scholarly journals Hydroxy Gas (HHO) Supplement of Ethanol Fuel Mixture In A Single-Cylinder Spark-Ignition Matic-Engine

2020 ◽  
Vol 5 (2) ◽  
pp. 114
Author(s):  
Gatot Setyono
Keyword(s):  
Thermal Efficiency ◽  
Alternative Energy ◽  
Fuel Injection ◽  
Control Unit ◽  
Fuel Mixture ◽  
Single Cylinder ◽  
Spark Plug ◽  
Octane Rating ◽  
Pressure Cycle ◽  
Efficient Alternative

<p class="TTPAbstract">Hydroxy Gas (HHO) has been identified as an efficient alternative energy source. HHO is considered an alternative fuel. It can be applied alone or mixed with other kind of fuels in different ratios. In this analysis, the composition of HHO-ethanol was mixed in different variations. Ethanol-HHO was chosen because of its high-octane rating yet low exhaust emissions, and ease of obtaining from engine products. It has been applied on fuel prepared by mixing it with gasoline in various ratios (E30-HHO, E40-HHO, and E50-HHO). The ethanol-HHO mixture has been used in a single-cylinder 4-stroke spark machine for performance, by varying speed of engine from 4000 to 9000 RPM and by applying a platinum spark plug electrode type. In experiments, engine power, average effective pressure (MEP), specific fuel consumption (SFC), and thermal efficiency have been analyzed. The analysis of combustion is accomplished by taking a pressure cycle in the chamber, monitoring the automatic control of engine control unit (ECU) and ensuring utilization in the same parameters of the various fuels tested, in addition to the fuel injection time, which increases with increasing ethanol percentage. Optimal power, MEP and thermal efficiency values are obtained with ethanol-gasoline (E50-HHO) mixture which is operated at 7200 rpm, an increase of about 5% compared to gasoline. Significant reduction in SFC was observed using HHO-ethanol mixture, reduced by about 6% compared to gasoline.</p>

scholarly journals Performances of a Research CFR Octane Rating Unit Engine and Dacia Single Cylinder SI Engine Ignited by a LASER System

2019 ◽  
Vol 112 ◽  
pp. 01009
Author(s):  
Bogdan George Done ◽  
Ion Copae
Keyword(s):  
New Technologies ◽  
Combustion Process ◽  
Pollutant Emissions ◽  
Laser Medium ◽  
Si Engine ◽  
Engine Operation ◽  
Single Cylinder ◽  
Spark Plug ◽  
Octane Rating ◽  
Laser Spark

At this time, the severe legislation regarding the level limits of the waste and exhaust gases released by thermal engines and also the necessity of engines efficiency improvement boost the engine research domain to bring in front the use of new technologies that can be used to control the in-cylinder combustion process. Now, the new technologies is represented by LASER spark plug systems which can be successfully used at petrol engines. LASER spark plug technology can have many advantages for engine operation control, an ignition system that could provide improved combustion is the one using plasma generation and a Q-switched LASER that results in pulses with high MW power. The LASER spark plug device used in the current research was a LASER medium Nd:YAG/Cr4+:YAG ceramic structure made up of a 8.0-mm long, 1.0-at.% Nd:YAG ceramic, optically-bonded to a Cr4+:YAG c. It was developed and constructed similar to classical spark plug and could be assembled on a CFR Octane Rating Unit Engine as well as on a Dacia Single Cylinder SI Engine which led to several results among which: influences on in-cylinder pressure, combustion and pollutant emissions.

scholarly journals CFR Octane Rating Unit Engine and Dacia Single Cylinder SI Engine with Classical Spark Plug and Laser Ignition: Comparative Findings

2019 ◽  
Vol 2 (2) ◽  
pp. 39-42
Author(s):  
Bogdan George Done ◽  
◽  
Laszlo Barothi ◽  
Ion Copae ◽  
◽  
...  
Keyword(s):  
Laser Ignition ◽  
Si Engine ◽  
Single Cylinder ◽  
Spark Plug ◽  
Octane Rating

scholarly journals Effect of algae fuel addition on fuel consumption and thermal efficiency of single cylinder diesel engine

2021 ◽  
Vol 1068 (1) ◽  
pp. 012016
Author(s):  
Hazim Sharudin ◽  
N.A. Rahim ◽  
N.I. Ismail ◽  
Sharzali Che Mat ◽  
Nik Rosli Abdullah ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Single Cylinder

Dual-Location Fuel Injection Effects on Emissions and NO*/OH* Chemiluminescence in a High Intensity Combustor

2016 ◽  
Vol 138 (4) ◽  
Author(s):  
Ahmed O. Said ◽  
Ahmed E. E. Khalil ◽  
Ashwani K. Gupta
Keyword(s):  
Fuel Injection ◽  
Single Injection ◽  
Mixing Time ◽  
Fuel Mixture ◽  
Combustion Noise ◽  
Fuel Distribution ◽  
Mixture Preparation ◽  
Pollutants Emission ◽  
Fuel Mixing ◽  
Colorless Distributed Combustion

Colorless distributed combustion (CDC) has shown to provide ultra-low emissions of NO, CO, unburned hydrocarbons, and soot, with stable combustion without using any flame stabilizer. The benefits of CDC also include uniform thermal field in the entire combustion space and low combustion noise. One of the critical aspects in distributed combustion is fuel mixture preparation prior to mixture ignition. In an effort to improve fuel mixing and distribution, several schemes have been explored that includes premixed, nonpremixed, and partially premixed. In this paper, the effect of dual-location fuel injection is examined as opposed to single fuel injection into the combustor. Fuel distribution between different injection points was varied with the focus on reaction distribution and pollutants emission. The investigations were performed at different equivalence ratios (0.6–0.8), and the fuel distribution in each case was varied while maintaining constant overall thermal load. The results obtained with multi-injection of fuel using a model combustor showed lower emissions as compared to single injection of fuel using methane as the fuel under favorable fuel distribution condition. The NO emission from double injection as compared to single injection showed a reduction of 28%, 24%, and 13% at equivalence ratio of 0.6, 0.7, and 0.8, respectively. This is attributed to enhanced mixture preparation prior to the mixture ignition. OH* chemiluminescence intensity distribution within the combustor showed that under favorable fuel injection condition, the reaction zone shifted downstream, allowing for longer fuel mixing time prior to ignition. This longer mixing time resulted in better mixture preparation and lower emissions. The OH* chemiluminescence signals also revealed enhanced OH* distribution with fuel introduced through two injectors.

Study of High Load Operation Limit Expansion for Gasoline Compression Ignition Engines

2006 ◽  
Vol 128 (2) ◽  
pp. 377-387 ◽  
Author(s):  
Koudai Yoshizawa ◽  
Atsushi Teraji ◽  
Hiroshi Miyakubo ◽  
Koichi Yamaguchi ◽  
Tomonori Urushihara
Keyword(s):  
Fuel Injection ◽  
Control Method ◽  
Combustion Process ◽  
High Load ◽  
Compression Ignition ◽  
Ignition Timing ◽  
Timing Control ◽  
Load Range ◽  
Compression Ignition Engines ◽  
Spark Plug

In this research, combustion characteristics of gasoline compression ignition engines have been analyzed numerically and experimentally with the aim of expanding the high load operation limit. The mechanism limiting high load operation under homogeneous charge compression ignition (HCCI) combustion was clarified. It was confirmed that retarding the combustion timing from top dead center (TDC) is an effective way to prevent knocking. However, with retarded combustion, combustion timing is substantially influenced by cycle-to-cycle variation of in-cylinder conditions. Therefore, an ignition timing control method is required to achieve stable retarded combustion. Using numerical analysis, it was found that ignition timing control could be achieved by creating a fuel-rich zone at the center of the cylinder. The fuel-rich zone works as an ignition source to ignite the surrounding fuel-lean zone. In this way, combustion consists of two separate auto-ignitions and is thus called two-step combustion. In the simulation, the high load operation limit was expanded using two-step combustion. An engine system identical to a direct-injection gasoline (DIG) engine was then used to validate two-step combustion experimentally. An air-fuel distribution was created by splitting fuel injection into first and second injections. The spark plug was used to ignite the first combustion. This combustion process might better be called spark-ignited compression ignition combustion (SI-CI combustion). Using the spark plug, stable two-step combustion was achieved, thereby validating a means of expanding the operation limit of gasoline compression ignition engines toward a higher load range.

scholarly journals Impact of injection strategies on combustion characteristics, efficiency and emissions of gasoline compression ignition operation in a heavy-duty multi-cylinder engine

2018 ◽  
Vol 21 (8) ◽  
pp. 1426-1440 ◽  
Author(s):  
Buyu Wang ◽  
Michael Pamminger ◽  
Ryan Vojtech ◽  
Thomas Wallner
Keyword(s):  
High Temperature ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Pressure Rise ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Gas Recirculation ◽  
Direct Fuel Injection

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low-temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high-temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Furthermore, for high-temperature gasoline compression ignition, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high-temperature gasoline compression ignition combustion with port and direct injection. Engine testing was conducted at an engine speed of 1038 r/min and brake mean effective pressure of 1.4 MPa for three injection strategies, late pilot injection, early pilot injection, and port/direct fuel injection. The impact on engine performance and emissions with respect to varying the combustion phasing were quantified within this study. At the same combustion phasing, early pilot injection and port/direct fuel injection had an earlier start of combustion and higher maximum pressure rise rates than late pilot injection attributable to more premixed fuel from pilot or port injection; however, brake thermal efficiencies were higher with late pilot injection due to reduced heat transfer. Early pilot injection also exhibited the highest cylinder-to-cylinder variations due to differences in injector behavior as well as the spray/wall interactions affecting mixing and evaporation process. Overall, peak brake thermal efficiency of 46.1% and 46% for late pilot injection and port/direct fuel injection was achieved comparable to diesel baseline (45.9%), while early pilot injection showed the lowest brake thermal efficiency (45.3%).

RCCI of Synthetic Kerosene With PFI of N-Butanol-Combustion and Emissions Characteristics

2015 ◽  
Author(s):  
Valentin Soloiu ◽  
Martin Muiños ◽  
Tyler Naes ◽  
Spencer Harp ◽  
Marcis Jansons
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Cetane Number ◽  
Engine Performance ◽  
Reactivity Controlled Compression Ignition ◽  
Ultra Low Sulfur Diesel ◽  
Indicated Mean Effective Pressure ◽  
Soot Emissions ◽  
Low Sulfur

In this study, the combustion and emissions characteristics of Reactivity Controlled Compression Ignition (RCCI) obtained by direct injection (DI) of S8 and port fuel injection (PFI) of n-butanol were compared with RCCI of ultra-low sulfur diesel #2 (ULSD#2) and PFI of n-butanol at 6 bar indicated mean effective pressure (IMEP) and 1500 rpm. S8 is a synthetic paraffinic kerosene (C6–C18) developed by Syntroleum and is derived from natural gas. S8 is a Fischer-Tropsch fuel that contains a low aromatic percentage (0.5 vol. %) and has a cetane number of 63 versus 47 of ULSD#2. Baselines of DI conventional diesel combustion (CDC), with 100% ULSD#2 and also DI of S8 were conducted. For both RCCI cases, the mass ratio of DI to PFI was set at 1:1. The ignition delay for the ULSD#2 baseline was found to be 10.9 CAD (1.21 ms) and for S8 was shorter at 10.1 CAD (1.12 ms). In RCCI, the premixed charge combustion has been split into two regions of high temperature heat release, an early one BTDC from ignition of ULSD#2 or S8, and a second stage, ATDC from n-butanol combustion. RCCI with n-butanol increased the NOx because the n-butanol contains 21% oxygen, while S8 alone produced 30% less NOx emissions when compared to the ULSD#2 baseline. The RCCI reduced soot by 80–90% (more efficient for S8). However, S8 alone showed a considerable increase in soot emissions compared with ULSD#2. The indicated thermal efficiency was the highest for the ULSD#2 and S8 baseline at 44%. The RCCI strategies showed a decrease in indicated thermal efficiency at 40% ULSD#2-RCCI and 42% and for S8-RCCI, respectively. S8 as a single fuel proved to be a very capable alternative to ULSD#2 in terms of combustion performance nevertheless, exhibited higher soot emissions that have been mitigated with the RCCI strategy without penalty in engine performance.

scholarly journals Use of the mathematical model of the ignition system to analyze the spark discharge, including the destruction of spark plug electrodes

Open Physics ◽  
2018 ◽  
Vol 16 (1) ◽  
pp. 57-62 ◽  
Author(s):  
Sebastian Różowicz
Keyword(s):  
Mathematical Model ◽  
Experimental Studies ◽  
Fuel Mixture ◽  
Spark Discharge ◽  
Fuel Additives ◽  
Ignition System ◽  
Spark Plug ◽  
The Mathematical Model

Abstract The paper presents the results of analytical and experimental studies concerning the influence of different kinds of fuel additives on the quality of the spark discharge for different configurations of the ignition system. The wear of the spark plug electrode and the value of spark discharge were determined for various impurities and configurations of the air-fuel mixture.

Sign in / Sign up

Export Citation Format

Share Document