scholarly journals Characterization of plasma sprayed deposits : influence of process parameters

2007 ◽  
Author(s):  
Zdenek Prochazka
Keyword(s):  
Process Parameters ◽  
Influence Of Process Parameters ◽  
Plasma Sprayed

Characterization of Tar from the Pyrolysis/Gasification of Refuse Derived Fuel: Influence of Process Parameters and Catalysis

2012 ◽  
Vol 26 (4) ◽  
pp. 2107-2115 ◽  
Author(s):  
Paula H. Blanco ◽  
Chunfei Wu ◽  
Jude A. Onwudili ◽  
Paul T. Williams
Keyword(s):  
Process Parameters ◽  
Influence Of Process Parameters ◽  
Refuse Derived Fuel

Optimization of Process Parameters for Plasma Sprayed HA/ZrO2 Bioceramic Coating

2012 ◽  
Vol 161 ◽  
pp. 269-273
Author(s):  
Yu Mei Bao ◽  
Lei Wu ◽  
Li Jie Weng
Keyword(s):  
Mechanical Property ◽  
Composite Coating ◽  
Process Parameters ◽  
Bonding Strength ◽  
Measurement Methods ◽  
Influence Of Process Parameters ◽  
Optimization Of Process Parameters ◽  
Property Measurement ◽  
Titanium Alloy Substrate ◽  
Plasma Sprayed

Preparation and mechanical property measurement methods of bioceramic coating are introduced. HA/ZrO2 composite coating was prepared in the titanium alloy substrate with Plasma spraying equipment, and its bonding strength was measured. The influence of process parameters on bonding strength of plasma-sprayed HA/ZrO2 composite coating is simulated with computing software Mathematica and optimized.

Investigation on Inconel 625 Alloy Thin-Walled Parts by Direct Laser Fabrication

2011 ◽  
Vol 189-193 ◽  
pp. 3687-3691 ◽  
Author(s):  
Shi You Gao ◽  
Ye Fei Zhou ◽  
Ming Zhe Xi
Keyword(s):  
Process Parameters ◽  
Inconel 625 ◽  
Influence Of Process Parameters ◽  
Scanning Velocity ◽  
Laser Fabrication ◽  
Direct Laser ◽  
Inconel 625 Alloy ◽  
Direct Laser Fabrication ◽  
Thin Walled

In this paper, the process of direct laser fabricating (DLF) thin-walled parts with Inconel 625 alloy was studied. The interrelationship between deposition quality and process parameters has been analyzed in the aspects of laser power. Scanning velocity, powder feed velocity, z-increment. The further investigations of study lie on the influence of process parameters on geometrical characterization of single cladding layer, the Axis-Z increments on height of thin-walled part, as well as the microstructure of fabricated sample of Inconel 625. The results based on above experiments show that the Inconel 625 alloy parts can be fabricated by direct laser fabrication method and the samples were fully dense, homogenous and free of defects with the parameters under a certain range.

Characterization Of An EBL System: The Influence Of Process Parameters On Thickness Resist And Engraving Shapes

2011 ◽  
Author(s):  
G. D’Urso ◽  
M. Longo ◽  
C. Ravasio ◽  
G. Maccarini ◽  
Francisco Chinesta ◽  
...  
Keyword(s):  
Process Parameters ◽  
Influence Of Process Parameters

CHARACTERIZATION OF AS-SPRAYED AND LASER-TREATED ZIRCONIA-BASED PLASMA SPRAYED COATINGS

1990 ◽  
Vol 51 (C5) ◽  
pp. C5-393-C5-402
Author(s):  
A. FERRIERE ◽  
G. FLAMANT ◽  
J.-F. ROBERT ◽  
P. PEKSHEV ◽  
I. SMUROV ◽  
...  
Keyword(s):  
Plasma Sprayed Coatings ◽  
Plasma Sprayed ◽  
Sprayed Coatings
Sign in / Sign up

Export Citation Format

Share Document