Microstructure Examination of Electromagnetic Casting 2024 Aluminum Alloy Ingots

2007 ◽  
Vol 44 (6) ◽  
pp. 290-298 ◽  
Author(s):  
Aleksandra Pataric ◽  
Zvonko Gulisija ◽  
Srdjan Markovic
Keyword(s):  
Aluminum Alloy ◽  
2024 Aluminum Alloy ◽  
Electromagnetic Casting ◽  
Microstructure Examination

Hole Expansion by Using Al-Alloy Specimen and 0.45% Carbon Steel Specimen

2010 ◽  
Vol 452-453 ◽  
pp. 601-604
Author(s):  
Muhammed Sohel Rana ◽  
Md. Shafiul Ferdous ◽  
Chobin Makabe ◽  
Masaki Fujikawa
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Carbon Steel ◽  
Cold Work ◽  
Fatigue Crack Initiation ◽  
Steel Specimen ◽  
Expansion Method ◽  
Al Alloy ◽  
2024 Aluminum Alloy ◽  
Cold Worked

The enhancement method of fatigue life and the crack initiate and growth behavior of a holed specimen was investigated by using the 2024 Aluminum alloy and 0.45% Carbon steel. The purpose of present study is to propose a simple technical method for enhancement of fatigue life in a notched specimen. Also, the effect of local plastic deformation by cold work on fatigue crack initiation behavior was examined. This paper presents a basic experimental kinematic cold expansion method by inserting and removing a pin through the specimen hole. The shape of cross-section of pin was a circle or an ellipse. It was shown that the fatigue life of the specimen with the cold-worked hole was longer than that of the specimen with non-cold-worked hole for the case of same stress level in aluminum alloy and carbon steel. Also, the fatigue strength was higher in the case of the cold expanded hole. In this study, a methodology of lengthening of fatigue life of holed specimen is shown. Also, the improvement conditions of fatigue life were significantly affected by shape of pin, local hardening and residual stress conditions. The fatigue life improvement of the damaged component of structures was studied.

Effect of Coating Layer on Advanced Stud Welding of 2024 Aluminum Alloy to Galvanized and Galvannealed Steel Sheet

2014 ◽  
Vol 794-796 ◽  
pp. 351-356
Author(s):  
Yohei Harada ◽  
Kozo Ishizuka ◽  
Shinji Kumai
Keyword(s):  
Aluminum Alloy ◽  
Steel Sheet ◽  
Coating Layer ◽  
Fracture Load ◽  
Tensile Fracture ◽  
2024 Aluminum Alloy ◽  
Steel Sheets ◽  
Sheet Surface ◽  
Stud Welding ◽  
Galvannealed Steel

High strength 2024 aluminum alloy studs were joined to galvanized, galvannealed and non-coated steel sheets by using an advanced stud welding method. Effect of the coating layer on the interfacial microstructure and the tensile fracture load of the joints were evaluated. A specially-designed stud having a circular projection at its bottom was pressed against a sheet surface. A discharge current was introduced from the upper part of the stud. Local heating could be achieved by a high current density at a contact point between the projection and sheet. The observation of joint area revealed the projection was severely deformed and spread along the sheet surface. The coating layer of the galvanized steel sheet was removed at the joint interface under the charging voltage of 200 V, while that of the galvannealed one locally remained on the steel surface even at 400 V. This would be strongly related to the melting or liquidus and solidus temperatures of each coating layer. Joining was not achieved at a low charging voltage in the non-coated and galvannealed steel sheets, while high tensile fracture load was obtained even at 200 V in the galvanized ones.

Effect of precipitate coherency on the corrosion-induced hydrogen trapping in 2024 aluminum alloy

2021 ◽  
Vol 46 (69) ◽  
pp. 34487-34497
Author(s):  
H. Kamoutsi ◽  
G.N. Haidemenopoulos ◽  
H. Mavros ◽  
C. Karantonidis ◽  
P. Floratos ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Hydrogen Trapping ◽  
2024 Aluminum Alloy

An Experimental Investigation of the Yield Loci of 1100-0 Aluminum, 70:30 Brass, and an Overaged 2024 Aluminum Alloy After Various Prestrains

1986 ◽  
Vol 108 (4) ◽  
pp. 313-320 ◽  
Author(s):  
D. E. Helling ◽  
A. K. Miller ◽  
M. G. Stout
Keyword(s):  
Aluminum Alloy ◽  
Small Strain ◽  
Yield Locus ◽  
Material Behavior ◽  
Shear Stresses ◽  
2024 Aluminum Alloy ◽  
Yield Loci ◽  
Aluminum Alloy 2024 ◽  
Von Mises ◽  
Normal And Shear Stresses

The multiaxial yield behaviors of 1100-0 aluminum, 70:30 brass, and an overaged 2024 aluminum alloy (2024-T7) have been investigated for a variety of prestress histories involving combinations of normal and shear stresses. Von Mises effective prestrains were in the range of 1.2–32%. Prestress paths were chosen in order to investigate the roles of prestress and prestrain direction on the nature of small-strain offset (ε = 5 × 10−6) yield loci. Particular attention was paid to the directionality, i.e., translation and distortion, of the yield locus. A key result, which was observed in all three materials, was that the final direction of the prestrain path strongly influences the distortions of the yield loci. Differences in the yield locus behavior of the three materials were also observed: brass and the 2024-T7 alloy showed more severe distortions of the yield locus and a longer memory of their entire prestrain history than the 1100-0 aluminum. In addition, more “kinematic” translation of the subsequent yield loci was observed in brass and 2024-T7 than in 1100-0 aluminum. The 2024-T7 differed from the other materials, showing a yield locus which decreased in size subsequent to plastic straining. Finally, the implications of these observations for the constitutive modeling of multiaxial material behavior are discussed.

Corrosion Studies and Interfacial Bonding of Urea/Poly(dimethylsiloxane) Sol/Gel Hydrophobic Coatings on AA 2024 Aluminum Alloy

Langmuir ◽  
2007 ◽  
Vol 23 (10) ◽  
pp. 5505-5514 ◽  
Author(s):  
Mojca Fir ◽  
Boris Orel ◽  
Angela Šurca Vuk ◽  
Aljaž Vilčnik ◽  
Robi Ješe ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Sol Gel ◽  
Interfacial Bonding ◽  
2024 Aluminum Alloy ◽  
Hydrophobic Coatings ◽  
Corrosion Studies ◽  
Aa 2024
Sign in / Sign up

Export Citation Format

Share Document