scholarly journals FE analysis of cruciform welded joints considering different mechanical properties for base material, heat affected zone and weld metal

2014 ◽  
Vol 8 (30) ◽  
pp. 304-310 ◽  
Author(s):  
Pasqualino Corigliano ◽  
Vincenzo Crupi ◽  
Eugenio Guglielmino ◽  
Wolfgang Fricke
Keyword(s):  
Mechanical Properties ◽  
Weld Metal ◽  
Heat Affected Zone ◽  
Welded Joints ◽  
Base Material ◽  
Fe Analysis

scholarly journals DIFFUSION OF HYDROGEN IN WELDED JOINTS OF STRUCTURAL STEELS

2017 ◽  
Vol 21 (6) ◽  
pp. 85-95 ◽  
Author(s):  
N. N. Sergeev ◽  
A. N. Sergeev ◽  
S. N. Kutepov ◽  
A. E. Gvozdev ◽  
E. V. Ageev
Keyword(s):  
Diffusion Coefficient ◽  
Weld Metal ◽  
Heat Affected Zone ◽  
Welded Joints ◽  
Chemical Potential ◽  
Weld Zone ◽  
Base Material ◽  
High Strength ◽  
Low Alloy Steels ◽  
Alloy Steels

High-strength low-alloy steels are widely used in the construction of welded metal structures. The main advantage of these steels is good combination of strength and toughness, and weldability. However, when welding high strength low alloy steels during cooling of the weld to a temperature below 150-100 °C there may be a risk of formation of bulk crystal structures defects in the weld zone - cold cracks. It was experimentally established that one of the factors contributing to the formation of cold cracks may be the occlusion of hydrogen in the atmosphere of arc plasma in the solidifying weld metal, from which diffusion hydrogen may diffuse to different areas of the weld after cooling. Hydrogen cracking typically has a tendency to slow down i.e. cracks can occur several days after the completion of welding process. As a rule, hydrogen induced cracking occurs either in the original steel in the heat-affected zone or in the weld metal, which is important, topical and long been researched by various scientific schools. Modern technologies of high strength low alloy steels processing have significantly improved the quality of the base material by reducing the amount of carbon and impurities, which has increased the stability of weld in the heat affected zone (HAZ) to hydrogen induced cold cracking. The paper presents modern approaches to the definition of diffusion coefficient of hydrogen in welded joints of high-strength low-alloy steels. Taking into account the temperature, the gradient of chemical potential and continuity conditions there has been considered the process of mass transfer of hydrogen under the influence of diffuse inhomogeneous mediums. It has been shown that the local effects of changing pressure and chemical potential are described using the equation of generalized potential of the diffusing substance. Our paper presents analytical expressions to determine the apparent diffusion coefficient of hydrogen in different local areas of a welded joint depending on temperature.

scholarly journals Microstructure and Mechanical Properties of Modern 11%Cr Heat-Resistant Steel Weld Joints

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3430
Author(s):  
Grzegorz Golański ◽  
Jacek Słania ◽  
Marek Sroka ◽  
Paweł Wieczorek ◽  
Michał Urzynicok ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Welded Joints ◽  
Martensitic Steel ◽  
Base Material ◽  
Hardness Measurement ◽  
Power Industry ◽  
Strength Properties ◽  
Typical Structure ◽  
Δ Ferrite ◽  
The Impact

In addition to good high-temperature creep resistance and adequate heat resistance, steels for the power industry must have, among other things, good weldability. Weldability of such steels is one of the criteria determining whether or not the material is suitable for applications in the power industry. Therefore, when materials such as martensitic steel Thor 115 (T115) are introduced into the modern power industry, the quality and properties of welded joints must be assessed. The paper presents the results of metallographic and mechanical investigations of T115 martensitic steel welded joints. The analysis was carried out on joints welded with two filler metals: WCrMo91 (No. 1) and EPRI P87 (No. 2). The scope of the investigations included: microstructural investigations carried out using optical, scanning and transmission electron microscopy and mechanical testing, i.e., Vickers microhardness and hardness measurement, static tensile test and impact test. The macro- and microstructural investigations revealed correct structure of the weld, without welding imperfections. The microstructural investigations of joint No. 1 revealed a typical structure of this type of joint, i.e., the martensitic structure with numerous precipitates, while in joint No. 2, the so-called Nernst’s layers and δ-ferrite patches were observed in the weld fusion zone as well as the heat affected zone (HAZ). The mechanical properties of the test joints met the requirements for the base material. A slight influence of the δ-ferrite patch on the strength properties of joint No. 2 was observed, and its negative effect on the impact energy of HAZ was visible.

Effect of Post Weld Heat Treatment on Fusion and Heat Affected Zone Microstructure and Mechanical Properties of Inconel X-750 Welds

2011 ◽  
Vol 214 ◽  
pp. 108-112 ◽  
Author(s):  
Prachya Peasura ◽  
Bovornchok Poopat
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Grain Boundary ◽  
Weld Metal ◽  
Heat Affected Zone ◽  
Aging Temperature ◽  
Post Weld Heat Treatment ◽  
High Aging Temperature ◽  
Zone Microstructure

The Inconel X-750 indicates good hot corrosion resistance, high stability and strength at high temperatures and for this reason the alloy is used in manufacturing of gas turbine hot components. The objective of this research was study the effect of post weld heat treatment (PWHT) on fusion zone and heat affected zone microstructure and mechanical properties of Inconel X-750 weld. After welding, samples were solutionized at 1500 0C. Various aging temperature and times were studied. The results show that aging temperature and time during PWHT can greatly affect microstructure and hardness in fusion zone and heat affected zone. As high aging temperature was used, the grain size also increased and M23C6 at the grain boundary decreased. This can result in decreased of hardness. Moreover excessive aging temperature can result in increasing MC carbide intensity in parent phase (austenite). It can also be observed that M23C6 at the grain boundary decreased due to high aging temperature. This resulted in decreasing of hardness of weld metal and heat affected zone. Experimental results showed that the aging temperature 705 0C aging time of 24 hours provided smaller grain size, suitable size and intensity of MC carbide resulting in higher hardness both in weld metal and HAZ.

Microstructures and Mechanical Properties of Welded Joints of Several High Tensile Strength Steel

2018 ◽  
Vol 941 ◽  
pp. 224-229
Author(s):  
Takahiro Izumi ◽  
Tatsuya Kobayashi ◽  
Ikuo Shohji ◽  
Hiroaki Miyanaga
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Weld Metal ◽  
Welded Joints ◽  
Welded Joint ◽  
Steel Plates ◽  
Fatigue Properties ◽  
High Tensile Strength ◽  
The Matrix ◽  
Microstructures And Mechanical Properties

Microstructures and mechanical properties of lap fillet welded joints of several high and ultra-high tensile strength steel by arc welding were investigated. Steel plates having tensile strength of 400 (SPH400W), 590 (SPC590Y, SPC590R), 980 (SPC980Y) and 1500 MPa (SAC1500HP) class with 2 mm thickness were prepared. Four types of joints were formed by MAG welding; SPH400W/SPH400W, SPC590Y/SPC590Y, SPC980Y/SPC980Y and SAC1500HP/SPC590R. In joints with SPC590Y, SPC980Y and SAC1500HP steel which matrixes are martensitic microstructures, the HAZ softens due to transformation of martensite into ferrite with precipitating cementite. By using high and ultra-high tensile strength steel, the weld metal is strengthened due to dilution of the matrix into the weld metal and thus tensile shear strength of the welded joint increases. In the fatigue test, similar S-N diagrams were obtained in the all welded joints investigated. It seems that the effect of stress concentration due to the shape of the welded joint on fatigue properties is larger than that of the strength of the matrix.

Measurement of Weld Mechanical Properties Using an Instrumented Indentation Technique

2017 ◽  
Vol 754 ◽  
pp. 383-386
Author(s):  
Kee Nam Song
Keyword(s):  
Mechanical Properties ◽  
Heat Affected Zone ◽  
Weld Zone ◽  
Base Material ◽  
Metal Structure ◽  
Instrumented Indentation ◽  
Welded Structures ◽  
Indentation Technique ◽  
Lower Confidence ◽  
Welded Structure

Different microstructures in the weld zone of a metal structure including a fusion zone and a heat affected zone, are formed as compared to the base material. Consequently, the mechanical properties in the weld zone are different from those in the base material to a certain degree owing to different microstructures and residual welding stresses. When a welded structure is loaded, the mechanical behavior of the welded structure might be different from the case of a structure with homogeneous mechanical properties. It is known that obtaining the mechanical properties in the weld is generally difficult owing to the narrow regions of the weld and interfaces. As an alternative way to obtain the weld mechanical properties, the weld mechanical properties of Alloy800HT, SUS316L, and Alloy617, were recently measured using an instrumented indentation technique, and the representative weld mechanical properties of these materials were estimated with a 95% lower confidence level for later structural analyses of the welded structures.

Characterization of Local Deformation in Welded Joints Using a Combined Experimental and Numerical Approach

2014 ◽  
Vol 627 ◽  
pp. 241-244 ◽  
Author(s):  
Pawel Kucharczyk ◽  
Sebastian Münstermann
Keyword(s):  
Chemical Composition ◽  
Weld Metal ◽  
Welded Joints ◽  
Base Material ◽  
Welding Process ◽  
Numerical Approach ◽  
Geometrical Model ◽  
Local Deformation ◽  
Heat Treated ◽  
Welded Structure

The microstructure of welded joints differs significantly from that of the base material, what changes their mechanical properties and influences fatigue life. The aim of this work was the investigation of the local deformation field within a butt joint made of 10 mm thick structural steel S355. However, a direct sampling even of the weld metal was impossible due to small dimensions of butt joints. Therefore, the following procedure was utilized in order to manufacture big samples of the microstructure identical to that of the local weldment areas.A geometrical model of the welded structure describing the relevant areas e.g. weld metal, heat-affected zone was established. It was based on the results of the metallographic investigations, hardness mapping and electron-probe-micro-analysis of the local chemical composition. The welding process was numerically simulated using SYSWELD program to estimate the time-temperature-transition (TTT) curves for each identified area. The parameters of the heat input source were calibrated. Afterwards, the material of the defined chemical composition was heat-treated according to the TTT curves. For the validation purpose the heat-treated work pieces were evaluated in terms of microstructure and hardness distribution. Finally, the up-scaled samples of the respective bulk microstructure were manufactured and investigated in monotonic tests.

scholarly journals Application of Dynamic Beam Positioning for Creating Specified Structures and Properties of Welded Joints in Electron-Beam Welding

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2233
Author(s):  
Tatyana Olshanskaya ◽  
Vladimir Belenkiy ◽  
Elena Fedoseeva ◽  
Elena Koleva ◽  
Dmitriy Trushnikov
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Weld Metal ◽  
Thermal Effect ◽  
Welded Joints ◽  
Electron Beam Welding ◽  
Welded Joint ◽  
Parent Metal ◽  
Cooling Rates ◽  
Structures And Properties

The application of electron beam sweep makes it possible to carry out multifocal and multi-beam welding, as well as combine the welding process with local heating or subsequent heat treatment, which is important when preparing products from thermally-hardened materials. This paper presents a method of electron beam welding (EBW) with dynamic beam positioning and its experimental-calculation results regarding the formation of structures and properties of heat-resistant steel welded joints (grade of steel 20Cr3MoWV). The application of electron beam oscillations in welding makes it possible to change the shape and dimensions of welding pool. It also affects the crystallization and formation of a primary structure. It has been established that EBW with dynamic beam positioning increases the weld metal residence time and the thermal effect zone above the critical A3 point, increases cooling time and considerably reduces instantaneous cooling rates as compared to welding without beam sweep. Also, the difference between cooling rates in the depth of a welded joint considerably reduces the degree of structural non-uniformity. A bainitic–martensitic structure is formed in the weld metal and the thermal effect zone throughout the whole depth of fusion. As a result of this structure, the level of mechanical properties of a welded joint produced from EBW with dynamic electron beam positioning approaches that of parent metal to a greater extent than in the case of welding by a static beam. As a consequence, welding of heat-resistant steels reduces the degree of non-uniformity of mechanical properties in the depth of welded joints, as well as decreases the level of hardening of a welded joint in relation to parent metal.

scholarly journals Experimental Research and Numerical Simulation of Weld Repair with High Energy Spark Deposition Method

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 980 ◽  
Author(s):  
Yingjie Zhang ◽  
Kai Yang ◽  
Jianping Zhao
Keyword(s):  
Mechanical Properties ◽  
Numerical Simulation ◽  
Residual Stress ◽  
Heat Affected Zone ◽  
Welded Joints ◽  
High Energy ◽  
Repair Welding ◽  
Repair Processes ◽  
Repair Technology ◽  
Surface Repair

For long-serviced pressure equipment that is under severe working conditions such as a high temperature, high pressure, and corrosion, the material properties and structure will be unavoidably damaged or degraded, especially cracks and other damages at key positions such as welded joints, which seriously threaten the safe operation of the equipment. In order to promote the sustainable development of industries such as the chemical and petrochemical industries, remanufacturing technology has emerged worldwide, and various surface repair processes have also rapidly developed. As an important branch of surface repair technology, the high energy spark deposition (HESD) process is a new pulse cold welding repair technology developed from electro-spark deposition, which combines the advantages of multiple surface repair processes. The HESD process has the characteristics of a smaller heat affected zone and lower welding residual stress. It is a new type of repair method that is worthy of popularization and application. The process has been initially applied in the fields of surface modification and die steel repair. In this paper, the application of the HESD process to the repair of welded joints was introduced, the mechanical properties of the joints and the residual stress distribution after welding were analyzed, and the feasibility of HESD as a repair welding method for pressure structures was discussed. First, a numerical simulation of the temperature and stress field of HESD was proposed by using ABAQUS and the related subprograms, and the validity of the simulation results was verified by the residual stress test with the indentation strain method. Due to the precise control of the heat and pulse discharge working mode, the heat-affected zone and deformation caused by the HESD were extremely small, and the residual stress that was generated was low and only concentrated on the repair welding seam. Second, according to the numerical simulation and the test results of the mechanical properties of the welded joint, the optimal repair welding process parameters were obtained through the orthogonal experiment: peak current 45 A, pulse width 90 ms, and output voltage 10 V.

High Temperature, Low Cycle Fatigue Characterization of P91 Weld and Heat Affected Zone Material

2014 ◽  
Vol 136 (2) ◽  
Author(s):  
T. P. Farragher ◽  
S. Scully ◽  
N. P. O'Dowd ◽  
C. J. Hyde ◽  
S. B. Leen
Keyword(s):  
High Temperature ◽  
Weld Metal ◽  
Heat Affected Zone ◽  
Low Cycle Fatigue ◽  
Base Material ◽  
Strain Response ◽  
Cycle Fatigue ◽  
Stress Strain ◽  
Weld Material ◽  
The Cross

The high temperature low cycle fatigue behavior of P91 weld metal (WM) and weld joints (cross-weld) is presented. Strain-controlled tests have been carried out at 400 °C and 500 °C. The cyclic behavior of the weld material (WM) and cross-weld (CW) specimens are compared with previously published base material (BM) tests. The weld material is shown to give a significantly harder and stiffer stress–strain response than both the base material and the cross-weld material. The cross-weld tests exhibited a cyclic stress–strain response, which was similar to that of the base material. All specimen types exhibited cyclic softening but the degree of softening exhibited by the cross-weld specimens was lower than that of the base material and all-weld tests. Finite element models of the base metal, weld metal and cross-weld test specimens are developed and employed for identification of the cyclic viscoplasticity material parameters. Heat affected zone (HAZ) cracking was observed for the cross-weld tests.

Sign in / Sign up

Export Citation Format

Share Document