Evaluation of Adhesion Properties of Modified Asphalt Binders with Use of Binder Bond Strength Test

2017 ◽  
Vol 2632 (1) ◽  
pp. 88-98 ◽  
Author(s):  
Weidong Huang ◽  
Lu Zhou
Keyword(s):  
Bond Strength ◽  
Asphalt Binder ◽  
Gel Permeation Chromatography ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Adhesion Properties ◽  
Rubber Powder ◽  
Positive Effects ◽  
Tracking Device ◽  
Styrene Butadiene

Moisture damage is a prominent problem of asphalt pavements. The bond strength between asphalt and aggregates is a crucial factor that influences the capability of asphalt to resist moisture-induced damage. In this study, a binder bond strength (BBS) test was conducted to evaluate the effects of various modifiers and additives of different amounts on bond strength between asphalt and aggregates. Furthermore, the influence of styrene–butadiene–styrene (SBS) on adhesion behavior of asphalt binder was investigated through a gel permeation chromatography (GPC) test. Finally, the results of the BBS test were compared with the findings obtained from a Hamburg wheel-tracking device (HWTD) test, which reflected the moisture sensitivity of mixtures under wet conditions. Results indicated that gilsonite, high-density polyethylene, and polyphosphoric acid improved the bond strength of the base asphalt; SBS had no positive effects on asphalt adhesion properties; and SBS at a low amount reduced the bond strength. Ethylene bis-stearamide wax, crumb rubber, terminal blend (TB) rubber powder, and compound modifier TB rubber powder plus SBS decreased the bond strength. The GPC test results showed that SBS possibly did not actively contribute to the formation of bond strength between asphalt and aggregates. Test data for BBS and HWTD tests under wet conditions confirmed that there was no discernible correlation between these two tests when adhesion properties of modified asphalts were evaluated. However, the results of the BBS test were in accordance with those of the HWTD test when the adhesion of asphalt with different amounts of the same modifier and the mixture resistance to water damage were evaluated.

scholarly journals Material Properties and Environmental Benefits of Hot-Mix Asphalt Mixes Including Local Crumb Rubber Obtained from Scrap Tires

Environments ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 47
Author(s):  
Lim Min Khiong ◽  
Md. Safiuddin ◽  
Mohammad Abdul Mannan ◽  
Resdiansyah
Keyword(s):  
Asphalt Binder ◽  
Crumb Rubber ◽  
Environmental Benefits ◽  
Asphalt Binders ◽  
Rubber Content ◽  
Scrap Tires ◽  
Asphalt Mixes ◽  
Temperature Resistance ◽  
Modified Asphalt ◽  
Marshall Stability

This paper presents the results of a laboratory-based experimental investigation on the properties of asphalt binder and hot-mix asphalt (HMA) mixes modified by locally available crumb rubber, which was used as a partial replacement of asphalt by weight. In this study, fine crumb rubber with a particle size in the range of 0.3–0.6 mm, obtained from scrap tires, was added to the asphalt binder through the wet process. Crumb rubber contents of 5%, 10%, 15%, and 19% by weight of asphalt were added to the virgin binder in order to prepare the modified asphalt binder samples, while the unmodified asphalt binder was used as the control sample. The crumb rubber modified binder samples were examined for measuring viscosity indirectly using the penetration test, and temperature resistance using the softening point test. Later, both the modified and unmodified asphalt binders were used to produce HMA mixes. Two categories of HMA mix commonly used in Malaysia—namely, AC 14 (dense-graded) and SMA 14 (gap-graded)—were produced using the modified asphalt binders containing 5%, 10%, 15%, and 19% crumb rubber. Two AC 14 and SMA 14 control mixes were also produced, incorporating the unmodified asphalt binder (0% crumb rubber). All of the AC 14 and SMA 14 asphalt mixes were examined in order to determine their volumetric properties, such as bulk density, voids in total mix (VTM), voids in mineral aggregate (VMA), and voids filled with asphalt (VFA). In addition, the Marshall stability, Marshall flow, and stiffness of all of the AC 14 and SMA 14 mixes were determined. Test results indicated that the modified asphalt binders possessed higher viscosity and temperature resistance than the unmodified asphalt binder. The viscosity and temperature resistance of the asphalt binders increased with the increase in their crumb rubber content. The increased crumb rubber content also led to improvements in the volumetric properties (bulk density, VTM, VMA, and VFA) of the AC 14 and SMA 14 mixes. In addition, the performance characteristics of the AC 14 and SMA 14 mixes—such as Marshall stability, Marshall flow, and stiffness—increased with the increase in crumb rubber content. However, the AC 14 mixes performed much better than the SMA 14 mixes. The overall research findings suggest that crumb rubber can be used to produce durable and sustainable HMA mixes, with manifold environmental benefits, for use in flexible pavements carrying the heavy traffic load of highways.

Viscoelastic fatigue resistance of asphalt binders modified with crumb rubber and styrene butadiene polymer

2016 ◽  
Vol 35 (1) ◽  
pp. 30-36 ◽  
Author(s):  
Mahmoud Ameri ◽  
Mohammad Reza Seif ◽  
Massoumeh Abbasi ◽  
Alireza Khavandi Khiavi
Keyword(s):  
Fatigue Resistance ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Styrene Butadiene

scholarly journals Balancing the Performance and Environmental Concerns of Used Motor Oil as Rejuvenator in Asphalt Mixes

Recycling ◽  
2019 ◽  
Vol 4 (1) ◽  
pp. 11 ◽  
Author(s):  
Eslam Deef-Allah ◽  
Magdy Abdelrahman ◽  
Mark Fitch ◽  
Mohyeldin Ragab ◽  
Mousumi Bose ◽  
...  
Keyword(s):  
Environmental Protection Agency ◽  
Asphalt Binder ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Environmental Concerns ◽  
Ethyl Benzene ◽  
Motor Oil ◽  
Asphalt Mixes ◽  
Used Motor Oil ◽  
The Us

Road deterioration inspires researchers to enhance the properties of asphalt binder for better performing mixes. Recycled tire rubber, or crumb rubber modifier (CRM), and used motor oil (UMO) are two modifiers that enhance asphalt binder performance through two different mechanisms. CRM affects high-temperature properties while UMO modifies low-temperature properties. Potential environmental concerns arising from the use of UMO have been raised in the literature. In this paper, the two recycled materials were investigated for their ability to complement each other. Both performance benefits of using both materials and the environmental concerns of using UMO were studied. Four CRM asphalt binders were investigated: two with UMO and two without UMO. Environmental impacts were evaluated using gas chromatography to check air emissions for benzene, toluene, ethyl-benzene, and xylenes (BTEX). The potential for toxic leaching of elements from modified hot mix asphalt (HMA) were checked using the US Environmental Protection Agency (EPA) Toxicity Characteristic Leaching Protocol (TCLP). For asphalt binders modified by CRM-UMO combinations, CRM decreased the amounts of released BTEX components, presumably by absorbing UMO and slowing the release of BTEX. Leaching results concluded that UMO mixtures showed a notable percentage of sulfur (S) as compared to non-UMO mixes. All these leachate components were under EPA limits.

scholarly journals Experimental Study to Determine the Most Preferred Additive for Improving Asphalt Performance Using Polypropylene, Crumb Rubber, and Tafpack Super in Medium and High-Temperature Range

2019 ◽  
Vol 9 (8) ◽  
pp. 1567 ◽  
Author(s):  
Huang Xiaoming ◽  
Ismail Bakheit Eldouma
Keyword(s):  
High Temperature ◽  
Physical Properties ◽  
Mechanical Performance ◽  
Asphalt Binder ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Modified Bitumen ◽  
Asphalt Modification ◽  
Rotational Viscosity ◽  
Asphalt Performance

The overall objectives of this study were to determine the most appropriate additive for improving the physical properties and the medium- and high-temperature performances (mechanical performance) of asphalt binders. Three different types of modified binders were prepared: crumb rubber modifier (CRM), polypropylene (PP), and tafpack super (TPS), which had concentrations of 2%, 3%, 3.5%, and 4% by weight of asphalt binder, for each modifier. Their physical and rheological properties were evaluated by applying various tests such as ductility, rotational viscosity, toughness, and tenacity, as well as the dynamic shear rheometer (DSR) test. As a result, the physical properties of the modified bitumen binders were compared, as were the medium- and high-temperature performances (mechanical performance), which had temperatures of 58, 64, 70, 76, 82, and 88 °C, respectively. This was how the most appropriate modifier was determined. The results demonstrated that the asphalt binder properties significantly improved by utilizing CRM followed by PP and TPS modifiers. The increase in the rutting parameter (G*/sin(δ)) after asphalt modification indicated its excellent performance at both medium- and high-temperatures. Lastly, the CRM was determined as the most preferred additive because of its positive effect on the physical properties and enhancement of the medium- and high-temperature performance (mechanical performance).

scholarly journals Performance Evaluation of Crumb Rubber Asphalt Modified with Silicone-Based Warm Mix Additives

2020 ◽  
Vol 2020 ◽  
pp. 1-17 ◽  
Author(s):  
Nonde Lushinga ◽  
Liping Cao ◽  
Zejiao Dong ◽  
Chen Yang ◽  
Cyriaque O. Assogba
Keyword(s):  
Asphalt Binder ◽  
Fatigue Cracking ◽  
Crumb Rubber ◽  
Warm Mix Asphalt ◽  
Asphalt Binders ◽  
Water Repellent ◽  
Creep Recovery ◽  
Viscoelastic Continuum Damage ◽  
Warm Mix Additives ◽  
Different Temperatures

This research was conducted to elucidate better understanding of the performance of crumb rubber asphalt modified with silicone-based warm mix additives. Two different silicone-based warm mix asphalt (WMA) additives (herein Tego XP and Addibit) were used to prepare crumb rubber modified (CRM) warm mix asphalt binders. The viscosity of these CRM binders was measured at different temperatures and shearing rates. Furthermore, softening point and penetration tests, Multiple Stress Creep Recovery (MSCR), Time Sweep (TS), Atomic Force Microscopy (AFM), Frequency sweep (FS), and Fourier Transform Infrared (FTIR) tests were also conducted on prepared samples. Based on these robust and rigorous laboratory experiments, it was established that viscosity of CRM binders was reduced by addition of Tego XP and Addibit WMA additives. However, WMA additives had different influence on rheological properties of the binder. CRM binder with Tego XP improved resistance to rutting of the binders but would degrade the fatigue performance. On the contrary, viscoelastic continuum damage (VECD) model results and those of phase angle approach revealed that the binder with Addibit improved resistance to fatigue cracking of the binders but had no adverse effects on high temperature rutting performance. FTIR test results established a presence of polydimethylsiloxane (PDMS) in CRM binders with Tego XP and Addibit. PDMS is a well-known hydrophobic organic and inorganic polymer that is water repellent; therefore, binders containing these silicone-based warm mix additives could be beneficial in resisting moisture damage in asphalt binders and mixtures. Morphology of CRM binders with and without WMA revealed good distribution of the rubber particles in asphalt binder matrix. Further addition of WMA increased surface roughness of the binder, which can be correlated to changes in microstructure properties of the binder. Therefore, the study concluded that addition of Tego XP and Addibit reduces viscosity and improves mechanical properties of the asphalt binder.

Highly Modified Asphalt Binder for Asphalt Crack Relief Mix

2017 ◽  
Vol 2630 (1) ◽  
pp. 110-117 ◽  
Author(s):  
Matheus S. Gaspar ◽  
Kamilla L. Vasconcelos ◽  
Amanda H. M. da Silva ◽  
Liedi L. B. Bernucci
Keyword(s):  
Hot Mix Asphalt ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Bending Test ◽  
Asphalt Binders ◽  
Reflective Cracking ◽  
Modified Asphalt ◽  
Asphalt Overlay ◽  
Modified Asphalt Binder ◽  
Styrene Butadiene

Reflective cracking is a common issue with respect to rehabilitated asphalt pavements, especially when the rehabilitation is done by applying a hot-mix asphalt overlay on the existing damaged pavement. Several approaches can be adopted to delay reflective cracking. They include an increase of the overlay thickness and the use of a stress relief asphalt mixture (SRAM), which is a fine-graded, flexible, and thin asphalt interlayer. Because the efficiency of a SRAM is highly related to the properties of the asphalt binder used in the mixture, it is of interest to use a highly modified asphalt (HiMA) binder. This paper describes a field test comprising three sections at BR-116 (a heavily trafficked highway in Brazil). One of the rehabilitation strategies used for a cracked asphalt pavement was a 2.5-cm SRAM (produced with a HiMA binder) and 5-cm styrene–butadiene–styrene (SBS) hot-mix asphalt (HMA). The other two strategies were to apply SBS HMA overlays of different thicknesses (7.5 cm and 10.5 cm). The aim was to evaluate and compare the capability of these solutions to control reflective cracking. Rheological properties and multiple stress creep and recovery tests were performed on the asphalt binders, and the semicircular bending test was performed on the asphalt mixtures. The surface conditions were monitored, and the results for each section were compared. After a 29-month period, the section that received the interlayer had the lowest cracked area and showed better resistance than the overlays did to reflective cracking and better maintenance of the original thickness of the pavement.

Nonlinear Viscoelastic Response of Crumb Rubber Modified Asphalt Binder Under Large Strains

2020 ◽  
Vol 2674 (3) ◽  
pp. 139-149
Author(s):  
Saqib Gulzar ◽  
B. Shane Underwood
Keyword(s):  
Asphalt Binder ◽  
Crumb Rubber ◽  
Oscillatory Shear ◽  
Asphalt Binders ◽  
Large Strains ◽  
Viscoelastic Response ◽  
Modified Asphalt ◽  
Nonlinear Viscoelastic ◽  
Modified Asphalt Binder ◽  
Polymer Modified Asphalt

Agencies have been increasing their use of polymer modified asphalt binders in recent years to address performance issues and lengthen the useful life of their pavements. When deployed these materials likely experience strain levels exceeding their linear viscoelastic (LVE) limits. The same situation exists in non-polymer modified asphalt binders as well, but the effect may be more pronounced in polymer modified systems because of their bi-phasic nature. In this study, terminally blended crumb rubber (CR-TB) modified asphalt is studied to understand and quantify the nonlinear viscoelastic response under large strains. The CR-TB binders are extensively used in pavements subjected to high vehicular loads and extreme climatic conditions; thereby, their response under large strains becomes more critical. The current standard characterization techniques are based on LVE response using small amplitude oscillatory shear rheology only and do not consider the behavior of binders under large strains. In this study, large amplitude oscillatory shear (LAOS) rheology is used as a framework to more thoroughly investigate the complete response of the CR-TB modified asphalt binder under large strains at 30°C, 40°C, 50°C, and 60°C and at the frequencies of 0.5, 1, and 5 Hz. The LAOS response is analyzed using Fourier-transform rheology and the orthogonal stress decomposition method involving Chebyshev polynomial representation. It is found that nonlinearity manifests greatly in this study material as strain levels increase and frequencies decrease. The relative nonlinearity increases with increasing strain amplitude and is more significant towards lower end of the tested temperature range. The CR-TB binder shows strain-stiffening/softening and shear-thinning/thickening behavior depending upon a specific temperature, strain level, and frequency.

scholarly journals Enhanced Storage Stability of Different Polymer Modified Asphalt Binders through Nano-Montmorillonite Modification

Nanomaterials ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 641 ◽  
Author(s):  
Zhibin Ren ◽  
Yongqiang Zhu ◽  
Qi Wu ◽  
Minye Zhu ◽  
Feng Guo ◽  
...  
Keyword(s):  
Storage Stability ◽  
Crumb Rubber ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Widespread Application ◽  
Remarkable Effect ◽  
Modified Asphalt ◽  
Positive Effects ◽  
Polymer Modified Asphalt ◽  
Styrene Butadiene

The storage stability concern, caused by phase separation for the density difference between polymers and asphalt fractions, has limited the widespread application of polymer modified asphalt (PMA). Therefore, this study aims to improve the storage concern of PMA by incorporating nano-montmorillonite. To this end, different nano-montmorillonites were incorporated to three PMAs modified with three typical asphalt modifiers, i.e., crumb rubber (CRM), styrene–butadiene-rubber (SBR) and styrene–butadiene-styrene (SBS). A series of laboratory tests were performed to evaluate the storage stability and rheological properties of PMA binders with nano-montmorillonite. As a consequence, the incorporation of nano-montmorillonite exhibited a remarkable effect on enhancing the storage stability of the CRM modified binder, but limited positive effects for the SBR and SBS modified binders. The layered nano-montmorillonite transformed to intercalated or exfoliated structures after interaction with asphalt fractions, providing superior storage stability. Among selected nano-montmorillonites, the pure montmorillonite with Hydroxyl organic ammonium performed the best on enhancing storage stability of PMA. This paper suggests that nano-montmorillonite is a promising modifier to alleviate the storage stability concern for asphalt with polymer modifiers.

Behavior of Carbon Nano-Tubes (CNTs) as Modifier to Resist Aging and Moisture Damage in Asphalt

2020 ◽  
Vol 10 ◽  
Author(s):  
Md Arifuzzaman ◽  
R. A. Tarefder ◽  
Muhammad Saiful Islam
Keyword(s):  
Asphalt Binder ◽  
Moisture Damage ◽  
Crumb Rubber ◽  
Outdoor Environment ◽  
Adhesion Forces ◽  
Modified Asphalt ◽  
Road Pavement ◽  
Carbon Nano Tubes ◽  
Styrene Butadiene ◽  
Sbs Modified Asphalt

Background: Moisture damage and aging take place together in asphalt binder as it is on road-pavement in service life and therefore quite difficult to overcome. Various techniques, such as crumb rubber, fibres, etc., have been applied to improve the behaviour of asphalt materials Use of nano materials was found as one of the effective techniques to develop temperature performances of asphalt binder. Methods: This study investigated moisture damage and aging of asphalt binder mixing with the carbon nano tubes (CNTs) using Atomic Force Microscopy (AFM). The base binder was primarily modified with 4% SBS polymer. Later on, CNTs were mixied in different percentages (i.e., 0.5%, 1%, and 1.5%) by weight with the 4% styrene–butadiene–styrene (SBS) modified binders. A special functionalized (-NH3) AFM probe with spring constant 3.44 N/m was utilised to complete the study. Results: The results were compared with 4% SBS modified asphalt with and without CNT addition.The adhesion forces of dry samples were found smaller as compared to wet and aged asphalt samples of with and without CNT. However, the adhesion forces of wet and aged samples with investigated percentage of CNT performed considerably better than those without CNT. Conclusion: This result clearly indicated significant improvement of asphalt to overcome moisture damage and aging owing to exposure in outdoor environment as a paving material. This study recommends any dosage (i.e., 0.5 to 1.5% by weight) of CNT with 4% SBS modified asphalt to resist moisture damage and aging in field.

Sign in / Sign up

Export Citation Format

Share Document