Ductile fracture behavior of low carbon high strength steel using continuum damage mechanics

2015 ◽  
Vol 106 (9) ◽  
pp. 1010-1013 ◽  
Author(s):  
K. Priya Ajit ◽  
Abhinav Gautam ◽  
P. K. Sarkar
Keyword(s):  
Ductile Fracture ◽  
High Strength Steel ◽  
Fracture Behavior ◽  
Damage Mechanics ◽  
High Strength ◽  
Continuum Damage Mechanics ◽  
Continuum Damage ◽  
Low Carbon

Parameter Calibration for Continuum Damage Mechanics Models to Simulate Ductile Fracture of High Strength Pipeline Steels

2019 ◽  
Author(s):  
Filip Van den Abeele
Keyword(s):  
Crack Propagation ◽  
Ductile Fracture ◽  
Damage Mechanics ◽  
Void Nucleation ◽  
High Strength ◽  
Continuum Damage Mechanics ◽  
Continuum Damage ◽  
Pipeline Steels ◽  
Gtn Model ◽  
Input Parameters

Abstract The ability to arrest a running crack is one of the key features in the safe design of pipeline systems. In the industry design codes, the crack arrest properties of a pipeline should meet two requirements: crack propagation has to occur in a ductile fashion, and enough energy should be dissipated during propagation. While the first criterion is assessed by the Battelle Drop Weight Tear Test (BDWTT) at low temperatures, the latter requirement is converted into a lower bound for the impact energy absorbed during a Charpy V-notch (CVN) impact test. However, the introduction of high strength pipelines steels (X70 and beyond) has revealed that the commonly used relations based on BDWTT and CVN no longer hold. For such scenarios, Continuum Damage Mechanics (CDM) models provide promising potential to obtain a more profound understanding of the mechanisms that govern ductile crack propagation in high strength pipeline steels. In recent years, different types of CDM models have been used to simulate ductile fracture of pipeline steels. This paper focuses on two of these models, i.e. the Gurson-Tvergaard-Needleman (GTN) model and the Modified Bai-Wierzbicki (MBW) model. The GTN model is based on the computation of void growth according to Rice and Tracey, and account for the local softening of the material due to void nucleation, growth and subsequent coalescence. The MBW model is a fully coupled damage model, where the yield surface depends on both the stress triaxiality and the Lode angle. Although both models can predict ductile fracture propagation, their widespread application in pipeline design is hampered by the large number of input parameters to be calibrated. The GTN model requires 10 input parameters, i.e. 3 Tvergaard damage parameters, 4 porosity parameters and 3 parameters to describe void nucleation. Whereas the Modified Mohr-Coulomb model originally proposed by Bai and Wierzbicki uses merely 2 parameters, the extended MBW model requires no less than 18 parameters to be calibrated: 11 plasticity parameters (5 stress + 3 strain rate + 3 temperature) and 7 damage parameters (4 initiation + 1 propagation + 2 failure). In this paper, different numerical/experimental strategies to calibrate these parameter sets are reviewed and compared. Sensitivity analyses are performed to assess the influence of the different input parameters on the model predictions. For both GTN and MBW models, the robustness and uniqueness of the calibrated parameter sets is investigated. Recommendations on optimum parameter values are derived, with special emphasis on high strength pipeline steels.

Characterization of Notched Ductile Failure With Continuum Damage Mechanics

1990 ◽  
Vol 112 (4) ◽  
pp. 412-421 ◽  
Author(s):  
C. L. Chow ◽  
K. Y. Sze
Keyword(s):  
Ductile Fracture ◽  
Circular Hole ◽  
Damage Mechanics ◽  
Damage Model ◽  
Ductile Failure ◽  
Continuum Damage Mechanics ◽  
Thin Plates ◽  
Continuum Damage ◽  
Anisotropic Model ◽  
Aluminum Alloy 2024

A recently developed anisotropic model of continuum damage mechanics has been applied successfully to characterize ductile fracture of cracked plates under mode I and mixed mode failures. The damage model is further extended in this investigation to examine its applicability to include notch ductile fracture of thin plates containing a circular hole. Two hole sizes of 16 mm and 24 mm diameters are chosen and the specimen material is aluminum alloy 2024-T3. Fracture loads of the plates are predicted by the damage model and compared satisfactorily with those determined experimentally. This investigation provides an important confirmation that not only the anisotropic model of continuum damage mechanics but also the same failure criterion developed can be effectively employed to characterize both ductile fracture for plates containing an isolated macro-crack or circular hole which would otherwise not be possible using the conventional theory of fracture mechanics. The successful development of the unified approach to characterize ductile failure provides a vital impetus for design engineers in the general application of the theory of continuum damage mechanics to solve practical engineering problems.

Sign in / Sign up

Export Citation Format

Share Document