scholarly journals Effect of aggregates and curing conditions on the compressive strength of concrete with age

2010 ◽  
Vol 1 (2) ◽  
pp. 1-6 ◽  
Author(s):  
Aminur M.R ◽  
Harunur M.R ◽  
Teo D.C.L ◽  
Abu Zakir M.M

The present research describes the effect of aggregate and curing condition on the compressive strength of concrete with age. Ordinary Portland cement, coarse sand and brick chips/pebble gravels were used as binder, fine aggregate and coarse aggregate respectively. The ratio of cement, sand and coarse aggregate was 1:2:4 by weight. Five different curing conditions namely, water curing (WC), self curing (SC), air dry curing (ADC), one-day delay curing (1-DC) and three-days delay curing (3-DC) were employed. Two types of concrete namely; concrete C1 (brick chips as coarse aggregate) and C2 (pebbles gravel as coarse aggregate) were prepared in this study. The physical and mechanical properties of aggregates and concrete were determined respectively. The results show that, the compressive strength of concrete is affected by the properties of the aggregate and also curing condition employed. It was found that, the concrete C1 and the normal water curing appeared to be better than concrete C2 and other types of curing condition.

2021 ◽  
Vol 11 (2) ◽  
pp. 127-136
Author(s):  
Sadaf Noshin ◽  
M. Adil Khan ◽  
M. Salman ◽  
M. Shahzad Aslam ◽  
Haseeb Ahmad ◽  
...  

Abstract In construction industry, demolished construction waste is recently used as reprocessed aggregate to produce environmentally friendly concrete which is a good substitute to normal crush due to increased demand of ecological growth and conservation benefits. Though, the properties of recycled aggregate concrete are smallest as compared to concrete produced from natural aggregate and these properties can be enhanced by adding some materials having cementitious properties. Rice husk ash (RHA) is used as partial replacement of cement in recycled aggregate concrete to improve the properties as well as to conserve the natural resources. The elementary purpose of this investigation is to determine the compressive strength of concrete by the replacement of cement with different percentages of rice husk ash such as 0%, 7.5%, 10%, 12.5%, 15%, and 17.5% respectively with different curing conditions. For the experimental program approximate 198 cylinders (18 for rapid curing, 90 for normal water curing and 90 for acid curing) are casted with the mix proportion of 1:2:4 and water to cement ratio of 0.50 whereas curing is done at the ages of 3,7,14,21 and 28 days. Various experiments are performed on fresh and hardened concrete to determine the effects of rice husk ash on recycled aggregate concrete with different curing conditions. Linear regression analysis is carried out to determine the compressive strength of concrete. It is pragmatic from the slump test results that the workability of recycled aggregate concrete is decreased by increasing the quantity of rice husk ash. This reduction in slump is due to high water absorption of recycled aggregates and rice husk ash. Further, the compressive strength of recycled aggregate concrete with normal and acid curing is decreased by increasing the percentages of rice husk ash. It is also observed that at 28- days of normal water curing for mix M1,M2,M3,M4,M5 and M6 the compressive strength is increased by 0.96%, 2.74% 1.45%,4.50%,4.23% and 4.22% respectively as compared to the compressive strength values at 28 days of acid water curing. Therefore, it is concluded that recycled aggregate concrete with 10 to 12% of rice husk ash is suitable for properties of concrete. The acid water curing has negative impacts on hardened properties of concrete as it reduced the compressive strength of concrete as compared to normal water curing.


2021 ◽  
Vol 1 (1) ◽  
pp. 1
Author(s):  
Agung Prayogi

Abstract Concrete is the most widely used material throughout the world and innovations continue to be carried out to produce efficient development. Shell charcoal ash and rice husk ash are industrial by-products which have the potential to replace sand for concrete mix, especially in Indragiri Hilir. The research with the title "Effect of Mixture of Rice Husk Ash and Shell Ash Ashes as Substitute for Some Fine Aggregates Against Concrete Compressive Strength" aims to prove the effect of a mixture of shell charcoal ash and husk ash to replace some of the sand to produce maximum compressive strength. Concrete is a mixture of Portland cement, fine aggregate, coarse aggregate, and water. This research uses 5 variations of the mixture to the weight of sand, BSA 0 without a substitute mixture, BSA 1 with a mixture of 5% husk ash and 10% shell charcoal, BSA 2 with a mixture of 5% husk ash and 15% charcoal ash, BSA 3 with a mixture of 5% husk ash and 18% charcoal, BSA 4 with a mixture of 10% husk and 10% charcoal, and BSA 5 with a mixture of 13% husk ash and 10% charcoal ash. SNI method is used for the Job Mix Formula (JMF) mixture in this research. The results of the average compressive strength of concrete at 28 days for JMF of 21.05 MPa, BSA 1 of 23.68 MPa, BSA 2 of 22.23 MPa, BSA 3 of 14.39 MPa, BSA 4 of 13.34 MPa , and BSA 5 of 20.14 MPa. The conclusion drawn from the results of the BSA 1 research with a mixture of 5% husk ash and 15% charcoal ash produced the highest average compressive strength of 23.68 MPa. Abstrak Beton merupakan material paling banyak digunakan diseluruh dunia dan terus dilakukan inovasi untuk menghasilkan pembangunan yang efisien. Abu arang tempurung dan abu sekam padi merupakan hasil sampingan industri yang berpotensi sebagai pengganti pasir untuk campuran beton, khususnya di Indragiri Hilir. Penelitian dengan judul “Pengaruh Campuran Abu Sekam Padi dan Abu Arang Tempurung Sebagai Pengganti Sebagian Agregat Halus Terhadap Kuat Tekan Beton” ini bertujuan membuktikan adanya pengaruh campuran abu arang tempurung dan abu sekam untuk mengganti sebagian pasir hingga menghasilkan kuat tekan maksimum. Beton adalah campuran antara semen portland, agregat halus, agregat kasar, dan air. Penelitian ini menggunakan 5 variasi campuran terhadap berat pasir, BSA 0 tanpa campuran pengganti, BSA 1 dengan campuran 5 % abu sekam dan 10% arang tempurung, BSA 2 dengan campuran 5% abu sekam dan 15% abu arang, BSA 3 dengan campuran 5% abu sekam dan 18% arang, BSA 4 dengan campuran 10% sekam dan 10% arang, dan BSA 5 dengan campuran 13% abu sekam dan 10% abu arang. Metode SNI digunakan untuk campuran Job Mix Formula (JMF)  pada penelitian ini. Hasil rata-rata kuat tekan beton pada umur 28 hari untuk JMF sebesar 21,05 MPa, BSA 1 sebesar 23,68 MPa, BSA 2 sebesar 22,23 MPa, BSA 3 sebesar 14,39 MPa, BSA 4 sebesar 13,34 MPa, dan BSA 5 Sebesar 20,14 MPa. Ditarik kesimpulan dari hasil penelitian BSA 1 dengan campuran 5% abu sekam dan 15% abu arang menghasilkan rata-rata kuat tekan tertinggi yaitu sebesar 23,68 MPa.  


Aggregates used in concrete are fast depleting natural resource and the quarrying of which is causing environmental issues. Hence, the use of aggregate from alternate sources such as from waste discarded glass, from foundry sand discarded after metal casting process and sea shells is investigated. Compressive strength of concrete with glass powder, foundry sand and sea shell is studied individually. Concrete is cast with glass powder and foundry sand as 5%, 10%, 15% and 20% replacement of fine aggregate and with sea shell as 5%, 10%, 15% and 20% replacement of coarse aggregate individually. It is observed that compressive strength of concrete decreases with glass powder, foundry sand, and sea shell. Fine aggregate replaced by 10% glass powder, 10%, foundry sand and coarse aggregate replaced by 10% sea shell have the least decrease in strength when compared to control concrete mix.


2021 ◽  
Vol 11 (4) ◽  
pp. 1952
Author(s):  
Euibae Lee ◽  
Jeongwon Ko ◽  
Jaekang Yoo ◽  
Sangjun Park ◽  
Jeongsoo Nam

In this study, the compressive strengths of concrete were investigated based on water content and aggregate volume fractions, comprising dune sand (DS), crushed sand (CS), and coarse aggregate (CA), for different ages. Experimental data were used to analyze the effects of the volume fraction changes of aggregates on the compressive strength. The compressive strength of concrete increases until the volumetric DS to fine aggregate (FA) ratio (DS/FA ratio) reaches 20%, after which it decreases. The relationship between changes in compressive strength and aggregate volume fractions was analyzed considering the effect factor of each aggregate on the compressive strength and at 2 conditions: (1) 0 < DS < CS < CA and (2) 0 < CA < CS < DS. For condition (1), when the effect factor of CA = 1, those of DS and CS were within 0.04–0.83 and 0.72–0.92, respectively, for all mixtures. For condition (2), when the effect factor of DS = 1, those of CS and CA were within 0.68–0.80 and 0.02–0.79, respectively.


2021 ◽  
Vol 2 (1) ◽  
pp. 46-54
Author(s):  
Neti Rahmawati ◽  
Irwan Lakawa ◽  
Sulaiman Sulaiman

Concrete is one of the most widely used building materials today interms of physical construction. Concrete is made from a mixture offine, coarse aggregate, cement, and water with a certain ratio, aswell as materials that are usually added to the concrete mixtureduring or during mixing, to changing the properties of concrete tomake it more suitable in certain jobs and more economical, can alsobe added with certain other mixed materials as needed if deemednecessary. Seashells can be used to mix concrete. This study aims todetermine whether the addition of shells aggregate shells in aconcrete mixture can affect the mechanical properties of concrete.The specimens used are in the form of cubes with a size of 15cm x 15cm x 15 cm, consisting of additional concrete coarse and fineaggregate with shell substitution percentage of 0%, 15%, 20% with atotal sample of 45, with the planned concrete quality of K225. Theuse of sea shells in increasing the compressive strength of concrete isbetter used as fine aggregate than coarse aggregate. The use of seashells as a substitute for fine aggregates achieves maximum resultsat 20% composition.


This paper presents an application of fuzzy logic to forecast the compressive strength of concrete. The fuzzy model examines 7 different input parameters that comprises: Cement, Coarse aggregate(CA), Super plasticizer(SP), Fine Aggregate(FA), Slag, Fly ash, Water(W), and 28 days compressive strength is taken as the output parameter. By using Gaussian membership function, the fuzzy logic technique is used for developing models. For assessing the results of FL model with experimental results, root mean square error, mean absolute error and correlation coefficient are used. The results showed that FL can be a better modeling tool and an another technique for predicting the concrete’s compressive strength.


2018 ◽  
Vol 5 (1) ◽  
pp. 28
Author(s):  
Adiwijaya Ali ◽  
Irka Tangke Datu

The goal of this research is to investigate the influence of seawater as mixing water and curing water on characteristics of cement paste and mortar. Research was conducted with making mixtures of cement paste and mortar using two kind of cement, Portland Composite Cement (PCC) and Pozzolana Portland Cement (PPC) with seawater as mixing water. Characteristics of fine aggregate and characteristics of cement paste with seawater mixing were investigated. Furthermore, 144 cube mortar specimens in size of 5 cm x 5 cm x 5 cm in four series mortar mixtures were casted according with SNI 03-6825-2002. At 24 hours after specimens were casted, cube mortar specimens were cured in tap water curing (TC), seawater curing (SC) and air curing (AC). After achievement at certain curing day of 3, 7, 14 and 28 days, cube mortar samples were tested in compressive strength. Results concluded that seawater mixing improves compressive strength of mortar up to 28 days in all curing conditions, TC, SC and AC. Moreover, strength of mortar is not affected by type of curing water, tap water or seawater.


2020 ◽  
Vol 27 (3) ◽  
pp. 45-60
Author(s):  
Muataz Nayel ◽  
Ammar Khazaal ◽  
Waleed Alabdraba

Recently, the constructions industry begins to make concrete more sustainable, side by side, with making its high performance. This paper aims to investigate the effect of (Metakaolin and Micro Silica) when they replace cement by (8, 12 and 16) % and (6, 9 and 12) % respectively, recycled steel slag when replaces fine aggregate by (10, 20 and 30) %, and recycled mosaic tiles when replaces coarse aggregate by (33.33, 66.67 and 100) % each one another on the slump, density, absorption and compressive strength of concrete. The experimental results showed that the maximum reduction ratio of cement reach (17%) (8% of metakaolin and 9% Micro Silica) while the optimum percentage of mosaic tiles and steel slag is (100%) and (20%) respectively. The optimum percentages obtained are combining to produce three basic green mixes: 1) 17% (8% of Metakaolin and 9% of Micro Silica) only, (2) A mix containing 17% of (Metakaolin and of Micro Silica) plus 100% of recycled mosaic, (3) 17% of (Metakaolin and Micro Silica), 100% of recycled mosaic and 20% of slag. Compressive strength at (7, 28, and 60) days, modulus of rupture at (28) days, absorption, fresh and hardened density are investigated. The best improvement in compressive strength compared with reference concrete was recorded (20.06, 10.855 and 9.983) % at (7, 28 and 60) days respectively for the mix containing (17% of cementitious materials plus 100% of recycled mosaic) while the ultimate flexure strength (24) % appeared in green mix containing (17% of cementitious materials, 100% of recycled mosaic and 20% of slag). Generally, an inverse relationship between density and absorption in all trail mixes which are conducted


2019 ◽  
Vol 136 ◽  
pp. 03009
Author(s):  
Yue Tian ◽  
Wanlai Zhang ◽  
Yihang Zhang

Based on the construction characteristics in the Northeast China Region under low temperature conditions, this article studies the influences of admixtures without antifreezing agent of different types and amounts on the low-temperature concrete and characteristics of pore structure. The results show that the amount of the admixtures is stable, the compressive strength of concrete under the curing condition of low temperature naturally varying is higher than the strength under the curing condition of constant low temperature while the porosity of the concrete under the curing condition of low temperature naturally varying is lower than the porosity under the curing condition of constant low temperature; The most appropriate curing method for the concrete used in winter construction is the curing method of low temperature naturally varying.


2013 ◽  
Vol 421 ◽  
pp. 390-394 ◽  
Author(s):  
Abdullah Mohd Mustafa Al Bakri ◽  
M.N. Norazian ◽  
M. Mohamed ◽  
H. Kamarudin ◽  
C.M. Ruzaidi ◽  
...  

This research focuses on a study of the strength of concrete with ceramic waste as coarse aggregate and quarry dust as fine aggregate. The sources of ceramic waste and quarry dust are obtained from the industrial in Malaysia. Presently, in ceramics industries the production goes as waste, which is not under going the recycle process yet. In this study an attempt has been made to find the suitability of the ceramic industrial wastes and quarry dust as a possible replacement for conventional crushed stone coarse and fine aggregate. Experiment were carried out to determine the strength of concrete with ceramic waste coarse aggregate and quarry dust fine aggregate to compare them with the conventional concrete made (with crushed stone coarse aggregate). From the results show that compressive strength of concrete with quarry dust as aggregates is the highest with 30.82 MPa with density 2251.85 kg/m3. This show, ceramic waste and quarry dust can be alternative aggregate for comparable properties.


Sign in / Sign up

Export Citation Format

Share Document