basalt Fiber-Reinforced Acrylonitrile Butadiene Styrene for In-Space Manufacturing Applications

2019 ◽  
Vol 3 (3) ◽  
pp. 89 ◽  
Author(s):  
Natalie Coughlin ◽  
Bradley Drake ◽  
Mikala Fjerstad ◽  
Easton Schuster ◽  
Tyler Waege ◽  
...  
Keyword(s):  
3D Printing ◽  
Flexural Modulus ◽  
Basalt Fiber ◽  
Acrylonitrile Butadiene Styrene ◽  
Small Scale ◽  
X Rays ◽  
Fiber Reinforced ◽  
Basalt Fibers ◽  
The Cost ◽  
Butadiene Styrene

A new basalt fiber reinforced acrylonitrile butadiene styrene (ABS) filament has been developed for fused filament fabrication (FFF, 3D printing) to be used in Mars habitat construction. Building habitats on Mars will be expensive, especially if all material must be shipped from earth. However, if some materials can be used from Mars, costs will dramatically decrease. Basalt is easily mined from the surface of Mars. This study details the production process of the material, experimental results from mechanical testing, and preliminary X-ray shielding characteristics. The addition of chopped 3 mm basalt fibers to standard FFF material, ABS, increased strength and stiffness of the composite material. By adding 25% (by weight) basalt fiber to ABS, tensile strength improved nearly 40% by increasing from 36.55 MPa to 50.58 MPa, while Modulus of Elasticity increased about 120% from 2.15 GPa to 4.79 GPa. Flexural strength increased by about 20% from 56.94 MPa to 68.51 MPa, while Flexural Modulus increased by about 70% from 1.81 GPa to 3.05 GPa. While compression results did not see much strength improvements, the addition of fibers also did not decrease compressive strength. This is important when considering that basalt fibers provide radiation shielding and the cost of adding basalt fibers to construction materials on Mars will be negligible compared to the cost of shipping other materials from earth. In preliminary digital radiography testing, it was shown that 77% of X-rays were shielded with 25% basalt fiber added (as compared to neat ABS). In small-scale 3D printing applications, the 25% fiber ratio seems to be the highest ratio that provides reliable FFF printing.

Evaluation of a rapid prototyping application for stomas

2020 ◽  
Vol 26 (9) ◽  
pp. 1525-1533 ◽  
Author(s):  
Jose Manuel Sierra ◽  
Jose Ignacio Rodríguez ◽  
Marta María Villazon ◽  
Jose Luis Cortizo ◽  
Maria del Rocio Fernandez
Keyword(s):  
3D Printing ◽  
Acrylonitrile Butadiene Styrene ◽  
Experimental Tests ◽  
Fused Deposition Modelling ◽  
Static Loads ◽  
Content Type ◽  
Fused Deposition ◽  
Collection Device ◽  
Low Costs ◽  
Butadiene Styrene

Purpose This paper aims to describe the development of an internal waste-collection device for patients who have undergone a colostomy or ileostomy. Its design is based on devices that have been produced by 3D printing with acrylonitrile butadiene styrene. The aim is to find an alternative to the external bags that these patients currently use and to evaluate the properties of the device produced by additive manufacturing. Design/methodology/approach Software for solid modelling has been used, and virtual models allow its visualization and animation, for evaluation, in a simple and fast way. Subsequently, functional prototypes have been developed by a multidisciplinary team, which includes surgeons and engineers, and have been tested to verify their mechanical properties and suitability for function. Findings The project has developed a functional design that has been patented and is in the clinical trials phase. This study demonstrates how 3D printing technologies are the perfect complement to accelerate the design process and build functional prototypes at low costs. The experimental tests regarding cytotoxicity, printing orientation, dynamic and static loads and temperature resistance have demonstrated the validity of the proposed device. Originality/value A device for internal pouch in colostomized patients has been designed, manufactured by fused deposition modelling and validated.

scholarly journals 3D Printing of Mini Tablets for Pediatric Use

2021 ◽  
Vol 14 (2) ◽  
pp. 143
Author(s):  
Julius Krause ◽  
Laura Müller ◽  
Dorota Sarwinska ◽  
Anne Seidlitz ◽  
Malgorzata Sznitowska ◽  
...  
Keyword(s):  
3D Printing ◽  
Fused Deposition Modeling ◽  
Dosage Forms ◽  
Small Scale ◽  
Fused Deposition ◽  
On Demand ◽  
Pediatric Diseases ◽  
Deposition Modeling ◽  
Manufacturing Techniques ◽  
Pediatric Use

In the treatment of pediatric diseases, suitable dosages and dosage forms are often not available for an adequate therapy. The use of innovative additive manufacturing techniques offers the possibility of producing pediatric dosage forms. In this study, the production of mini tablets using fused deposition modeling (FDM)-based 3D printing was investigated. Two pediatric drugs, caffeine and propranolol hydrochloride, were successfully processed into filaments using hyprolose and hypromellose as polymers. Subsequently, mini tablets with diameters between 1.5 and 4.0 mm were printed and characterized using optical and thermal analysis methods. By varying the number of mini tablets applied and by varying the diameter, we were able to achieve different release behaviors. This work highlights the potential value of FDM 3D printing for the on-demand production of patient individualized, small-scale batches of pediatric dosage forms.

Influence of Part Orientation on the Surface Roughness in the Process of Fused Deposition Modeling

2021 ◽  
Vol 896 ◽  
pp. 29-37
Author(s):  
Ján Milde ◽  
František Jurina ◽  
Jozef Peterka ◽  
Patrik Dobrovszký ◽  
Jakub Hrbál ◽  
...  
Keyword(s):  
Surface Roughness ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
Orientation Angle ◽  
Acrylonitrile Butadiene Styrene ◽  
Lower Surface ◽  
Geometrical Model ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Part Orientation

The article focused on the influence of part orientation on the surface roughness of cuboid parts during the process of fabricating by FDM technology. The components, in this case, is simple cuboid part with the dimensions 15 mm x 15mm x 30 mm. A geometrical model is defined that considers the shape of the material filaments after deposition, to define a theoretical roughness profile, for a certain print orientation angle. Five different print orientations in the X-axis of the cuboid part were set: 0°, 30°, 45°, 60°, and 90°. According to previous research in the field of FDM technology by the author, the internal structure (infill) was set at the value of 70%. The method of 3D printing was the Fused Deposition Modeling (FDM) and the material used in this research was thermoplastic ABS (Acrylonitrile butadiene styrene). For each setting, there were five specimens (twenty five prints in total). Prints were fabricated on a Zortrax M200 3D printer. After the 3D printing, the surface “A” was investigated by portable surface roughness tester Mitutoyo SJ-210. Surface roughness in the article is shown in the form of graphs (Fig.7). Results show increase in part roughness with increasing degree of part orientation. When the direction of applied layers on the measured surface was horizontal, significant improvement in surface roughness was observed. Findings in this paper can be taken into consideration when designing parts, as they can contribute in achieving lower surface roughness values.

Sign in / Sign up

Export Citation Format

Share Document