Experimental and numerical study on the solar gain and heat loss of typical existing and refurbished German buildings

2020 ◽  
pp. 75-93
Author(s):  
Peter Steininger ◽  
Matthias Gaderer ◽  
Belal Dawoud
Keyword(s):  
Thermal Conductivity ◽  
Numerical Study ◽  
Thermal Conductance ◽  
Estimation Procedure ◽  
Heat Transfer Process ◽  
Simulation Software ◽  
Heat Losses ◽  
Solar Simulator ◽  
Typical Structure ◽  
Existing Building

This communication introduces an experimental setup for investigating the effect of solar radiation on the reduction of transmission heat losses and the steady state thermal conductance of uninsulated and insulated multi-layer wall samples. The setup consists of two adjacent climatic chambers, which share a common wall, in which the multi-layer wall samples are mounted. A solar simulator is applied within the outdoor air climatic chamber, whose radiation spectrum and radiation intensity are approximately equivalent to those of the sun. The first tests have been carried out on a wall sample with a typical structure of existing buildings from the year 1930 in Germany. In addition, a high-performance insulating plaster layer has been applied on a basic test sample (with existing building structure) to replicate and assess the refurbished scenario. Furthermore, a numerical investigation on the transient heat transfer process is carried out by using the simulation software COMSOL Multiphysics®. The experimental results of both uninsulated and insulated wall samples are validated against 1D and 3D models. As seen, the uninsulated wall, whose thermal conductance was experimentally determined to be equal to 1.79 W/(m²K), absorbs a heat flux of 208 W/m² through its external wall surface over a period of 8 hours. A fraction of 9.8 % of the absorbed heat arrives as a gain on the internal wall and reduces the transmission heat losses by 11.7 % over a period of 55 hours. On the other hand, the thermal conductivity of the insulation layer of the refurbished wall sample with micro hollow glass spheres was estimated by a parameter estimation procedure using the 3D model and the obtained experimental data. Using the estimated thermal conductivity, a thermal conductance of 0.42 W/(m²K) has been obtained for the refurbished wall sample.

A Numerical Study on Heat Conductivity Characterization of Aluminium Filled Polypropylene Composites

2012 ◽  
Vol 585 ◽  
pp. 14-18 ◽  
Author(s):  
Alok Agrawal ◽  
Alok Satapathy
Keyword(s):  
Thermal Conductivity ◽  
Finite Element ◽  
Volume Fraction ◽  
Numerical Study ◽  
Three Dimensional ◽  
Heat Transfer Process ◽  
Aluminium Content ◽  
Volume Percentage ◽  
Polypropylene Composites ◽  
Finite Element Package

A numerical simulation of the heat-transfer process within polypropylene matrix composite filled with micro-sized aluminium particles using Finite Element Method is proposed in this paper. Three-dimensional spheres-in-cube lattice array models are constructed to simulate the microstructure of composite materials with aluminium content ranging from about 1.5 to 42 vol% and the effective thermal conductivities of the composites are estimated. A commercially available finite-element package ANSYS is used for this numerical analysis. The result shows that the effective thermal conductivity (Keff) increases with increase in the volume fraction of the aluminium in the composites. The simulated values are compared with calculated Keff values obtained from other established correlations such as Rule-of-Mixture (ROM), Maxwell’s model and with published experimental results. This study reveals that the incorporation of aluminium particles results in enhancement of thermal conductivity of polypropylene thereby increasing its heat transportation capability. It is found that with incorporation of about 42 vol% of 100 micron sized aluminium particles thermal conductivity of the composite increases from 0.239 W/m-K to 0.875 W/m-K. This study also shows that the effect of particle size with same volume percentage on thermal conductivity is marginal.

Moving Sheet With Variable Thermal Conductivity Emerging From a Slot

2007 ◽  
Author(s):  
O. Bautista ◽  
E. Bautista ◽  
F. Me´ndez
Keyword(s):  
Thermal Conductivity ◽  
Thermal Conductance ◽  
Variable Thermal Conductivity ◽  
Heat Transfer Process ◽  
Point Of View ◽  
Dimensional Parameter ◽  
Parameter Identifying ◽  
Longitudinal Coordinate ◽  
Transverse Temperature ◽  
Non Linear System

In this work, we treat the heat transfer process of a continuously moving flat sheet with variable thermal conductiviy, emerging from a slot in contact with a quiescent fluid. Due to the thermal conductivity of the sheet, strong longitudinal and transverse temperature gradients arise within it, requiring to solve simultaneously the energy equation of the sheet and fluid equations. The momentum and energy balance equations are reduced to a non-linear system of partial differential equations with four parameters: the Prandtl number, Pr, a non-dimensional sheet thermal conductance β, a non-dimensional parameter identifying the effect of the variable thermal conductivity γ and a suitable Peclet number, Pe. For finite values of the parameter γ we recognize the limits β≪1 and βPe2≪1 as the most relevant from a practical point of view. In this case, the problem is governed by an universal integro-differential equation in order to obtain the spatial evolution of the sheet temperature as a function of the nondimensional longitudinal coordinate.

Experimental and numerical study for effective thermal conductivity of metallic honeycomb sandwich structures

2020 ◽  
pp. 109963622093353
Author(s):  
Rongnan Yuan ◽  
Shouxiang Lu
Keyword(s):  
Thermal Conductivity ◽  
Effective Thermal Conductivity ◽  
Sandwich Structure ◽  
Sandwich Structures ◽  
Numerical Study ◽  
Heat Transfer Process ◽  
Heat Radiation ◽  
Honeycomb Sandwich ◽  
Essential Parameter ◽  
Honeycomb Sandwich Structure

Effective thermal conductivity is an essential parameter to investigate thermal properties of metallic honeycomb sandwich structures. And it cannot be measured by traditional methods due to sandwich structure imbedded with air. A practical experimental equipment was designed to evaluate the value under different temperature from 100°C to 400°C. And it was found that the value of effective thermal conductivity can also be calculated by knowing the thermal conductivity of the reference, thickness of the reference and the slope and intercept of temperature in different layers. Meanwhile, numerical simulation was conducted and the results agreed well with that achieved by experiment. Also, the value of effective thermal conductivity calculated by experiment is close to the value calculated by Swann-Pittman empirical equation. And the method is not limited in metallic honeycomb sandwich structure while it can be applied in most structures with amounts of air. On that basis, heat transfer process of the structure is discussed including heat conduction, heat convection and heat radiation.

scholarly journals A Computational Study on the Role of Parameters for Identification of Thyroid Nodules by Infrared Images (and Comparison with Real Data)

Sensors ◽  
2021 ◽  
Vol 21 (13) ◽  
pp. 4459
Author(s):  
José R. González ◽  
Charbel Damião ◽  
Maira Moran ◽  
Cristina A. Pantaleão ◽  
Rubens A. Cruz ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thyroid Nodules ◽  
Numerical Study ◽  
Computational Study ◽  
Internal Heat ◽  
Heat Transfer Process ◽  
The Body ◽  
Physical Parameters ◽  
Infrared Sensors ◽  
Wide Range

According to experts and medical literature, healthy thyroids and thyroids containing benign nodules tend to be less inflamed and less active than those with malignant nodules. It seems to be a consensus that malignant nodules have more blood veins and more blood circulation. This may be related to the maintenance of the nodule’s heat at a higher level compared with neighboring tissues. If the internal heat modifies the skin radiation, then it could be detected by infrared sensors. The goal of this work is the investigation of the factors that allow this detection, and the possible relation with any pattern referent to nodule malignancy. We aim to consider a wide range of factors, so a great number of numerical simulations of the heat transfer in the region under analysis, based on the Finite Element method, are performed to study the influence of each nodule and patient characteristics on the infrared sensor acquisition. To do so, the protocol for infrared thyroid examination used in our university’s hospital is simulated in the numerical study. This protocol presents two phases. In the first one, the body under observation is in steady state. In the second one, it is submitted to thermal stress (transient state). Both are simulated in order to verify if it is possible (by infrared sensors) to identify different behavior referent to malignant nodules. Moreover, when the simulation indicates possible important aspects, patients with and without similar characteristics are examined to confirm such influences. The results show that the tissues between skin and thyroid, as well as the nodule size, have an influence on superficial temperatures. Other thermal parameters of thyroid nodules show little influence on surface infrared emissions, for instance, those related to the vascularization of the nodule. All details of the physical parameters used in the simulations, characteristics of the real nodules and thermal examinations are publicly available, allowing these simulations to be compared with other types of heat transfer solutions and infrared examination protocols. Among the main contributions of this work, we highlight the simulation of the possible range of parameters, and definition of the simulation approach for mapping the used infrared protocol, promoting the investigation of a possible relation between the heat transfer process and the data obtained by infrared acquisitions.

Numerical Study on the Effect of Inner Tube Position on Heat Transfer Process in Self-Recuperative Radiant Tube

2011 ◽  
Vol 228-229 ◽  
pp. 676-680 ◽  
Author(s):  
Ye Tian ◽  
Xun Liang Liu ◽  
Zhi Wen
Keyword(s):  
Heat Transfer ◽  
Transfer Process ◽  
Numerical Study ◽  
Flame Temperature ◽  
Three Dimensional ◽  
Mathematic Model ◽  
Heat Transfer Process ◽  
Bulk Temperature ◽  
Radiant Tube ◽  
Peak Value

A three-dimensional mathematic model is developed for a 100kw single-end recuperative radiant tube and the simulation is performed with the CFD software FLUENT. Also it is used to investigate the effect of distance between combustion chamber exit and inner tube on heat transfer process. The results suggest that the peak value of combustion flame temperature drops along with the increasing of distance, which leads to low NOX discharging. Also radiant tube surface bulk temperature decreases, which causes radiant tube heating performance losses.

scholarly journals Thermal conductivity and deformation of Taxodium hybrid ‘Zhongshanshan’ during heat transfer process

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 2645-2655
Author(s):  
Yuehua Zhu ◽  
Yaoli Zhang ◽  
Biao Pan
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Moisture Content ◽  
Transfer Process ◽  
Dimensional Change ◽  
Testing Temperature ◽  
Scientific Basis ◽  
Heat Transfer Process ◽  
Wood Moisture Content ◽  
Wood Moisture

The thermal conductivity and the deformation of wood from the Taxodium hybrid ‘Zhongshanshan’ were studied in the process of heat transfer. The results showed that the average thermal conductivity of this wood was 0.1257 W/(m·K) under the condition of 12% wood moisture content and 30 °C heat transfer temperature. When the testing temperature exceeded 0 °C, the thermal conductivity increased linearly with both temperature and wood moisture content and was affected by the moisture content of the wood. During the heat transfer process, the deformation of features caused repeated swelling and shrinkage in the longitudinal, radial, and tangential directions. The dimensional change was greatly affected by the wood’s moisture content and was less affected by the temperature. These results are of great meaning for the study of the heat transfer process of Taxodium hybrid ‘Zhongshanshan’ wood. Furthermore, it provides a scientific basis for the heat preservation effect, drying treatment, and pyrolysis treatment of Taxodium hybrid ‘Zhongshanshan’ wood for use as a building material.

scholarly journals Hygrothermal simulation of building performance: data for Scottish masonry materials

2021 ◽  
Vol 54 (4) ◽  
Author(s):  
P. F. G. Banfill
Keyword(s):  
Thermal Conductivity ◽  
Water Vapour ◽  
Material Properties ◽  
Simulation Software ◽  
Water Vapour Permeability ◽  
High Porosity ◽  
Water Absorption Coefficient ◽  
Vapour Permeability ◽  
Hygrothermal Simulation ◽  
Current Production

AbstractRetrofitting thermal insulation to solid masonry walls alters their hygrothermal behaviour, which can be modelled by hygrothermal simulation software. However, such software needs values of key material properties to ensure satisfactory results and until now data has not been available for Scottish masonry buildings. This work aims to contribute to a Scotland-specific dataset of material properties for use by designers working on such buildings. Thermal conductivity, water vapour permeability, sorptivity, water absorption coefficient, hygroscopic sorption, density and porosity were all determined experimentally for selected historic and contemporary masonry materials. Within the range of materials tested three groups of materials properties emerge. Natural hydraulic lime mortars, hot-mixed quicklime mortar and earth mortar all show comparatively low density, high porosity, low thermal conductivity, high water vapour permeability and variable but generally high hygroscopic sorption. Craigleith, Hailes and Giffnock sandstones, no longer available but obtained from conservation works on historic buildings, and Locharbriggs and Hazeldean sandstones, obtained from current production, all show intermediate values of these properties. Crathes granodiorite and Scottish whinstone (from current production) show high density, low porosity, high thermal conductivity, low water vapour permeability and low hygroscopic sorption. It is shown that these materials are all relevant to Scottish buildings constructed in traditional masonry and this paper presents the first comprehensive set of hygrothermal property data for them.

Sign in / Sign up

Export Citation Format

Share Document