scholarly journals Measurements of Flow Field within the Rotating Blade Row Using a Laser Two Focus Velocimeter

1984 ◽  
Vol 4 (Supplement) ◽  
pp. 141-144
Author(s):  
Shohachi YASU
Keyword(s):  
Flow Field ◽  
Rotating Blade ◽  
Blade Row

Experimental Study of an Axial Compressor Rotor Transfer Function With Non-Uniform Inlet Flow

1978 ◽  
Author(s):  
J. Colpin ◽  
P. Kool
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Hot Wire ◽  
Flow Angle ◽  
Compressor Rotor ◽  
Rotating Blade ◽  
Absolute Flow ◽  
Blade Row ◽  
Upstream Flow

The aim of the investigation is to study the propagation of a non-uniform upstream flow field through a rotating blade row. The flow is investigated using classical pneumatic instrumentation and hot wire anemometry. The latter allows one to determine the average flow values as well as the instantaneous blade-to-blade flow field. These measurements were performed upstream and downstream of a low-speed axial compressor stage rotor. A triangular inlet total pressure distortion was generated with a grid system, movable in the circumferential direction. The hot-wire data were processed with a periodic sampling and averaging technique to obtain the three-dimensional blade-to-blade flow downstream of the rotor at mid-span. The modification of the blade wakes and the existence of large absolute flow angle fluctuations are evidenced for different relative positions of the distortion and stationary hot wire.

Evaluation of a Flow Measurement Probe Influence on the Flow Field in High Speed Axial Compressors

2021 ◽  
Author(s):  
Ryosuke Seki ◽  
Satoshi Yamashita ◽  
Ryosuke Mito
Keyword(s):  
Flow Field ◽  
Approximation Method ◽  
High Speed ◽  
Static Pressure ◽  
Axial Compressor ◽  
Pressure Change ◽  
Operating Point ◽  
Blade Row ◽  
Probe Insertion ◽  
Probe Geometry

Abstract The aerodynamic effects of a probe for stage performance evaluation in a high-speed axial compressor are investigated. Regarding the probe measurement accuracy and its aerodynamic effects, the upstream/downstream effects on the probe and probe insertion effects are studied by using an unsteady computational fluid dynamics (CFD) analysis and by verifying in two types of multistage high-speed axial compressor measurements. The probe traverse measurements were conducted at the stator inlet and outlet in each case to evaluate blade row performance quantitatively and its flow field. In the past study, the simple approximation method was carried out which considered only the interference of the probe effect based on the reduction of the mass flow by the probe blockage for the compressor performance, but it did not agree well with the measured results. In order to correctly and quantitatively grasp the mechanism of the flow field when the probe is inserted, the unsteady calculation including the probe geometry was carried out in the present study. Unsteady calculation was performed with a probe inserted completely between the rotor and stator of a 4-stage axial compressor. Since the probe blockage and potential flow field, which mean the pressure change region induced by the probe, change the operating point of the upstream rotor and increase the work of the rotor. Compared the measurement result with probe to a kiel probe setting in the stator leading edge, the total pressure was increased about 2,000Pa at the probe tip. In addition, the developed wake by the probe interferes with the downstream stator row and locally changes the static pressure at the stator exit. To evaluate the probe insertion effect, unsteady calculations with probe at three different immersion heights at the stator downstream in an 8-stage axial compressor are performed. The static pressure value of the probe tip was increased about 3,000Pa in the hub region compared to tip region, this increase corresponds to the measurement trend. On the other hand, the measured wall static pressure showed that there is no drastic change in the radial direction. In addition, when the probe is inserted from the tip to hub region in the measurement, the blockage induced by the probe was increased. As a result, operating point of the stator was locally changed, and the rise of static pressure of the stator increased when the stator incidence changed. These typical results show that unsteady simulations including probe geometry can accurately evaluate the aerodynamic effects of probes in the high-speed axial compressor. Therefore, since the probe will pinpointed and strong affects the practically local flow field in all rotor upstream passage and stator downstream, as for the probe measurement, it is important to pay attention to design the probe diameter, the distance from the blade row, and its relative position to the downstream stator. From the above investigations, a newly simple approximation method which includes the effect of the pressure change evaluation by the probe is proposed, and it is verified in the 4-stage compressor case as an example. In this method, the effects of the distance between the rotor trailing edge (T.E.) and the probe are considered by the theory of the incompressible two-dimensional potential flow. The probe blockage decreases the mass flow rate and changes the operating point of the compressor. The verification results conducted in real compressor indicate that the correct blockage approximation enables designer to estimate aerodynamic effects of the probe correctly.

Unsteady Flow Analysis and Vibratory Stress Predictions for a High Work Single Stage Turbine Blade

2012 ◽  
Author(s):  
Kurt Weber ◽  
Girish Modgil ◽  
Steve Gegg ◽  
Shyam Neerarambam ◽  
Moujin Zhang
Keyword(s):  
Flow Field ◽  
Strain Gauge ◽  
Flow Analysis ◽  
Forced Response ◽  
Single Stage ◽  
Turbine Stage ◽  
Rotating Blade ◽  
Gauge Data ◽  
Unsteady Flow Analysis ◽  
High Work

The flow field in High-Work Single-Stage (HWSS) turbines differs from traditional turbine flow fields. Operating at increased pressure ratios, wakes and trailing edge shocks at the exit of the vane are more likely to cause a vibratory response in the rotating blade. This flow field can produce increased excitation at harmonics that correspond to the vane passing frequency and harmonics higher than the vane passing frequency. In this paper, blade vibratory stresses in a HWSS gas turbine stage are predicted using unsteady pressures from two Rolls-Royce in-house flow codes that employ different phase lagged unsteady approaches. Hydra uses a harmonic storage approach, and the Vane/Blade Interaction (VBI) code uses a direct storage approach. Harmonic storage reduces memory requirements considerably. The predicted stress for four modes at two engine speeds are presented and are compared with rig test strain gauge data to assess and validate the predictive capability of the codes for forced response. Strain gauge data showed the need to consider harmonics higher than the fundamental vane passing frequency for the max power shaft speed and operating at the conditions. Because of this, it was a good case for validation and for comparing the two codes. Overall, it was found that, stress predictions using the Hydra flow code compare better with data. To the best of the authors’ knowledge, this paper is a first in comparing two different phase lagged unsteady approaches, in the context of forced response, to engine rig data for a High-Work Single Stage turbine.

Blade-Row Interactions in an LP Turbine at Design and Strong Off-Design Operation

2014 ◽  
Author(s):  
Martin Lipfert ◽  
Jan Habermann ◽  
Martin G. Rose ◽  
Stephan Staudacher ◽  
Yavuz Guendogdu
Keyword(s):  
Experimental Data ◽  
Flow Field ◽  
Three Dimensional ◽  
Suction Side ◽  
Test Facility ◽  
Time Resolved ◽  
Joint Project ◽  
Multi Stage ◽  
Blade Row ◽  
Wake Interactions

In a joint project between the Institute of Aircraft Propulsion Systems (ILA) and MTU Aero Engines a two-stage low pressure turbine is tested at design and strong off-design conditions. The experimental data taken in the altitude test-facility aims to study the effect of positive and negative incidence of the second stator vane. A detailed insight and understanding of the blade row interactions at these regimes is sought. Steady and time-resolved pressure measurements on the airfoil as well as inlet and outlet hot-film traverses at identical Reynolds number are performed for the midspan streamline. The results are compared with unsteady multi-stage CFD predictions. Simulations agree well with the experimental data and allow detailed insights in the time-resolved flow-field. Airfoil pressure field responses are found to increase with positve incidence whereas at negative incidence the magnitude remains unchanged. Different pressure to suction side phasing is observed for the studied regimes. The assessment of unsteady blade forces reveals that changes in unsteady lift are minor compared to changes in axial force components. These increase with increasing positive incidence. The wake-interactions are predominating the blade responses in all regimes. For the positive incidence conditions vane 1 passage vortex fluid is involved in the midspan passage interaction leading to a more distorted three-dimensional flow field.

Low Pressure Turbine Lapse Rate Study: CFD Model vs. Rig Data

2002 ◽  
Author(s):  
J.-S. Liu ◽  
M. L. Celestina ◽  
G. B. Heitland ◽  
D. B. Bush ◽  
M. L. Mansour ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Fluid Dynamic ◽  
Low Reynolds Number ◽  
Low Pressure ◽  
Lapse Rate ◽  
Bypass Transition ◽  
Blade Row ◽  
Low Reynolds ◽  
Lp Turbine

As an aircraft engine operates from sea level take-off (SLTO) to altitude cruise, the low pressure (LP) turbine Reynolds number decreases. As Reynolds number is reduced the condition of the airfoil boundary layer shifts from bypass transition to separated flow transition. This can result in a significant loss. The LP turbine performance fall-off from SLTO to altitude cruise, due to the loss increase with reduction in Reynolds number, is referred to as a lapse rate. A considerable amount of research in recent years has been focused on understanding and reducing the loss associated with the low Reynolds number operation. A recent 3-1/2 stage LP turbine design completed a component rig test program at Honeywell. The turbine rig test included Reynolds number variation from SLTO to altitude cruise conditions. While the rig test provides detailed inlet and exit condition measurements, the individual blade row effects are not available. Multi-blade row computational fluid dynamics (CFD) analysis is used to complement the rig data by providing detailed flow field information through each blade row. A multi-blade row APNASA model was developed and solutions were obtained at the SLTO and altitude cruise rig conditions. The APNASA model predicts the SLTO to altitude lapse rate within 0.2 point compared to the rig data. The global agreement verifies the modeling approach and provides a high confidence level in the blade row flow field predictions. Additional Reynolds number investigation with APNASA will provide guidance in the LP turbine Reynolds number research areas to reduce lapse rate. To accurately predict the low Reynolds number flow in the LP turbine is a challenging task for any computational fluid dynamic (CFD) code. The purpose of this study is to evaluate the capability of a CFD code, APNASA, to predict the sensitivity of the Reynolds number in LP turbines.

Effects of Off-Design Operating Conditions on the Blade Row Interaction in a HP Turbine Stage

2007 ◽  
Author(s):  
G. Persico ◽  
P. Gaetani ◽  
C. Osnaghi
Keyword(s):  
Flow Field ◽  
Strong Dependence ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Pressure Probe ◽  
Turbine Stage ◽  
Mixing Rate ◽  
Aerodynamic Pressure ◽  
Blade Row ◽  
Blade Row Interaction

An extensive experimental analysis on the subject of the unsteady periodic flow in a highly subsonic HP turbine stage has been carried out at the Laboratorio di Fluidodinamica delle Macchine (LFM) of the Politecnico di Milano (Italy). In this paper the blade row interaction is progressively enforced by increasing the stator and rotor blade loading and by reducing the stator-rotor axial gap from 100% (very large to smooth the rotor inlet unsteadiness) to 35% (design configuration) of the stator axial chord. The time-averaged three-dimensional flow field in the stator-rotor gap was investigated by means of a conventional five-hole probe for the nominal (0°) and an highly positive (+22°) stator incidences. The evolution of the viscous flow structures downstream of the stator is presented to characterize the rotor incoming flow. The blade row interaction was evaluated on the basis of unsteady aerodynamic measurements at the rotor exit, performed with a fast-response aerodynamic pressure probe. Results show a strong dependence of the time-averaged and phase-resolved flow field and of the stage performance on the stator incidence. The structure of the vortex-blade interaction changes significantly as the magnitude of the rotor inlet vortices increases, and very different residual traces of the stator secondary flows are found downstream of the rotor. On the contrary, the increase of rotor loading enhances the unsteadiness in the rotor secondary flows but has a little effect on the vortex-vortex interaction. For the large axial gap, a reduction of stator-related effects at the rotor exit is encountered when the stator incidence is increased as a result of the different mixing rate within the cascade gap.

scholarly journals Aerodynamic Detuning Analysis of an Unstalled Supersonic Turbofan Cascade

1986 ◽  
Vol 108 (1) ◽  
pp. 60-67 ◽  
Author(s):  
D. Hoyniak ◽  
S. Fleeter
Keyword(s):  
Flow Field ◽  
Leading Edge ◽  
Rotor Blades ◽  
Driving Mechanism ◽  
Aeroelastic Stability ◽  
Aerodynamic Forces ◽  
Unsteady Aerodynamic ◽  
Influence Coefficients ◽  
Blade Row ◽  
The Stability

A new, and as yet unexplored, approach to passive flutter control is aerodynamic detuning, defined as designed passage-to-passage differences in the unsteady aerodynamic flow field of a rotor blade row. Thus, aerodynamic detuning directly affects the fundamental driving mechanism for flutter, i.e., the unsteady aerodynamic forces and moments acting on individual rotor blades. In this paper, a model to demonstrate the enhanced supersonic unstalled aeroelastic stability associated with aerodynamic detuning is developed. The stability of an aerodynamically detuned cascade operating in a supersonic inlet flow field with a subsonic leading edge locus is analyzed, with the aerodynamic detuning accomplished by means of nonuniform circumferential spacing of adjacent rotor blades. The unsteady aerodynamic forces and moments on the blading are defined in terms of influence coefficients in a manner that permits the stability of both a conventional uniformly spaced rotor configuration as well as the detuned nonuniform circumferentially spaced rotor to be determined. With Verdon’s uniformly spaced Cascade B as a baseline, this analysis is then utilized to demonstrate the potential enhanced aeroelastic stability associated with this particular type of aerodynamic detuning.

Periodical Unsteady Flow Within a Rotor Blade Row of an Axial Compressor: Part II — Wake–Tip Clearance Vortex Interaction

2007 ◽  
Author(s):  
Ronald Mailach ◽  
Ingolf Lehmann ◽  
Konrad Vogeler
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Rotor Blade ◽  
Pressure Sensors ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Lower Velocity ◽  
Blade Row ◽  
Blade Tip ◽  
Tip Clearance Vortex

In this two-part paper results of the periodical unsteady flow field within the third rotor blade row of the four-stage Dresden Low-Speed Research Compressor are presented. The main part of the experimental investigations was performed using Laser-Doppler-Anemometry. Results of the flow field at several spanwise positions between midspan and rotor blade tip will be discussed. In addition time-resolving pressure sensors at midspan of the rotor blades provide information about the unsteady profile pressure distribution. In part II of the paper the flow field in the rotor blade tip region will be discussed. The experimental results reveal a strong periodical interaction of the incoming stator wakes and the rotor blade tip clearance vortices. Consequently, in the rotor frame of reference the tip clearance vortices are periodical with the stator blade passing frequency. Due to the wakes the tip clearance vortices are separated into different segments. Along the mean vortex trajectory these parts can be characterised by alternating patches of higher and lower velocity and flow turning or subsequent counterrotating vortex pairs. These flow patterns move downstream along the tip clearance vortex path in time. As a result of the wake influence the orientation and extension of the tip clearance vortices as well as the flow blockage periodically vary in time.

Sign in / Sign up

Export Citation Format

Share Document