scholarly journals Drag coefficient calculation of modified Myring-Savonius wind turbine with numerical simulations

2020 ◽  
Vol 10 (2) ◽  
pp. 73-84
Author(s):  
Mahmoud Saleh ◽  
Endre Kovács
Keyword(s):  
Drag Coefficient ◽  
Wind Turbine ◽  
Primary Objective ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Energy Potential ◽  
Cross Sectional ◽  
Ansys Fluent ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine

Nowadays the importance of renewable energy is growing, and the utilization of the low wind energy potential is getting crucial. There are turbines with low and high tip speed ratio. Turbines with low tip speed ratio such as the Savonius wind turbine can generate adequate amount of torque at low wind velocities. These types of turbines are also called drag machines. The geometry of the blade can greatly influence the efficiency of the device. With Computational Fluid Dynamics (CFD) method, several optimizations can be done before the production. In our paper the Savonius wind turbine blade geometry was designed based on the so-called Myring equation. The primary objective of this paper was to investigate the drag coefficient of the force acting on the surface of the blade. Also, the Karman vortex was investigated and the space ratio of that vortex in our simulation was compared to a typical one. The power coefficient of a new Savonius turbine was investigated at different values of top speed ratio (TSR). For the sake of simplicity, a 2D cross-sectional area was investigated in the simulation with ANSYS Fluent 19.2.

scholarly journals Numerical Model Analysis of Myring–Savonius wind turbines

2019 ◽  
Vol 4 (1) ◽  
pp. 180-185
Author(s):  
M. Saleh ◽  
Ferenc Szodrai
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Primary Objective ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Energy Potential ◽  
Cross Sectional ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine ◽  
Cfd Method

Nowadays the importance of renewable energy is growing, and the utilization of the low wind energy potential is getting crucial. There are turbines with low and high tip speed ratio. Turbines with low tip speed ratio such as the Savonius wind turbine can generate adequate amount of torque at low wind velocities. These types of turbines are also called drag machines. The geometry of the blade can greatly influence the efficiency of the device. With Computational Fluid Dynamics (CFD) method, several optimizations can be done before the production. In our paper the Savonius wind turbine blade geometry was based on the so-called Myring equation. The primary objective of this paper was to increase the power coefficient by modelling the effect of the wind on the turbine blade. For the sake of simplicity, a 2D cross-sectional area was investigated in the simulation with ANSYS CFX 19.1.

scholarly journals Performance assessment and optimization of a helical Savonius wind turbine by modifying the Bach’s section

2021 ◽  
Vol 3 (8) ◽  
Author(s):  
M. Niyat Zadeh ◽  
M. Pourfallah ◽  
S. Safari Sabet ◽  
M. Gholinia ◽  
S. Mouloodi ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Performance Assessment ◽  
Turbulent Flows ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Basic Model ◽  
Turbine Performance ◽  
Primary Model ◽  
Savonius Wind Turbine

AbstractIn this paper, we attempted to measure the effect of Bach’s section, which presents a high-power coefficient in the standard Savonius model, on the performance of the helical Savonius wind turbine, by observing the parameters affecting turbine performance. Assessment methods based on the tip speed ratio, torque variation, flow field characterizations, and the power coefficient are performed. The present issue was stimulated using the turbulence model SST (k- ω) at 6, 8, and 10 m/s wind flow velocities via COMSOL software. Numerical simulation was validated employing previous articles. Outputs demonstrate that Bach-primary and Bach-developed wind turbine models have less flow separation at the spoke-end than the simple helical Savonius model, ultimately improving wind turbines’ total performance and reducing spoke-dynamic loads. Compared with the basic model, the Bach-developed model shows an 18.3% performance improvement in the maximum power coefficient. Bach’s primary model also offers a 12.4% increase in power production than the initial model’s best performance. Furthermore, the results indicate that changing the geometric parameters of the Bach model at high velocities (in turbulent flows) does not significantly affect improving performance.

scholarly journals Studi simulasi penggunaan airfoil naca 6412 sebagai sudu pada turbin angin crossflow melalui pemodelan CFD 2 dimensi

2018 ◽  
Vol 13 (1) ◽  
pp. 28
Author(s):  
Muhammad Ivan Fadhil Hendrawan ◽  
Dominicus Danardono ◽  
Syamsul Hadi
Keyword(s):  
Wind Turbine ◽  
Constant Velocity ◽  
Cross Flow ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Ansys Fluent ◽  
Tip Speed Ratio ◽  
Blade Number

AbstractThe simulation aimed to understand the effect of the angle of blade number and blade number of vertical axis wind turbine with cross flow runner to enhance the performance of wind turbine. The turbine had 20, 22, and 24 number of blades. Simulation was done in 2D analysis using ANSYS-Fluent. Tip speed ratio was varied in range of 0,1-0,5 with constant velocity inlet 2 m/s. The effect of blade numbers to torque and power coefficient were analyzed and compared. It had been found that the best power coefficient were 0,5 at tip speed ratio 0,3.

scholarly journals An innovative augmentation technique of savonius wind turbine performance

2019 ◽  
Vol 44 (1) ◽  
pp. 93-112 ◽  
Author(s):  
Khaled M Youssef ◽  
Ahmed M El Kholy ◽  
Ashraf M Hamed ◽  
Nabil A Mahmoud ◽  
Ahmed M El Baz ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Peak Power ◽  
Stokes Equations ◽  
Power Coefficient ◽  
Navier Stokes ◽  
Future Application ◽  
Speed Ratio ◽  
Ansys Fluent ◽  
Turbine Performance ◽  
Savonius Wind Turbine

This work presents an innovative technique to enhance the performance of the Savonius wind turbine. The new technique is based on introducing an upstream deflector and downstream baffle. The shape and location of both devices are optimized using a genetic algorithm. The performance of the turbine with the optimized devices is compared with the single Savonius turbine performance. The study employs the finite volume solver (ANSYS-FLUENT) to solve unsteady Reynolds Averaged Navier–Stokes equations and turbulence model equations. The optimized configuration results in much higher power coefficient than the Savonius turbine. The average peak power coefficient using both deflector and baffle is 0.47 compared to 0.24 of the Savonius turbine. The peak power coefficient of the turbine corresponds to a speed ratio close to unity. This improved performance is attributed to the favorable aerodynamic interaction between the turbine and the downstream baffle which accelerates the flow around the rotor and generates larger turning torque. The baffle generates a jet effect on the advancing bucket and accelerates the flow behind the bucket creating a large zone of negative pressure and thereby increases the driving torque. Furthermore, the upstream deflector (also called shield or curtain) produces a shield for the returning bucket of the turbine which diminishes the adverse effect associated with the returning bucket on the aerodynamic torque of the turbine. This remarkable improvement of turbine performance will encourage the future application of the Savonius wind turbine in small power applications of wind energy.

Numerical Research on the Characteristics of Lift-Drag Type Vertical Axis Wind Turbine

2012 ◽  
Vol 189 ◽  
pp. 448-452
Author(s):  
Yan Jun Chen ◽  
Guo Qing Wu ◽  
Yang Cao ◽  
Dian Gui Huang ◽  
Qin Wang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Chord Length ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Middle Range ◽  
Parabolic Form ◽  
Cfd Method

Numerical studies are conducted to research the performance of a kind of lift-drag type vertical axis wind turbine (VAWT) affected by solidity with the CFD method. Moving mesh technique is used to construct the model. The Spalart-Allmaras one equation turbulent model and the implicit coupled algorithm based on pressure are selected to solve the transient equations. In this research, how the tip speed ratio and the solidity of blade affect the power coefficient (Cp) of the small H-VAWT is analyzed. The results indicate that Cp curves exhibit approximate parabolic form with its maximum in the middle range of tip speed ratio. The two-blade wind turbine has the lowest Cp while the three-blade one is more powerful and the four-blade one brings the highest power. With the certain number of blades, there is a best chord length, and too long or too short chord length may reduce the Cp.

scholarly journals 361 Savonius wind turbine with wind concentrator : In case of tip speed ratio>1.0

2005 ◽  
Vol 2005 (0) ◽  
pp. 83-84
Author(s):  
Sheng Zhang ◽  
Takayuki Yaginuma ◽  
Masahiro Mino ◽  
Hiroyuki Ueno ◽  
Susumu Ishii
Keyword(s):  
Wind Turbine ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine

Savonius Wind Turbine Performances on Wind Concentrator

2017 ◽  
Vol 8 (1) ◽  
pp. 376
Author(s):  
Dygku. Asmanissa Awg. Osman ◽  
Norzanah Rosmin ◽  
Nor Shahida Hasan ◽  
Baharruddin Ishak ◽  
Aede Hatib Mustaamal@Jamal ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Electrical Power ◽  
Vertical Axis ◽  
Angular Speed ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Air Compressor ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine ◽  
Air Streams

The air streams from the outlet of an air compressor can be used to generate electricity. For instance, if a micro-sized Vertical-Axis Wind-Turbine (VAWT) is installed towards the airflow, some amount of electricity can be generated before being stored in a battery bank. The research’s objectives are to design, fabricate and analyze the performance of Helical Savonius VAWT blade rotors, which is tested with and without using a wind concentrator. The Helical Savonius VAWT is tested at 0 cm without the concentrator, whereas the blade rotor is tested at concave-blade position when using the concentrator. The blade and the wind concentrator designs were based on the dimensions and the constant airflow of the air compressor. The findings suggested that the blade produced its best performance when tested using wind concentrator at concave-blade position in terms of angular speed (<em>ω</em>), tip speed ratio (<em>TSR</em>) and the generated electrical power (<em>P</em><em><sub>E</sub></em>). The findings concluded that the addition of wind concentrator increases the airflow which then provided better performances on the blades.

Study on Performance and Flow Condition of a Cross-Flow Wind Turbine With a Symmetrical Casing

2011 ◽  
Vol 133 (5) ◽  
Author(s):  
Junichiro Fukutomi ◽  
Toru Shigemitsu ◽  
Hiroki Daito
Keyword(s):  
Wind Turbine ◽  
Rotational Speed ◽  
Flow Condition ◽  
Cross Flow ◽  
Low Noise ◽  
Maximum Power ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
The Cross

A cross-flow wind turbine has a high torque coefficient at a low tip speed ratio. Therefore, it is a good candidate for use as a self-starting turbine. Furthermore, it has low noise and excellent stability; therefore, it has attracted attention from the viewpoint of applications as a small wind turbine for an urban district. However, its maximum power coefficient is extremely low (10%) as compared to that of other small wind turbines. Prevailing winds in two directions often blow in urban and coastal regions. Therefore, in order to improve the performance and the flow condition of the cross-flow rotor, a casing suitable for this sort of prevailing wind conditions is designed in this research and the effect of the casing is investigated by experimental and numerical analysis. In the experiment, a wind tunnel with a square discharge is used and main flow velocity is set as 20 m/s. A torque meter, a rotational speed pickup, and a motor are assembled with the same axis as the test wind turbine and the tip speed ratio is changeable by a rotational speed controller. The casing is set around the cross-flow rotor and flow distribution at the rotor inlet and the outlet is measured by a one-hole pitot tube. The maximum power coefficient is obtained as Cpmax = 0.19 with the casing, however Cpmax = 0.098 without the casing. It is clear that the inlet and the outlet flow condition is improved by the casing. In the present paper, in order to improve the performance of a cross-flow wind turbine, a symmetrical casing suitable for prevailing winds in two directions is proposed. Then, the performance and the internal flow condition of the cross-flow wind turbine with the casing are clarified. Furthermore, the influence of the symmetrical casing on performance is discussed and the relation between the flow condition and performance is considered.

scholarly journals Numerical simulation and experimental study of blade pitch effect on Darrieus straight-bladed wind turbine with high solidity: A case study under realistic conditions

2020 ◽  
Author(s):  
Milad Babadi Soultanzadeh ◽  
Alireza Moradi
Keyword(s):  
Wind Turbine ◽  
Numerical Method ◽  
Pitch Angle ◽  
Numerical Results ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Regulation System ◽  
Lower Velocity ◽  
Realistic Condition ◽  
Tip Speed Ratio

Abstract Numerical and experimental studies were performed to examined the influence of pitch angle on the aerodynamic performance of a small Darrieus straight blade vertical axis wind turbine with high solidity and pitch regulation system under a realistic condition. By comparing experimental and numerical results, numerical results were validated. The power coefficient was measured and calculated at different tip speed ratios and for two pitch angles 0 and 5. The results revealed that 5 degrees increase in the pitch angle led to 25% elevation in the maximum value of the power coefficient (performance coefficient). Also, the numerical results showed higher accuracy at lower tip speed ratios for both pitch angles. After numerical method validation, numerical method employed to calculate the coefficient of performance and coefficient of torque function of Azimuth position as well as the flow field in the rotor affected zone and lateral distance. According to the numerical results, vorticity generation increased by the rise in the pitch angle at a constant tip speed ratio; the maximum performance coefficient occurred at a lower tip speed ratio with elevation in the pitch angle; finally, the increment in the pitch angle led to lower velocity profile in lateral distances of the rotor.

scholarly journals STUDI EKSPERIMENTAL PERFORMANSI TURBIN SAVONIUS DI PESISIR PANTAI KABUPATEN DEMAK TERHADAP DAYA LISTRIK YANG DIHASILKAN

2021 ◽  
Vol 14 (1) ◽  
pp. 16
Author(s):  
Wahyu Santoso ◽  
Herman Saputro ◽  
Husin Bugis
Keyword(s):  
Renewable Energy ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Raw Material ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Generator Type ◽  
Wind Potential ◽  
Savonius Wind Turbine

<p><em>Energy from fossil fuels consisting of petroleum, coal, natural gas containing raw material for energy fulfillment in Indonesia is still very central through the use of raw materials from renewable energy is still very low. In Indonesia the potential for renewable energy such as wind energy needs to be optimized. One of the uses of wind energy is through savonius wind turbine as electricity generators. Characteristics of savonius wind turbine with vertical axis rotors which gave a simple shape, and that able to control low speeds. This is in accordance with regions in Indonesi which have low average speeds.         This experimental study, aims to determine the description of wind potential and determine the performance of savonius wind turbines on the coast of Demak regency on the electrical energy produced. Savonius wind turbine used is made of galvalum material in the form of an S type rotor with diameter 1.1 m and height 1.4 m, using pulley transmission system with multiplication ratio 1:6 dan using generator type PMG 200 W. This research uses the method experiment. Data collection in the form of wind speed, humidity, temperature, rotor rotation speed, voltage and electric curret is carried out at 14.30 to 17.30 Western Indonesian Time. Data Analysis in this study uses quantitative descriptive analysis. The result showed the potential of wind on the coast of Demak regency have an average wind speed of 2,02 m/s with a temperature of 31</em><em>,</em><em>34 </em><em><sup>0</sup></em><em>C and humidity of 76,96. And the performance of the installed wind turbine produces the highest power 3.5 watt with an electric power coefficient of 0,181 and tip speed ratio around 1,75. From these result, the potensial of wind with performance savonius turbine can generate electricity used for pond lighting in the village Berahan Kulon Kecamatan Wedung. </em><em></em></p>

Sign in / Sign up

Export Citation Format

Share Document