Detection of delamination in laminated CFRP composites using eddy current testing: Simulation and experimental study

2018 ◽  
Vol 57 (2) ◽  
pp. 177-192 ◽  
Author(s):  
Xiaojuan Xu ◽  
Hongli Ji ◽  
Jinhao Qiu ◽  
Toshiyuki Takagi
Keyword(s):  
Experimental Study ◽  
Eddy Current ◽  
Eddy Current Testing ◽  
Current Testing ◽  
Cfrp Composites

scholarly journals Experimental Study of Microstructures in Bias Weld of Coiled Tubing Steel Strip With Multi-Frequency Eddy Current Testing

IEEE Access ◽  
2020 ◽  
Vol 8 ◽  
pp. 48241-48251
Author(s):  
Zhaoming Zhou ◽  
Mian Qin ◽  
Yuedong Xie ◽  
Jinsong Tan ◽  
Hailong Bao
Keyword(s):  
Experimental Study ◽  
Eddy Current ◽  
Steel Strip ◽  
Eddy Current Testing ◽  
Current Testing ◽  
Coiled Tubing

Simulation and experimental study of remote field eddy current testing on flat conductive plate

2010 ◽  
Vol 33 (3-4) ◽  
pp. 1261-1266 ◽  
Author(s):  
Haitao Wang ◽  
Qiufeng Luo ◽  
Xin Wang ◽  
Guiyun Tian ◽  
Lidong Xing ◽  
...  
Keyword(s):  
Experimental Study ◽  
Eddy Current ◽  
Eddy Current Testing ◽  
Current Testing ◽  
Conductive Plate

Probabilistic evaluation of detection capability of eddy current testing to inspect pitting on a stainless steel clad using multiple signal features

2020 ◽  
Vol 64 (1-4) ◽  
pp. 47-55
Author(s):  
Takuma Tomizawa ◽  
Haicheng Song ◽  
Noritaka Yusa
Keyword(s):  
Stainless Steel ◽  
Eddy Current ◽  
Pressure Vessels ◽  
Eddy Current Testing ◽  
Probability Of Detection ◽  
Current Testing ◽  
Multiple Signal ◽  
Signal Features ◽  
Inner Surface ◽  
Drill Holes

This study proposes a probability of detection (POD) model to quantitatively evaluate the capability of eddy current testing to detect flaws on the inner surface of pressure vessels cladded by stainless steel and in the presence of high noise level. Welded plate samples with drill holes were prepared to simulate corrosion that typically appears on the inner surface of large-scale pressure vessels. The signals generated by the drill holes and the noise caused by the weld were examined using eddy current testing. A hit/miss-based POD model with multiple flaw parameters and multiple signal features was proposed to analyze the measured signals. It is shown that the proposed model is able to more reasonably characterize the detectability of eddy current signals compared to conventional models that consider a single signal feature.

scholarly journals Research on Detection Mechanism of Weld Defects of Carbon Steel Plate Based on Orthogonal Axial Eddy Current Probe

Sensors ◽  
2020 ◽  
Vol 20 (19) ◽  
pp. 5515
Author(s):  
Linnan Huang ◽  
Chunhui Liao ◽  
Xiaochun Song ◽  
Tao Chen ◽  
Xu Zhang ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Eddy Current ◽  
Steel Plate ◽  
Difficult Problem ◽  
Eddy Current Testing ◽  
Detection Sensitivity ◽  
Detection Mechanism ◽  
Current Testing ◽  
Weld Defects ◽  
Lift Off

The uneven surface of the weld seam makes eddy current testing more susceptible to the lift-off effect of the probe. Therefore, the defect of carbon steel plate welds has always been a difficult problem in eddy current testing. This study aimed to design a new type of eddy current orthogonal axial probe and establish the finite element simulation model of the probe. The effect of the probe structure, coil turns, and coil size on the detection sensitivity was simulated. Further, a designed orthogonal axial probe was used to conduct a systematic experiment on the weld of carbon steel specimens, and the 0.2 mm width and 1 mm depth of weld defects of carbon steel plates were effectively detected. The experimental results showed that the new orthogonal axial eddy current probe effectively suppressed the unevenness effect of the weld surface on the lift-off effect during the detection process.

scholarly journals Evaluation of Coating Thickness Using Lift-Off Insensitivity of Eddy Current Sensor

Sensors ◽  
2021 ◽  
Vol 21 (2) ◽  
pp. 419
Author(s):  
Xiaobai Meng ◽  
Mingyang Lu ◽  
Wuliang Yin ◽  
Abdeldjalil Bennecer ◽  
Katherine J. Kirk
Keyword(s):  
Eddy Current ◽  
Coating Thickness ◽  
Thickness Measurement ◽  
Eddy Current Testing ◽  
Thickness Variation ◽  
Testing Technique ◽  
Current Testing ◽  
Thin Skin ◽  
Embedded Algorithms ◽  
Lift Off

Defect detection in ferromagnetic substrates is often hampered by nonmagnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of nonmagnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multifrequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3% for an extended lift-off range of up to 10 mm.

Differential coupling double-layer coil for eddy current testing with high lift-off

2021 ◽  
pp. 1-1
Author(s):  
Kefan Chen ◽  
Bin Gao ◽  
G.Y. Tian ◽  
Yupei Yang ◽  
Changrong Yang ◽  
...  
Keyword(s):  
Double Layer ◽  
Eddy Current ◽  
Eddy Current Testing ◽  
High Lift ◽  
Current Testing ◽  
Lift Off ◽  
Differential Coupling
Sign in / Sign up

Export Citation Format

Share Document