Calibration of Side, Tip, and Total Resistance Factors for Load and Resistance Factor Design of Drilled Shafts

2012 ◽  
Vol 2310 (1) ◽  
pp. 38-48 ◽  
Author(s):  
Murad Y. Abu-Farsakh ◽  
Xinbao Yu ◽  
Zhongjie Zhang
Keyword(s):  
Drilled Shafts ◽  
Resistance Factor ◽  
Total Resistance ◽  
Resistance Factors ◽  
Factor Design ◽  
Load And Resistance Factor

scholarly journals Load and resistance factor design of drilled shafts subjected to lateral loading at service limit state

2018 ◽  
Author(s):  
◽  
Minh Dinh Uong
Keyword(s):  
Limit State ◽  
Design Procedure ◽  
Drilled Shafts ◽  
Resistance Factor ◽  
Lateral Loading ◽  
Drilled Shaft ◽  
Resistance Factors ◽  
Service Limit State ◽  
Load And Resistance Factor ◽  
Aashto Lrfd

Since 2007, the American Association of State Highway Administration Officials (AASHTO) has made utilization of Load and Resistance Factor Design (LRFD) mandatory on all federally-funded new bridge projects (AASHTO, 2007). However, currently, there are no guidelines implementing LRFD techniques for design of drilled shaft subjected to lateral loads using reliability-based analysis. On a national level, the AASHTO LRFD Bridge Design Specifications (AASHTO, 2012) specify that a resistance factor of 1.0 be used for design of drilled shafts subjected to lateral loading at service limit state, which means reliability-based analyses for calibration of resistance factors have not been performed. Therefore, there is a need to create a LRFD procedure for drilled shafts subjected to lateral loading at service limit state that has reliability-based calibrated resistance factors applicable for future projects. The research focuses on the reliability-based analysis of drilled shaft subjected to lateral loading, characterize lateral load transfer model of drilled shafts in shale, probabilistic calibrate resistance factor and contribute to the development of design procedure using LRFD. The objective of this work is to improve the design of drilled shaft subjected to lateral loading using LRFD at service limit state by providing a more reliable design procedure than the current AASHTO LRFD procedure for drilled shafts subjected to lateral loading at service limit state.

Calibration concepts for load and resistance factor design (LRFD) of reinforced soil walls

2008 ◽  
Vol 45 (10) ◽  
pp. 1377-1392 ◽  
Author(s):  
Richard J. Bathurst ◽  
Tony M. Allen ◽  
Andrzej S. Nowak
Keyword(s):  
Limit State ◽  
Reinforced Soil ◽  
Resistance Factor ◽  
Resistance Factors ◽  
Soil Walls ◽  
Calibration Methods ◽  
Load And Resistance Factors ◽  
Factor Design ◽  
Load And Resistance Factor ◽  
Reinforced Soil Walls

Reliability-based design concepts and their application to load and resistance factor design (LRFD or limit states design (LSD) in Canada) are well known, and their adoption in geotechnical engineering design is now recommended for many soil–structure interaction problems. Two important challenges for acceptance of LRFD for the design of reinforced soil walls are (i) a proper understanding of the calibration methods used to arrive at load and resistance factors, and (ii) the proper interpretation of the data required to carry out this process. This paper presents LRFD calibration principles and traces the steps required to arrive at load and resistance factors using closed-form solutions for one typical limit state, namely pullout of steel reinforcement elements in the anchorage zone of a reinforced soil wall. A unique feature of this paper is that measured load and resistance values from a database of case histories are used to develop the statistical parameters in the examples. The paper also addresses issues related to the influence of outliers in the datasets and possible dependencies between variables that can have an important influence on the results of calibration.

Sign in / Sign up

Export Citation Format

Share Document