scholarly journals Adhesion properties of styrene-butadiene rubber (SBR)/Standard Malaysian Rubber (SMR L)-based adhesives in the presence of phenol formaldehyde resin

2007 ◽  
Vol 1 (10) ◽  
pp. 654-659 ◽  
Author(s):  
B. T. Poh ◽  
L. N. Ong
Keyword(s):  
Phenol Formaldehyde ◽  
Phenol Formaldehyde Resin ◽  
Styrene Butadiene Rubber ◽  
Formaldehyde Resin ◽  
Butadiene Rubber ◽  
Adhesion Properties ◽  
Styrene Butadiene

scholarly journals Self-adhesion X-ray Shielding Composite Material of EPDM Rubber with Barite: Mechanical Properties

2020 ◽  
Vol 57 (1) ◽  
pp. 28-36
Author(s):  
Vasiliy Cherkasov ◽  
Yuiy Yurkin ◽  
Valeriy Avdonin ◽  
Dmitriy Suntsov
Keyword(s):  
Mechanical Properties ◽  
Phenol Formaldehyde ◽  
Peel Strength ◽  
Phenol Formaldehyde Resin ◽  
Formaldehyde Resin ◽  
Adhesion Properties ◽  
X Ray ◽  
Industrial Oil ◽  
Oil Concentration ◽  
Free Material

It is actual now to work out new radiation protecting sheeting on the basis of non-curing polymeric composition which possess self-adhesion properties, are easily mounted and dismantled and provide high tightness and low permeability. Mechanical properties of non-curing composites consisting of ethylene propylene diene monomer (EPDM), industrial oil (IO), alkyl phenol-formaldehyde resin (PF) with addition of barite (52 %) to the total material volume were investigated in this article. The aim of investigation is to find optimal content of the above mentioned components at which it would be possible to get the following properties: composite would be sticky enough (peel strength not less than 4 N/cm); character of a separation would be cohesive (on a material) and thus there would be no migration of softener and satisfactory resistance of fluidity. The results showed that PF addition till 20 % in the system EPDM/PF leads to the increasing of adhesive strength, in this case optimal oil concentration in the system EPDM/PF/IO is in the interval from 45 till 55 %. New self-adhesion lead-free material, exhibited higher X-ray-shielding properties, is also received in the result of investigation.

Oil and Petrol Resistant Thermoplastic Vulcanizations Based on ABS-Plastic Mixture with Copolymer Butadiene and Acrylonitrile

2019 ◽  
Vol 816 ◽  
pp. 192-196
Author(s):  
Alsou D. Nasertdinova ◽  
A.D. Dementev ◽  
A.D. Khusainov ◽  
Svetoslav Isaakovich Volfson
Keyword(s):  
Mechanical Properties ◽  
Phenol Formaldehyde ◽  
Strength Properties ◽  
Phenol Formaldehyde Resin ◽  
Formaldehyde Resin ◽  
Butadiene Rubber ◽  
Dynamic Vulcanization ◽  
Alkyl Phenol ◽  
Rubber Compounds ◽  
Thermoplastic Vulcanizates

The effect of the type and dosage of sulfur and resin (alkyl phenol formaldehyde resin grade SP - 1045) vulcanizing systems on the oil and petrol resistance and elastic strength properties of thermoplastic vulcanizates (TPV) obtained on the basis of nitrile-butadiene rubber and ABS-plastic, with a ratio of 70/30 respectively has been studied. In the course of studies of vulcanization characteristics, it was found that with an increase in the content of the vulcanizing system, the rate of vulcanization increases both during the vulcanization of rubber compounds and during dynamic vulcanization. The physic-mechanical properties of the TPV obtained indicate that with a fascination for the content of the vulcanizing system, the elastic-strength properties and the oil and petrol resistance of the TPV are also increased.

Effects of White Rot Fungus Physisporinus sp., Isolated in Japan, on Styrene-butadiene Rubber

2020 ◽  
Vol 93 (9) ◽  
pp. 289-292
Author(s):  
Yumi SHIMIZU ◽  
Shuma SATHO ◽  
Taro NAKAJIMA ◽  
Hiroaki KOUZAI ◽  
Kiminori SHIMIZU
Keyword(s):  
White Rot ◽  
White Rot Fungus ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Styrene Butadiene

Purification of water contaminated with heavy metals by example of lead as promising material based on graphene nanostructures

2020 ◽  
pp. 34-43
Author(s):  
N. R. Memetov ◽  
◽  
A. V. Gerasimova ◽  
A. E. Kucherova ◽  
◽  
...  
Keyword(s):  
Adsorption Process ◽  
Phenol Formaldehyde ◽  
Phenol Formaldehyde Resin ◽  
Formaldehyde Resin ◽  
Parameter Estimates ◽  
Maximum Adsorption Capacity ◽  
Ecological Situation ◽  
Characteristic Parameters ◽  
Purification Of Water ◽  
Graphene Nanostructures

The paper evaluates the effectiveness of the use of graphene nanostructures in the purification of lead (II) ions to improve the ecological situation of water bodies. The mechanisms and characteristic parameters of the adsorption process were analyzed using empirical models of isotherms at temperatures of 298, 303, 313 and 323 K, which correspond to the following order (based on the correlation coefficient): Langmuir (0.99) > Temkin (0.97) > Dubinin – Radushkevich (0.90). The maximum adsorption capacity of the material corresponds to the range from 230 to 260 mg/g. We research the equilibrium at the level of thermodynamic parameter estimates, which indicates the spontaneity of the process, the endothermic nature and structure change of graphene modified with phenol-formaldehyde resin during the adsorption of lead (II) ions, leading to an increase in the disorder of the system.

Sign in / Sign up

Export Citation Format

Share Document