scholarly journals Solid State Imaging Techniques. An Image Pick-up Method for an HDTV High-speed CCD Camera.

1999 ◽  
Vol 53 (2) ◽  
pp. 288-294 ◽  
Author(s):  
Masayuki Sugawara ◽  
Toshinori Saitoh ◽  
Yoshihiro Fujita ◽  
Toshiya Kikkawa ◽  
Junichi Yamazaki ◽  
...  
Keyword(s):  
Solid State ◽  
High Speed ◽  
Imaging Techniques ◽  
Ccd Camera

scholarly journals Solid State Imaging Techniques. A New 3 CCD Camera System for Consumer Use.

1996 ◽  
Vol 50 (2) ◽  
pp. 266-273
Author(s):  
Takashi Sakaguchi ◽  
Takeshi Hamasaki ◽  
Takahiro Kobayashi ◽  
Akihiro Tamura ◽  
Masaaki Nakayama ◽  
...  
Keyword(s):  
Solid State ◽  
Imaging Techniques ◽  
Ccd Camera ◽  
Camera System

scholarly journals Solid State Imaging Techniques. A High-speed Image Recording System for Consumer Use.

1997 ◽  
Vol 51 (2) ◽  
pp. 248-255
Author(s):  
Masahiko Tomikawa ◽  
Hidefumi Okada ◽  
Akio Kobayashi ◽  
Hirotsugu Murashima
Keyword(s):  
Solid State ◽  
High Speed ◽  
Imaging Techniques ◽  
Recording System ◽  
Image Recording

High-speed brightfield 3-D imaging and 3-D image analysis of thick and overlapped cell clusters in cytological preparations

1994 ◽  
Vol 52 ◽  
pp. 218-219
Author(s):  
Robert W. Mackin
Keyword(s):  
Image Analysis ◽  
High Speed ◽  
Three Dimensional ◽  
Image Data ◽  
Ccd Camera ◽  
Objective Lens ◽  
Array Processor ◽  
Vaginal Smears ◽  
Low Contrast ◽  
Computer Controlled

This paper presents two advances towards the automated three-dimensional (3-D) analysis of thick and heavily-overlapped regions in cytological preparations such as cervical/vaginal smears. First, a high speed 3-D brightfield microscope has been developed, allowing the acquisition of image data at speeds approaching 30 optical slices per second. Second, algorithms have been developed to detect and segment nuclei in spite of the extremely high image variability and low contrast typical of such regions. The analysis of such regions is inherently a 3-D problem that cannot be solved reliably with conventional 2-D imaging and image analysis methods.High-Speed 3-D imaging of the specimen is accomplished by moving the specimen axially relative to the objective lens of a standard microscope (Zeiss) at a speed of 30 steps per second, where the stepsize is adjustable from 0.2 - 5μm. The specimen is mounted on a computer-controlled, piezoelectric microstage (Burleigh PZS-100, 68/μm displacement). At each step, an optical slice is acquired using a CCD camera (SONY XC-11/71 IP, Dalsa CA-D1-0256, and CA-D2-0512 have been used) connected to a 4-node array processor system based on the Intel i860 chip.

Five-Dimensional Microscopy using Widefield-Deconvolution: Practical Considerations and Biological Applications

1996 ◽  
Vol 54 ◽  
pp. 268-269
Author(s):  
W.F. Marshall ◽  
K. Oegema ◽  
J. Nunnari ◽  
A.F. Straight ◽  
D.A. Agard ◽  
...  
Keyword(s):  
Confocal Microscopy ◽  
High Speed ◽  
Laser Scanning ◽  
Ccd Camera ◽  
Image Plane ◽  
Time Lapse ◽  
Laser Scanning Confocal Microscopy ◽  
Three Dimensions ◽  
Excitation Light ◽  
Cooled Ccd

The ability to image cells in three dimensions has brought about a revolution in biological microscopy, enabling many questions to be asked which would be inaccessible without this capability. There are currently two major methods of three dimensional microscopy: laser-scanning confocal microscopy and widefield-deconvolution microscopy. The method of widefield-deconvolution uses a cooled CCD to acquire images from a standard widefield microscope, and then computationally removes out of focus blur. Using such a scheme, it is easy to acquire time-lapse 3D images of living cells without killing them, and to do so for multiple wavelengths (using computer-controlled filter wheels). Thus, it is now not only feasible, but routine, to perform five dimensional microscopy (three spatial dimensions, plus time, plus wavelength).Widefield-deconvolution has several advantages over confocal microscopy. The two main advantages are high speed of acquisition (because there is no scanning, a single optical section is acquired at a time by using a cooled CCD camera) and the use of low excitation light levels Excitation intensity can be much lower than in a confocal microscope for three reasons: 1) longer exposures can be taken since the entire 512x512 image plane is acquired in parallel, so that dwell time is not an issue, 2) the higher quantum efficiently of a CCD detect over those typically used in confocal microscopy (although this is expected to change due to advances in confocal detector technology), and 3) because no pinhole is used to reject light, a much larger fraction of the emitted light is collected. Thus we can typically acquire images with thousands of photons per pixel using a mercury lamp, instead of a laser, for illumination. The use of low excitation light is critical for living samples, and also reduces bleaching. The high speed of widefield microscopy is also essential for time-lapse 3D microscopy, since one must acquire images quickly enough to resolve interesting events.

A Solid-State On-Load Tap Changer for the Power Transformers of 10—0.4 kV Distribution Networks

Vestnik MEI ◽  
2020 ◽  
Vol 6 (6) ◽  
pp. 82-90
Author(s):  
Dmitriy I. Panfilov ◽  
◽  
Mikhail G. Astashev ◽  
Aleksandr V. Gorchakov ◽  
◽  
...  
Keyword(s):  
Solid State ◽  
Physical Model ◽  
High Speed ◽  
Power Transformer ◽  
Voltage Control ◽  
Power Transformers ◽  
Control Algorithms ◽  
Load Voltage ◽  
Tap Changer ◽  
Load Tap Changer

The specific features relating to voltage control of power transformers at distribution network transformer substations are considered. An approach to implementing high-speed on-load voltage control of serially produced 10/0.4 kV power transformers by using a solid-state on-load tap changer (SOLTC) is presented. An example of the SOLTC circuit solution on the basis of thyristor switches is given. On-load voltage control algorithms for power transformers equipped with SOLTC that ensure high reliability and high-speed operation are proposed. The SOLTC performance and the operability of the suggested voltage control algorithms were studied by simulation in the Matlab/Simulink environment and by experiments on the SOLTC physical model. The structure and peculiarities of the used simulation Matlab model are described. The SOLTC physical model design and its parameters are presented. The results obtained from the simulating the SOLTC operation on the Matlab model and from the experiments on the SOLTS physical model jointly with a power transformer under different loads and with using different control algorithms are given. An analysis of the experimental study results has shown the soundness of the adopted technical solutions. It has been demonstrated that the use of an SOLTC ensures high-speed voltage control, high efficiency and reliability of its operation, and arcless switching of the power transformer regulating taps without load voltage and current interruption. By using the SOLTC operation algorithms it is possible to perform individual phase voltage regulation in a three-phase 0.4 kV distribution network. The possibility of integrating SOLTC control and diagnostic facilities into the structure of modern digital substations based on the digital interface according to the IEC 61850 standard is noted.

Evaluation of Package Defects by Thermal Imaging Techniques

2002 ◽  
Author(s):  
Yongmei Liu ◽  
Rajen Dias
Keyword(s):  
Infrared Thermography ◽  
Thermal Imaging ◽  
High Speed ◽  
Imaging Techniques ◽  
Thermal Response ◽  
Analysis Tool ◽  
Nondestructive Analysis ◽  
Ir Camera ◽  
External Heating

Abstract Study presented here has shown that Infrared thermography has the potential to be a nondestructive analysis tool for evaluating package sublayer defects. Thermal imaging is achieved by applying pulsed external heating to the package surface and monitoring the surface thermal response as a function of time with a high-speed IR camera. Since the thermal response of the surface is affected by the defects such as voids and delamination below the package surface, the technique can be used to assist package defects detection and analysis.

scholarly journals Rapid Foreign Object Detection System on Seaweed Using VNIR Hyperspectral Imaging

Sensors ◽  
2021 ◽  
Vol 21 (16) ◽  
pp. 5279
Author(s):  
Dong-Hoon Kwak ◽  
Guk-Jin Son ◽  
Mi-Kyung Park ◽  
Young-Duk Kim
Keyword(s):  
Object Detection ◽  
Real Time ◽  
Hyperspectral Imaging ◽  
High Speed ◽  
Detection System ◽  
Imaging Techniques ◽  
Foreign Object ◽  
Subtraction Method ◽  
Foreign Objects ◽  
Time Operation

The consumption of seaweed is increasing year by year worldwide. Therefore, the foreign object inspection of seaweed is becoming increasingly important. Seaweed is mixed with various materials such as laver and sargassum fusiforme. So it has various colors even in the same seaweed. In addition, the surface is uneven and greasy, causing diffuse reflections frequently. For these reasons, it is difficult to detect foreign objects in seaweed, so the accuracy of conventional foreign object detectors used in real manufacturing sites is less than 80%. Supporting real-time inspection should also be considered when inspecting foreign objects. Since seaweed requires mass production, rapid inspection is essential. However, hyperspectral imaging techniques are generally not suitable for high-speed inspection. In this study, we overcome this limitation by using dimensionality reduction and using simplified operations. For accuracy improvement, the proposed algorithm is carried out in 2 stages. Firstly, the subtraction method is used to clearly distinguish seaweed and conveyor belts, and also detect some relatively easy to detect foreign objects. Secondly, a standardization inspection is performed based on the result of the subtraction method. During this process, the proposed scheme adopts simplified and burdenless calculations such as subtraction, division, and one-by-one matching, which achieves both accuracy and low latency performance. In the experiment to evaluate the performance, 60 normal seaweeds and 60 seaweeds containing foreign objects were used, and the accuracy of the proposed algorithm is 95%. Finally, by implementing the proposed algorithm as a foreign object detection platform, it was confirmed that real-time operation in rapid inspection was possible, and the possibility of deployment in real manufacturing sites was confirmed.

High Speed Imaging Techniques For Pulse Nuclear Radiation Source

1989 ◽  
Author(s):  
Wang Kuilu ◽  
Lu Ming ◽  
Liu Cunfu ◽  
Kang Dechun
Keyword(s):  
Radiation Source ◽  
High Speed ◽  
Imaging Techniques ◽  
Nuclear Radiation ◽  
High Speed Imaging

Towards A Multi-FPGA Infrared Simulator

2007 ◽  
Vol 4 (4) ◽  
pp. 343-355 ◽  
Author(s):  
Vinay Sriram ◽  
David Kearney
Keyword(s):  
Homeland Security ◽  
Reconfigurable Computing ◽  
High Speed ◽  
High Performance ◽  
Large Scale ◽  
Computation Time ◽  
Ccd Camera ◽  
Hardware Acceleration ◽  
Limiting Factor ◽  
Scene Simulation

High speed infrared (IR) scene simulation is used extensively in defense and homeland security to test sensitivity of IR cameras and accuracy of IR threat detection and tracking algorithms used commonly in IR missile approach warning systems (MAWS). A typical MAWS requires an input scene rate of over 100 scenes/second. Infrared scene simulations typically take 32 minutes to simulate a single IR scene that accounts for effects of atmospheric turbulence, refraction, optical blurring and charge-coupled device (CCD) camera electronic noise on a Pentium 4 (2.8GHz) dual core processor [7]. Thus, in IR scene simulation, the processing power of modern computers is a limiting factor. In this paper we report our research to accelerate IR scene simulation using high performance reconfigurable computing. We constructed a multi Field Programmable Gate Array (FPGA) hardware acceleration platform and accelerated a key computationally intensive IR algorithm over the hardware acceleration platform. We were successful in reducing the computation time of IR scene simulation by over 36%. This research acts as a unique case study for accelerating large scale defense simulations using a high performance multi-FPGA reconfigurable computer.

Sign in / Sign up

Export Citation Format

Share Document