scholarly journals An Efficient and Simple Method for Modelling Solar Cells

2019 ◽  
Vol 64 (1) ◽  
pp. 40-46
Author(s):  
Ali Kareem Abdulrazzaq ◽  
György Bognár ◽  
Balázs Plesz
Keyword(s):  
Solar Cell ◽  
Environmental Conditions ◽  
Fixed Time ◽  
Linear Interpolation ◽  
Time Interval ◽  
Two Dimensional ◽  
Pv System ◽  
Simple Method ◽  
Wide Range ◽  
Crystalline Solar Cell

Accurate and reliable PV device modelling is a fundamental tool to optimize system performance. The regular operation of the PV system in an outdoor condition implies the need for a model that relate the environmental effects. This paper presents a new, simple, and efficient method for constructing the I-V characteristics for a PV cell incorporating the environmental conditions. The proposed model is based on the idea of dividing the voltage axis of the solar cell I-V characteristics using a fixed time interval. For each voltage interval point, a two-dimensional current matrix is calculated, corresponding different irradiance conditions and temperatures. Polynomial surface fitting is used to build sub-models for each voltage interval. The current two-dimensional matrix, for each point, is calculated by two different methods. The first method is based on linear interpolation of the measured I-V curves. The second method uses pre-extracted five parameters for the well known single diode model at a wide range of environmental conditions. The developed modelling technique provides accurate results compared with the measured data for a mono-crystalline solar cell.

scholarly journals PV Systems Installed in Marine Vessels: Technologies and Specifications

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Ioannis Kobougias ◽  
Emmanuel Tatakis ◽  
John Prousalidis
Keyword(s):  
Solar Cell ◽  
Environmental Conditions ◽  
Cell Types ◽  
Pv System ◽  
Electrical Grid ◽  
Pv Systems ◽  
Technical Specifications ◽  
Marine Vessels ◽  
Marine Environmental

Considerations are held about the specificationin whichthe PV plants have to fulfill so that they can be installed on marine vessels. Initially, a brief description of the typical electrical grid of ships is presented, distinguishing the main parts, reporting the typical electrical magnitudes, and choosing the most preferable installation areas. The technical specifications,in whichthe PV plants have to be compatible with, are fully described. They are determined by the special marine environmental conditions, taking into consideration parameters like wind, humidity, shading, corrosion, and limited installation area. The work is carried out with the presentation of the most popular trends in the field of solar cell types and PV system technologies and their ability to keep up with the aforementioned specifications.

An Experimental and Theoretical Study on Cavitating Cascades and Their Application to Cavitating Propellers

1985 ◽  
Vol 29 (01) ◽  
pp. 23-38
Author(s):  
Okitsugu Furuya ◽  
Shin Maekawa
Keyword(s):  
Experimental Data ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Two Dimensional ◽  
Simple Method ◽  
Cascade Theory ◽  
Wide Range ◽  
Line Theory ◽  
Lifting Line ◽  
Lifting Line Theory

In order to develop an analytical tool for predicting the off-design performance of supercavitating propellers over a wide range of operating conditions, a lifting-line theory was combined with a two-dimensional supercavitating cascade theory. The results of this simple method provided fairly accurate predictions for the performance at fully developed cavitating conditions. It was indicative that the fully developed supercavitating (s/c) propellers had strong cascade effects on their performance, and also that the three-dimensional propeller geometry corrections could properly be made by the lifting-line theory. However, the predicted performance with this propeller theory showed a significant deviation from experimental data in the range of J's larger than Jdesign, where partially cavitating conditions are expected to occur. Effort was then made on improving the prediction capability of the above propeller theory at partially cavitating (p/c) conditions. A new nonlinear partially cavitating cascade theory was then developed to provide a proper 2-D loading basis under such conditions. Two-dimensional cascade experiments were then conducted to prove the accuracy of the p/c and s/c cascade theories. The measured forces and flow observations obtained in these experiments shed a new light on the relationship between the forces and cavitation numbers at small angles of incidence. Corrected lift and drag forces were then used in the propeller program. The calculated results for KT and KQ with the new force data successfully correlated with the experimental data, now covering a large J-range where the partially cavitating conditions exist.

Aromatic Volatile Composition of Celery and Celeriac Cultivars

HortScience ◽  
1990 ◽  
Vol 25 (5) ◽  
pp. 556-559 ◽  
Author(s):  
Fredy Van Wassenhove ◽  
Patrick Dirinck ◽  
Georges Vulsteke ◽  
Niceas Schamp
Keyword(s):  
Volatile Compounds ◽  
Chromatographic Method ◽  
Apium Graveolens ◽  
Volatile Components ◽  
Two Dimensional ◽  
Qualitative Composition ◽  
Volatile Composition ◽  
Wide Range ◽  
Gas Chromatographic Method ◽  
Identification And Quantification

A two-dimensional capillary gas chromatographic method was developed to separate and quantify aromatic volatiles of celery in one analysis. The isolation, identification, and quantification of the volatile compounds of four cultivars of blanching celery (Apium graveolens L. var. dulce) and six cultivars of celeriac (Apium graveolens L. var. rapaceum) are described. The qualitative composition of Likens-Nickerson extracts of both cultivars is similar. The concentration of terpenes and phthalides, the key volatile components, found in various cultivars of both celery and celeriac varied over a wide range.

Utilization of remote sensing for estimation of scale of cutting and growing of forest zones

2017 ◽  
Vol 920 (2) ◽  
pp. 57-60
Author(s):  
F.E. Guliyeva
Keyword(s):  
Remote Sensing ◽  
Fixed Time ◽  
Time Interval ◽  
Time Points ◽  
Average Value ◽  
Time Period ◽  
Remote Estimation ◽  
The Given ◽  
Forest Cutting

The study of results of relevant works on remote sensing of forests has shown that the known methods of remote estimation of forest cuts and growth don’t allow to calculate the objective average value of forests cut volume during the fixed time period. The existing mathematical estimates are not monotonous and make it possible to estimate primitively the scale of cutting by computing the ratio of data in two fixed time points. In the article the extreme properties of the considered estimates for deforestation and reforestation models are researched. The extreme features of integrated averaged values of given estimates upon limitations applied on variables, characterizing the deforestation and reforestation processes are studied. The integrated parameter, making it possible to calculate the averaged value of estimates of forest cutting, computed for all fixed time period with a fixed step is suggested. It is shown mathematically that the given estimate has a monotonous feature in regard of value of given time interval and make it possible to evaluate objectively the scales of forest cutting.

scholarly journals Model for Predicting the Operating Temperature of Stratospheric Airship Solar Cells with a Support Vector Machine

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1228
Author(s):  
Xuwei Wang ◽  
Zhaojie Li ◽  
Yanlei Zhang
Keyword(s):  
Support Vector Machine ◽  
Solar Cell ◽  
Energy Balance ◽  
Output Power ◽  
Operating Temperature ◽  
Support Vector ◽  
Power Calculation ◽  
Pv System ◽  
Stratospheric Airship ◽  
Cell Modules

The stratospheric airship is a kind of aircraft that completely relies on the cycle of photovoltaic energy systems to achieve long duration flight. The accurate estimation of the operating temperature of solar cell modules on stratospheric airship is extremely important for the design of photovoltaics system (PV system), the output power calculation of PV system, and the calculation of energy balance. However, the related study has been rarely reported. A support vector machine prediction method based on particle swarm optimization algorithm (PSO-SVM) was established to predict the operating temperature of solar cell modules on stratospheric airship. The PSO algorithm was used to dynamically optimize the SVM’s parameters between the operating temperature of the solar cell modules and the measured data such as atmospheric pressure, solar radiation intensity, flight speed, and ambient temperature. The operating temperature data of the two sets of solar cell modules measured in the flight test were used to verify the accuracy of the temperature prediction model, and the prediction results were compared with a back propagation neural network (BPNN) method and the simulation results calculated by COMSOL Multiphysics of COMSOL, Inc., Columbus, MA, USA. The results shown that the PSO-SVM model realized the accurate prediction of the operating temperature of solar cell modules on stratospheric airship, which can guide the design of PV system, the output power calculation of PV system, and the calculation of energy balance.

scholarly journals Prediction of Wide Range Two-Dimensional Refractivity Using an IDW Interpolation Method from High-Altitude Refractivity Data of Multiple Meteorological Observatories

2021 ◽  
Vol 11 (4) ◽  
pp. 1431
Author(s):  
Sungsik Wang ◽  
Tae Heung Lim ◽  
Kyoungsoo Oh ◽  
Chulhun Seo ◽  
Hosung Choo
Keyword(s):  
High Altitude ◽  
Korean Peninsula ◽  
Interpolation Method ◽  
Atmospheric Condition ◽  
Propagation Path ◽  
Two Dimensional ◽  
Data Set ◽  
Wide Range ◽  
Atmospheric Data ◽  
Terrain Surface

This article proposes a method for the prediction of wide range two-dimensional refractivity for synthetic aperture radar (SAR) applications, using an inverse distance weighted (IDW) interpolation of high-altitude radio refractivity data from multiple meteorological observatories. The radio refractivity is extracted from an atmospheric data set of twenty meteorological observatories around the Korean Peninsula along a given altitude. Then, from the sparse refractive data, the two-dimensional regional radio refractivity of the entire Korean Peninsula is derived using the IDW interpolation, in consideration of the curvature of the Earth. The refractivities of the four seasons in 2019 are derived at the locations of seven meteorological observatories within the Korean Peninsula, using the refractivity data from the other nineteen observatories. The atmospheric refractivities on 15 February 2019 are then evaluated across the entire Korean Peninsula, using the atmospheric data collected from the twenty meteorological observatories. We found that the proposed IDW interpolation has the lowest average, the lowest average root-mean-square error (RMSE) of ∇M (gradient of M), and more continuous results than other methods. To compare the resulting IDW refractivity interpolation for airborne SAR applications, all the propagation path losses across Pohang and Heuksando are obtained using the standard atmospheric condition of ∇M = 118 and the observation-based interpolated atmospheric conditions on 15 February 2019. On the terrain surface ranging from 90 km to 190 km, the average path losses in the standard and derived conditions are 179.7 dB and 182.1 dB, respectively. Finally, based on the air-to-ground scenario in the SAR application, two-dimensional illuminated field intensities on the terrain surface are illustrated.

scholarly journals Is contact angle a cause or an effect? – A cautionary tale

2020 ◽  
Vol 146 ◽  
pp. 03004
Author(s):  
Douglas Ruth
Keyword(s):  
Contact Angle ◽  
Solid Surface ◽  
Contact Angles ◽  
Two Dimensions ◽  
Experimental Results ◽  
Flow In Porous Media ◽  
Two Dimensional ◽  
Wide Range ◽  
Fluid Drop ◽  
Surrounding Fluid

The most influential parameter on the behavior of two-component flow in porous media is “wettability”. When wettability is being characterized, the most frequently used parameter is the “contact angle”. When a fluid-drop is placed on a solid surface, in the presence of a second, surrounding fluid, the fluid-fluid surface contacts the solid-surface at an angle that is typically measured through the fluid-drop. If this angle is less than 90°, the fluid in the drop is said to “wet” the surface. If this angle is greater than 90°, the surrounding fluid is said to “wet” the surface. This definition is universally accepted and appears to be scientifically justifiable, at least for a static situation where the solid surface is horizontal. Recently, this concept has been extended to characterize wettability in non-static situations using high-resolution, two-dimensional digital images of multi-component systems. Using simple thought experiments and published experimental results, many of them decades old, it will be demonstrated that contact angles are not primary parameters – their values depend on many other parameters. Using these arguments, it will be demonstrated that contact angles are not the cause of wettability behavior but the effect of wettability behavior and other parameters. The result of this is that the contact angle cannot be used as a primary indicator of wettability except in very restricted situations. Furthermore, it will be demonstrated that even for the simple case of a capillary interface in a vertical tube, attempting to use simply a two-dimensional image to determine the contact angle can result in a wide range of measured values. This observation is consistent with some published experimental results. It follows that contact angles measured in two-dimensions cannot be trusted to provide accurate values and these values should not be used to characterize the wettability of the system.

scholarly journals Two-Dimensional Visualization of the Three-Dimensional Planned Sacroiliac Screw Corridor with the Slice Fusion Method

2021 ◽  
Vol 10 (2) ◽  
pp. 184
Author(s):  
Maximilian Kerschbaum ◽  
Siegmund Lang ◽  
Florian Baumann ◽  
Volker Alt ◽  
Michael Worlicek
Keyword(s):  
Pelvic Ring ◽  
Three Dimensional ◽  
Fusion Method ◽  
Two Dimensional ◽  
Posterior Pelvic Ring ◽  
Simple Method ◽  
Sacroiliac Screw ◽  
Screw Insertion ◽  
Multiplanar Reconstructions ◽  
Screw Position

Insertion of sacro-iliac (SI) screws for stabilization of the posterior pelvic ring without intraoperative navigation or three-dimensional imaging can be challenging. The aim of this study was to develop a simple method to visualize the ideal SI screw corridor, on lateral two-dimensional images, corresponding to the lateral fluoroscopic view, used intraoperatively while screw insertion, to prevent neurovascular injury. We used multiplanar reconstructions of pre- and postoperative computed tomography scans (CT) to determine the position of the SI corridor. Then, we processed the dataset into a lateral two-dimensional slice fusion image (SFI) matching head and tip of the screw. Comparison of the preoperative SFI planning and the screw position in the postoperative SFI showed reproducible results. In conclusion, the slice fusion method is a simple technique for translation of three-dimensional planned SI screw positioning into a two-dimensional strict lateral fluoroscopic-like view.

scholarly journals Robust anomalous metallic states and vestiges of self-duality in two-dimensional granular In-InOx composites

2021 ◽  
Vol 6 (1) ◽  
Author(s):  
Xinyang Zhang ◽  
Bar Hen ◽  
Alexander Palevski ◽  
Aharon Kapitulnik
Keyword(s):  
Magnetic Field ◽  
Metallic Phase ◽  
Broadband Noise ◽  
Two Dimensional ◽  
Conventional Theory ◽  
Logarithmic Divergence ◽  
Self Duality ◽  
Low Field ◽  
Wide Range ◽  
Low Temperature Resistance

AbstractMany experiments investigating magnetic-field tuned superconductor-insulator transition (H-SIT) often exhibit low-temperature resistance saturation, which is interpreted as an anomalous metallic phase emerging from a ‘failed superconductor’, thus challenging conventional theory. Here we study a random granular array of indium islands grown on a gateable layer of indium-oxide. By tuning the intergrain couplings, we reveal a wide range of magnetic fields where resistance saturation is observed, under conditions of careful electromagnetic filtering and within a wide range of linear response. Exposure to external broadband noise or microwave radiation is shown to strengthen the tendency of superconductivity, where at low field a global superconducting phase is restored. Increasing magnetic field unveils an ‘avoided H-SIT’ that exhibits granularity-induced logarithmic divergence of the resistance/conductance above/below that transition, pointing to possible vestiges of the original emergent duality observed in a true H-SIT. We conclude that anomalous metallic phase is intimately associated with inherent inhomogeneities, exhibiting robust behavior at attainable temperatures for strongly granular two-dimensional systems.

Sign in / Sign up

Export Citation Format

Share Document