The Effect of Nanocomposite Coating with Different Concentrations on Fatigue Life of Carbon Steel AISI 1045

2013 ◽  
Vol 55 (11-12) ◽  
pp. 878-884
Author(s):  
Saad M. A Saad M. Aldousari
Keyword(s):  
Fatigue Life ◽  
Carbon Steel ◽  
Nanocomposite Coating ◽  
Aisi 1045 ◽  
Steel Aisi

Influence of On-the-Machine Laser Hardening on Machinability of Carbon Steel in Turning

2009 ◽  
Vol 407-408 ◽  
pp. 690-693
Author(s):  
Takahiko Kusano ◽  
Ryutaro Tanaka ◽  
Akira Hosokawa ◽  
Takashi Ueda ◽  
Tatsuaki Furumoto ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Carbon Steel ◽  
Hardened Steel ◽  
Laser Hardening ◽  
Hardened Zone ◽  
Spiral Form ◽  
Aisi 1045 ◽  
Steel Aisi ◽  
Turning Test ◽  
Continuous Chip

This study deals with the influence of laser hardening for a carbon steel AISI 1045 on machinability in turning. Turning test was conducted for the purpose to clarify the influence of laser hardening for steel surface on the chip controllability and surface roughness. In turning laser hardened steel, continuous chip is broken in the laser hardened zone during cutting due to higher brittleness. The broken chips have spiral form and their length is approximately equal to those generated by less than 10 revolution cutting. The surface roughness shows slightly lower compared with non-laser hardened steel.

Texture Changes of Carbon Steel and Stainless Steel as a Result of Wear

2005 ◽  
Vol 495-497 ◽  
pp. 441-446
Author(s):  
M. Reza Bateni ◽  
Jerzy A. Szpunar ◽  
X. Wang ◽  
Dong Yang Li
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Wear Test ◽  
Corrosive Wear ◽  
Fiber Texture ◽  
Corrosion Wear ◽  
Wear And Corrosion ◽  
Aisi 1045 ◽  
Steel Aisi ◽  
Wear Tests

In this research, surface texture changes of carbon steel AISI 1045 and stainless steel AISI 304 under simultaneous wear and corrosion were investigated. A solution of 3.5 % wt. NaCl was used as the corrosion agent and a pin-on-disk tribometer was employed to perform wear and corrosion wear tests.Texture investigations of the worn samples have shown texture changes after wear and corrosion-wear tests. In worn carbon steel samples after dry wear test, {011}<100> and {111} fiber texture components were developed in initially random oriented samples, whereas under corrosive-wear conditions, {111}<011> texture and {001}<110> texture were developed. In the stainless steel samples, {112}<110> texture component was observed under both dry and corrosive wear conditions, in the samples that had random grain orientations before corrosion and corrosion-wear tests.

scholarly journals The influence of laser line hardening of carbon steel AISI 1045 on the lubricated wear against steel AISI 52100

Wear ◽  
1995 ◽  
Vol 181-183 ◽  
pp. 638-647 ◽  
Author(s):  
H. Visscher ◽  
M.B. de Rooij ◽  
P.H. Vroegop ◽  
D.J. Schipper
Keyword(s):  
Carbon Steel ◽  
Laser Line ◽  
Aisi 52100 ◽  
Aisi 1045 ◽  
Steel Aisi

Ultrasound Signals Response Associated to Fatigue Failure Behaviour using Statistical Analysis

2013 ◽  
Vol 65 (1) ◽  
Author(s):  
M. M. Padzi ◽  
S. Abdullah ◽  
M. Z. Nuawi
Keyword(s):  
Carbon Steel ◽  
Fatigue Test ◽  
Fatigue Failure ◽  
Structural Changes ◽  
Energy Content ◽  
Fatigue Tests ◽  
Failure Behaviour ◽  
Aisi 1045 ◽  
Steel Aisi ◽  
Ultrasound Signals

In this paper, ultrasound signals had been analysed using a statistical-based approach to evaluate and predict fatigue failure of carbon steel AISI 1045. Fatigue tests were performed according to the ASTM E466-96 standard with the attachment of an ultrasound sensor to the tested specimen. The material used in this test was the AISI 1045 carbon steel due to its extensive application in automotive and machinery industry. Fatigue test was carried out at a constant loading stress at the sampling frequency of 8 Hz. A set of data acquisition system was used to collect those fatigue ultrasound signals. All obtained data were analysed using specific software. Ultrasound signals were collected during fatigue test in order to detect any structural changes occurs during the test. Fatigue damage characteristics were observed based on the ultrasound signals characteristics and a further analysis was performed using statistical approach. The results of signals distribution, r.m.s value and energy content of the signals were discussed to correlate fatigue failure behaviour and ultrasound signals.

scholarly journals Improvement of fatigue life of AISI 1045 carbon steel of parts obtained by turning process through feed rate

2018 ◽  
Vol 9 ◽  
pp. 243-249
Author(s):  
Khadija Kimakh ◽  
Abdelkarim Chouaf ◽  
Samir Aghzer ◽  
Amal Saoud ◽  
El hassan Malil ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Carbon Steel ◽  
Feed Rate ◽  
Turning Process ◽  
Aisi 1045

Fatigue Damage Assessment Correlating with I-Kaz Coefficient

2013 ◽  
Vol 471 ◽  
pp. 235-240
Author(s):  
Mahfodzah M. Padzi ◽  
S. Abdullah ◽  
Mohd Zaki Nuawi
Keyword(s):  
Fatigue Life ◽  
Carbon Steel ◽  
Fatigue Damage ◽  
Strain Gauge ◽  
Damage Assessment ◽  
Data Acquisition System ◽  
Sampling Frequency ◽  
Fatigue Tests ◽  
Constant Loading ◽  
Aisi 1045

This paper describes the correlation between fatigue life with the I-kaz coefficients. Fatigue tests were performed according to the ASTM E466-96 standard with a strain gauge attached to the specimen being tested. AISI 1045 carbon steel was used as the material for this test due to its wide applications in the automotive and machinery industry. Fatigue tests were carried out at several constant loading stresses of 610 MPa, 650 MPa and 690 MPa at the sampling frequency of 8 Hz. A set of data acquisition system was used to collect the fatigue strain signals. The integrated Kurtosis-based algorithm for Z-filter (I-kaz) technique had been used to find the I-kaz coefficient. The I-kaz coefficient is found to have a good correlation with fatigue life, other than can represent fatigue damage.

Sign in / Sign up

Export Citation Format

Share Document