Residual Stress in the Cementite Phase of Cold Drawn Pearlite*

2014 ◽  
Vol 69 (2) ◽  
pp. 64-70 ◽  
Author(s):  
J. Tacq ◽  
M. Kriška ◽  
M. Seefeldt
Keyword(s):  
Residual Stress ◽  
Cementite Phase

scholarly journals Synchrotron Diffraction Study of the Cementite Phase in Cold Drawn Pearlitic Steel Wires

2013 ◽  
Vol 768-769 ◽  
pp. 380-387 ◽  
Author(s):  
Jeroen Tacq ◽  
Martin Kriška ◽  
Marc Seefeldt
Keyword(s):  
Residual Stress ◽  
Diffraction Study ◽  
Pearlitic Steel ◽  
Energy Dispersive ◽  
Texture Development ◽  
Synchrotron Diffraction ◽  
Physical Mechanisms ◽  
Steel Wires ◽  
Peak Broadening ◽  
Cementite Phase

Energy dispersive synchrotron diffraction has been carried out on cold drawn pearlitic steel wires. In this paper the observed cementite peaks are analysed. For a broad range of true drawing strains sin²(Ψ) curves have been measured. The residual stress in the cementite is found to saturate after reaching a maximum at a strain of about 1.6. No indication of significant texture development in the cementite could be observed. An explanation is given in terms of possible physical mechanisms. Peak broadening was observed at the early stages of deformation.

TEM investigations of surface residual stress relaxation in A12O3 and Al2O3-SiC nanocomposite

1994 ◽  
Vol 52 ◽  
pp. 628-629
Author(s):  
J. Fang ◽  
H. M. Chan ◽  
M. P. Harmer
Keyword(s):  
Residual Stress ◽  
Single Phase ◽  
Stress Relief ◽  
Stress Recovery ◽  
Surface Residual Stress ◽  
Microscopic Mechanism ◽  
Sic Particles ◽  
Annealing Procedure ◽  
The Difference ◽  
Nano Size

It was Niihara et al. who first discovered that the fracture strength of Al2O3 can be increased by incorporating as little as 5 vol.% of nano-size SiC particles (>1000 MPa), and that the strength would be improved further by a simple annealing procedure (>1500 MPa). This discovery has stimulated intense interest on Al2O3/SiC nanocomposites. Recent indentation studies by Fang et al. have shown that residual stress relief was more difficult in the nanocomposite than in pure Al2O3. In the present work, TEM was employed to investigate the microscopic mechanism(s) for the difference in the residual stress recovery in these two materials.Bulk samples of hot-pressed single phase Al2O3, and Al2O3 containing 5 vol.% 0.15 μm SiC particles were simultaneously polished with 15 μm diamond compound. Each sample was cut into two pieces, one of which was subsequently annealed at 1300° for 2 hours in flowing argon. Disks of 3 mm in diameter were cut from bulk samples.

Residual stress measurements and modeling of built-up Box-T sections

2021 ◽  
Vol 160 ◽  
pp. 107336
Author(s):  
Ziqian Zhang ◽  
Gang Shi ◽  
Xuesen Chen ◽  
Lijun Wang ◽  
Le Zhou
Keyword(s):  
Residual Stress ◽  
Stress Measurements

Comparative study of the effective parameters on residual stress relaxation in welded aluminum plates under cyclic loading

2020 ◽  
Vol 21 (5) ◽  
pp. 505
Author(s):  
Yousef Ghaderi Dehkordi ◽  
Ali Pourkamali Anaraki ◽  
Amir Reza Shahani
Keyword(s):  
Residual Stress ◽  
Cyclic Loading ◽  
Stress Relaxation ◽  
Stress Amplitude ◽  
Cyclic Plasticity ◽  
Mean Stress ◽  
Effective Parameters ◽  
Perfect Plasticity ◽  
Residual Stress Relaxation ◽  
Aluminum Plates

The prediction of residual stress relaxation is essential to assess the safety of welded components. This paper aims to study the influence of various effective parameters on residual stress relaxation under cyclic loading. In this regard, a 3D finite element modeling is performed to determine the residual stress in welded aluminum plates. The accuracy of this analysis is verified through experiment. To study the plasticity effect on stress relaxation, two plasticity models are implemented: perfect plasticity and combined isotropic-kinematic hardening. Hence, cyclic plasticity characterization of the material is specified by low cycle fatigue tests. It is found that the perfect plasticity leads to greater stress relaxation. In order to propose an accurate model to compute the residual stress relaxation, the Taguchi L18 array with four 3-level factors and one 6-level is employed. Using statistical analysis, the order of factors based on their effect on stress relaxation is determined as mean stress, stress amplitude, initial residual stress, and number of cycles. In addition, the stress relaxation increases with an increase in mean stress and stress amplitude.

Sign in / Sign up

Export Citation Format

Share Document