scholarly journals Three Dimensional CFD Studies of a Solar Chimney: Effect of Geometrical Parameters and Diurnal Variations on Power Generated

2020 ◽  
Vol 2 ◽  
Author(s):  
Arijit A. Ganguli ◽  
Sagar Deshpande
Keyword(s):  
Three Dimensional ◽  
Diurnal Variations ◽  
Geometrical Parameters ◽  
Solar Chimney ◽  
Chimney Effect

scholarly journals Radial Turbine Design for Solar Chimney Power Plants

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 674
Author(s):  
Paul Caicedo ◽  
David Wood ◽  
Craig Johansen
Keyword(s):  
Power Plants ◽  
Reference Frames ◽  
Three Dimensional ◽  
Discrete Ordinates ◽  
Large Area ◽  
Solar Chimney ◽  
Cfd Simulations ◽  
Radial Turbine ◽  
Design Changes ◽  
Turbine Design

Solar chimney power plants (SCPPs) collect air heated over a large area on the ground and exhaust it through a turbine or turbines located near the base of a tall chimney to produce renewable electricity. SCPP design in practice is likely to be specific to the site and of variable size, both of which require a purpose-built turbine. If SCPP turbines cannot be mass produced, unlike wind turbines, for example, they should be as cheap as possible to manufacture as their design changes. It is argued that a radial inflow turbine with blades made from metal sheets, or similar material, is likely to achieve this objective. This turbine type has not previously been considered for SCPPs. This article presents the design of a radial turbine to be placed hypothetically at the bottom of the Manzanares SCPP, the only large prototype to be built. Three-dimensional computational fluid dynamics (CFD) simulations were used to assess the turbine’s performance when installed in the SCPP. Multiple reference frames with the renormalization group k-ε turbulence model, and a discrete ordinates non-gray radiation model were used in the CFD simulations. Three radial turbines were designed and simulated. The largest power output was 77.7 kW at a shaft speed of 15 rpm for a solar radiation of 850 W/m2 which exceeds by more than 40 kW the original axial turbine used in Manzanares. Further, the efficiency of this turbine matches the highest efficiency of competing turbine designs in the literature.

scholarly journals Energy Loss in Steep Open Channels with Step-Pools

Water ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 72
Author(s):  
Suresh Kumar Thappeta ◽  
S. Murty Bhallamudi ◽  
Venu Chandra ◽  
Peter Fiener ◽  
Abul Basar M. Baki
Keyword(s):  
Energy Loss ◽  
Flow Rate ◽  
Recirculation Zone ◽  
Three Dimensional ◽  
Nonlinear Function ◽  
Open Channels ◽  
Geometrical Parameters ◽  
Transition Flow ◽  
Cumulative Energy ◽  
Zone Velocity

Three-dimensional numerical simulations were performed for different flow rates and various geometrical parameters of step-pools in steep open channels to gain insight into the occurrence of energy loss and its dependence on the flow structure. For a given channel with step-pools, energy loss varied only marginally with increasing flow rate in the nappe and transition flow regimes, while it increased in the skimming regime. Energy loss is positively correlated with the size of the recirculation zone, velocity in the recirculation zone and the vorticity. For the same flow rate, energy loss increased by 31.6% when the horizontal face inclination increased from 2° to 10°, while it decreased by 58.6% when the vertical face inclination increased from 40° to 70°. In a channel with several step-pools, cumulative energy loss is linearly related to the number of step-pools, for nappe and transition flows. However, it is a nonlinear function for skimming flows.

Prediction of internal geometry and tensile behavior of 3D woven solid structures by mathematical coding

2021 ◽  
pp. 152808372110013
Author(s):  
Vivek R Jayan ◽  
Lekhani Tripathi ◽  
Promoda Kumar Behera ◽  
Michal Petru ◽  
BK Behera
Keyword(s):  
Volume Fraction ◽  
Three Dimensional ◽  
Areal Density ◽  
Woven Fabrics ◽  
Tensile Behavior ◽  
Geometrical Parameters ◽  
Fiber Volume ◽  
Acceptable Error ◽  
Internal Geometry ◽  
Unit Cells

The internal geometry of composite material is one of the most important factors that influence its performance and service life. A new approach is proposed for the prediction of internal geometry and tensile behavior of the 3 D (three dimensional) woven fabrics by creating the unit cell using mathematical coding. In many technical applications, textile materials are subjected to rates of loading or straining that may be much greater in magnitude than the regular household applications of these materials. The main aim of this study is to provide a generalized method for all the structures. By mathematical coding, unit cells of 3 D woven orthogonal, warp interlock and angle interlock structures have been created. The study then focuses on developing code to analyze the geometrical parameters of the fabric like fabric thickness, areal density, and fiber volume fraction. Then, the tensile behavior of the coded 3 D structures is studied in Ansys platform and the results are compared with experimental values for authentication of geometrical parameters as well as for tensile behavior. The results show that the mathematical coding approach is a more efficient modeling technique with an acceptable error percentage.

Three-dimensional computational study in a corrugated pipe inserted system filled with phase change material

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ömer Akbal ◽  
Hakan F. Öztop ◽  
Nidal H. Abu-Hamdeh
Keyword(s):  
Phase Change ◽  
Phase Change Material ◽  
Computational Analysis ◽  
Computational Study ◽  
Three Dimensional ◽  
Simple Algorithm ◽  
Melting Time ◽  
Geometrical Parameters ◽  
Content Type ◽  
Change Material

Purpose The purpose of this paper is to make a three-dimensional computational analysis of melting in corrugated pipe inserted system filled with phase change material (PCM). The system was heated from the inner pipe, and temperature of the outer pipe was lower than that of inner pipe. Different geometrical ratio cases and two different temperature differences were tested for their effect on melting time. Design/methodology/approach A computational analysis through a pipe with corrugated pipe filled with PCM is analyzed. Finite volume method was applied with the SIMPLE algorithm method to solve the governing equations. Findings The results indicate that the geometrical parameters can be used to control the melting time inside the heat exchanger which, in turn, affect the energy efficiency. The fastest melting time is seen in Case 4 at the same temperature difference which is the major observation of the current work. Originality/value Originality of this work is to perform a three-dimensional analysis of melting of PCM in a corrugated pipe inserted pipe.

scholarly journals Fully three-dimensional analysis of a photonic crystal assisted silicon on insulator waveguide bend

2018 ◽  
Vol 32 (31) ◽  
pp. 1850344 ◽  
Author(s):  
N. Eti ◽  
Z. Çetin ◽  
H. S. Sözüer
Keyword(s):  
Photonic Crystal ◽  
Numerical Study ◽  
Fdtd Method ◽  
Three Dimensional ◽  
Silicon On Insulator ◽  
Geometrical Parameters ◽  
Low Loss ◽  
Bending Loss ◽  
Difference Time ◽  
Waveguide Bend

A detailed numerical study of low-loss silicon on insulator (SOI) waveguide bend is presented using the fully three-dimensional (3D) finite-difference time-domain (FDTD) method. The geometrical parameters are optimized to minimize the bending loss over a range of frequencies. Transmission results for the conventional single bend and photonic crystal assisted SOI waveguide bend are compared. Calculations are performed for the transmission values of TE-like modes where the electric field is strongly transverse to the direction of propagation. The best obtained transmission is over 95% for TE-like modes.

scholarly journals Digital methods for measuring grain size parameters of aggregate–binder mixtures.

2013 ◽  
Vol 47 (4) ◽  
pp. 1834
Author(s):  
E. Profitis ◽  
D. Kapatos ◽  
E. Chatzitheodoridis ◽  
D. Xirouchakis ◽  
C. Loupasakis
Keyword(s):  
Three Dimensional ◽  
Two Dimensions ◽  
Geometrical Parameters ◽  
Bituminous Mixtures ◽  
Dimensional Measurements ◽  
Digital Methods ◽  
Significant Cost Reduction ◽  
Future Work ◽  
Grain Size Parameters ◽  
Exact Separation

Geometrical parameters of natural and crushed aggregates such as grain length, perimeter, area, etc., underline the shape and flakiness indices definition. The latter indices have a measurable effect on the mechanical properties of aggregates–binder mixtures, e.g. concrete, mortar, bituminous mixtures. In this work, digital methods were developed with the mathematical software Matlab, by applying a statistical method called k-means clustering for the exact separation between background and aggregates to compute the aforementioned properties. The overall code can be applied in real time by analysing quickly a large volume of data with accuracy and significant cost reduction. Currently, only the two dimensions of the grains could be measured. Future work will focus on full three-dimensional measurements by comparing paired images taken from different angles but also aggregate segmentation in case of touching particles.

scholarly journals Scale effect in a fluid-conducting fault network

2019 ◽  
Vol 61 (4) ◽  
pp. 3-14
Author(s):  
V. A. Petrov ◽  
M. Lespinasse ◽  
V. V. Poluektov ◽  
S. A. Ustinov ◽  
V. A. Minaev
Keyword(s):  
Pore Space ◽  
Three Dimensional ◽  
Transport Processes ◽  
Geometrical Parameters ◽  
Fluid Filtration ◽  
Ore Formation ◽  
Fracture Systems ◽  
Eastern Transbaikalia ◽  
Scale Levels ◽  
Fault Network

The data presented in the article consistently outlines the methodology for studying the orientation and morphogenetic characteristics of fracture systems of four scale levels including kilometers, meters, centimeters and millimeters. The Urtuisky granite massif, located in the South-Eastern Transbaikalia to the west of the Streltsovsky caldera, containing uranium deposits unique in their reserves was chosen as the object of the research. The massif is composed of Late Riphean granites and granite-gneisses, affected by dynamometamorphic and hydrothermal-metasomatic transformations in various degrees, and dissected by numerous faults with traces of fluid activity of various tectogenesis episodes. The interrelation between such geometrical parameters of fractures systems as specific density and specific length was established. It is shown that such geostructural data should be used for conceptual and numerical modeling of fluid filtration and radionuclides transport processes occurring in a three-dimensional fractured-pore space of crystalline rocks, as applied to the reconstruction and modeling of uranium ore formation and use of geological space for radioactive materials isolation.

scholarly journals A Multi-Fidelity Model for Simulations and Sensitivity Analysis of Piezoelectric Inkjet Printheads

Micromachines ◽  
2021 ◽  
Vol 12 (9) ◽  
pp. 1038
Author(s):  
Vinh-Tan Nguyen ◽  
Jason Yu Chuan Leong ◽  
Satoshi Watanabe ◽  
Toshimitsu Morooka ◽  
Takayuki Shimizu
Keyword(s):  
Sensitivity Analysis ◽  
Three Dimensional ◽  
Element Model ◽  
Geometrical Parameters ◽  
Generation Process ◽  
Mechanical Coupling ◽  
Design Variables ◽  
Computational Structural Mechanics ◽  
Lumped Element Model ◽  
Inkjet Printhead

The ink drop generation process in piezoelectric droplet-on-demand devices is a complex multiphysics process. A fully resolved simulation of such a system involves a coupled fluid–structure interaction approach employing both computational fluid dynamics (CFD) and computational structural mechanics (CSM) models; thus, it is computationally expensive for engineering design and analysis. In this work, a simplified lumped element model (LEM) is proposed for the simulation of piezoelectric inkjet printheads using the analogy of equivalent electrical circuits. The model’s parameters are computed from three-dimensional fluid and structural simulations, taking into account the detailed geometrical features of the inkjet printhead. Inherently, this multifidelity LEM approach is much faster in simulations of the whole inkjet printhead, while it ably captures fundamental electro-mechanical coupling effects. The approach is validated with experimental data for an existing commercial inkjet printhead with good agreement in droplet speed prediction and frequency responses. The sensitivity analysis of droplet generation conducted for the variation of ink channel geometrical parameters shows the importance of different design variables on the performance of inkjet printheads. It further illustrates the effectiveness of the proposed approach in practical engineering usage.

Geometry and respiratory displacement of human ribs

1987 ◽  
Vol 62 (5) ◽  
pp. 1872-1877 ◽  
Author(s):  
T. A. Wilson ◽  
K. Rehder ◽  
S. Krayer ◽  
E. A. Hoffman ◽  
C. G. Whitney ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Geometrical Parameters ◽  
Small Component ◽  
X Ray ◽  
Lung Capacity ◽  
Circular Arcs ◽  
Residual Capacity ◽  
X Ray Computed ◽  
Best Fit ◽  
Bucket Handle

The three-dimensional coordinates of points in the ribs of two supine relaxed males, holding their breath at functional residual capacity (FRC) and with their glottis closed at total lung capacity (TLC), were obtained from volumetric X-ray computed tomographical images. The orientation of planes that best fit the data for each rib at each lung volume and the circular arcs that fit the points in the planes of the ribs were determined, and average values of these geometrical parameters for ribs 3–7 are reported. The planes of the ribs at TLC can be described as displaced from the planes at FRC by a rotation about an axis that passes near the spine. The pump handle and bucket handle components of rotation are 11 and 13 degrees, respectively, for rib 3 and both decrease with increasing rib number to 7 and 10 degrees at rib 7. The angles between the axes of rotation and the midplane are approximately 35 degrees for all 5 ribs. The radii of the circular arcs fit to the data at TLC are slightly larger than those at FRC, and this suggests that there is a small component of rotation normal to the plane of the rib.

Experimental and Theoretical Investigation of Performance of a Solar Chimney Model Part II: Model Development and Validation

2021 ◽  
Vol 5 (2) ◽  
Author(s):  
Ibrahim A Abuashe ◽  
Bashir H Arebi ◽  
Essaied M Shuia
Keyword(s):  
Mathematical Model ◽  
Power Output ◽  
Model Development ◽  
Geometrical Parameters ◽  
Balance Equations ◽  
Solar Chimney ◽  
And Performance ◽  
Development And Validation ◽  
The Mathematical Model ◽  
Good Agreement

A mathematical model based on the momentum, continuity and energy balance equations was developed to simulate the behavior of the air flow inside the solar chimney system. The model can estimate the power output and performance of solar chimney systems. The developed mathematical model is validated by the experimental data that were collected from small pilot solar chimney; (experiment was presented in part I). Good agreement was obtained between the experimental results and that from the mathematical model. The model can be used to analyze the solar chimney systems and to determine the effect of geometrical parameters such as chimney height and collector diameter on the power output and the efficiency of the system

Sign in / Sign up

Export Citation Format

Share Document