scholarly journals Effect of Re and Tm-site on morphology structure and optical band gap of ReTmO3 (Re: La, Ce, Nd, Gd, Dy, Y and Tm: Fe, Cr) prepared by sol-gel method

2018 ◽  
Vol 64 (4) ◽  
pp. 381
Author(s):  
Muhammad Tufiq Jamil ◽  
Javed Ahmad ◽  
Syed Hamad Bukhari ◽  
Murtaza Saleem
Keyword(s):  
Band Gap ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
Orthorhombic Crystal ◽  
X Ray ◽  
Average Grain Size ◽  
Auto Combustion ◽  
Uv Visible

Rare earth nano sized pollycrystalline orthoferrites and orthocromites ReT mO3 (Re = La, Nd, Gd, Dy, Y and T m = Fe, Cr) have been synthesized by sol-gel auto combustion citrate method. The samples have been characterized by means of X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), and UV-visible spectroscopy. The samples are single phase as confirmed by XRD analysis and correspond to the orthorhombic crystal symmetry with space group pbnm. Debye Scherer formula and Williamson Hall analysis have been used to calculate the average grain size which is consistent with that of determined from SEM analysis and varied between 25-75 nm. The elemental compositions of all samples have been checked by EDX analysis. Different crystallographic parameters are calculated with strong structural correlation among Re and Tm sites. The optical energy band gap has been calculated by using Tauc relation estimated to be in the range of 1.77 - 1.87 eV and 2.77 - 3.14 eV, for ReFeO3 and ReCrO3, respectively.

Hierarchical Nanostructured ZnO-CuO Nanocomposite and its Photocatalytic Activity

2015 ◽  
Vol 35 ◽  
pp. 21-26 ◽  
Author(s):  
Susmita Das ◽  
Vimal Chandra Srivastava
Keyword(s):  
Photocatalytic Activity ◽  
Pure Copper ◽  
Ultra Violet ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ultra Violet Radiation ◽  
One Step ◽  
Uv Visible

Metal oxide nanocomposite (ZnO-CuO) was successfully synthesized by one step homogeneous coprecipitation method and further characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron micrograph (SEM), X-ray diffraction analysis (XRD) and UV-visible diffuse reflectance spectra. XRD analysis exhibited presence of pure copper oxide and zinc oxide within the nanocomposite. SEM analysis indicated that the ZnO-CuO nanocomposite was consisted of flower shaped ZnO along with leaf shaped CuO. Photocatalytic activity of nanocomposite was evaluated in terms of degradation of methylene blue (MB) dye solution under ultra-violet radiation. Results showed that the photocatalytic efficiency of ZnO-CuO nanocomposite was higher than its individual pure oxides (ZnO or CuO).

scholarly journals Nanosized LaCo0.6Fe0.4O3 perovskites synthesized by citrate sol gel auto combustion method

2014 ◽  
Vol 8 (2) ◽  
pp. 87-92 ◽  
Author(s):  
Unikoth Megha ◽  
Karakat Shijina ◽  
George Varghese
Keyword(s):  
Sol Gel ◽  
Combustion Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dense Microstructure ◽  
Metal Nitrates ◽  
Average Grain Size ◽  
Auto Combustion ◽  
Different Temperatures ◽  
Lcr Meter

LaCo0.6Fe0.4O3 (LCFO) nanopowder was synthesized from constituent metal nitrates, citric acid and ethylene glycol by citrate sol gel autocombustion method and calcined at different temperatures. The powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX) and Fourier transform infrared spectra (FTIR), whereas dielectric properties were investigated with LCR-meter. The FTIR spectra, taken for the xerogel and the sample calcined at 1000?C, confirm that the organic groups were removed during calcination and oxide structure was formed. The XRD result shows that LCFO has rhombhohedral crystal structure with R-3C space group and forms single phase after calcination at 600?C. The activation energy of crystallite growth, determined from the Arrhenius plot, was 17?2 kJ/mol. Surface feature studies of the powders were obtained from SEM. At 1000?C, dense microstructure with wellshaped grain boundaries was obtained and the average grain size was around 400 nm. EDAX confirms the elemental composition. Finally, from the dielectric studies, it was found that the dielectric constant (?r) as well as dielectric loss tangent (tan ?) decreases with increase in frequency.

scholarly journals Y3+ substituted Sr-hexaferrites: sol-gel synthesis, structural, magnetic and electrical characterization

Cerâmica ◽  
2019 ◽  
Vol 65 (374) ◽  
pp. 274-281 ◽  
Author(s):  
S. S. Satpute ◽  
S. R. Wadgane ◽  
S. R. Kadam ◽  
D. R. Mane ◽  
R. H. Kadam
Keyword(s):  
Electron Microscopy ◽  
Sol Gel ◽  
Electrical Characterization ◽  
Combustion Method ◽  
Hexagonal Structure ◽  
Strontium Hexaferrite ◽  
X Ray Diffraction ◽  
X Ray ◽  
Morphological Studies ◽  
Auto Combustion

Abstract Y3+ substituted strontium hexaferrites having chemical composition SrYxFe12-xO19 (x= 0.0, 0.5, 1.0, 1.5) were successfully synthesized by sol-gel auto-combustion method. The structural and morphological studies of prepared samples were investigated by using X-ray diffraction technique, energy dispersive X-ray spectroscopy, field emission scanning electron microscopy (FE-SEM) and high-resolution transmission electron microscopy. The X-ray diffraction pattern confirmed the single-phase hexagonal structure of yttrium substituted strontium ferrite and the lattice parameters a and c increased with the substitution of Y3+ ions. The crystallite size also varied with x content from 60 to 80 nm. The morphology was studied by FE-SEM, and the grain size of nanoparticles ranged from 44 to 130 nm. The magnetic properties were investigated by using vibrating sample magnetometer. The value of saturation magnetization decreased from 49.60 to 35.40 emu/g. The dielectric constant decreased non-linearly whereas the electrical dc resistivity increased with the yttrium concentration in strontium hexaferrite.

scholarly journals Green synthesis and characterization of hexaferrite strontium-perovskite strontium photocatalyst nanocomposites

2020 ◽  
Vol 43 (1) ◽  
pp. 26-42 ◽  
Author(s):  
Zahra Hajian Karahroudi ◽  
Kambiz Hedayati ◽  
Mojtaba Goodarzi
Keyword(s):  
Magnetic Properties ◽  
Green Synthesis ◽  
Sol Gel ◽  
Synthesis Method ◽  
Combustion Method ◽  
Lemon Juice ◽  
X Ray Diffraction ◽  
X Ray ◽  
Auto Combustion

AbstractThis study presents a preparation of SrFe12O19– SrTiO3 nanocomposite synthesis via the green auto-combustion method. At first, SrFe12O19 nanoparticles were synthesized as a core and then, SrTiO3 nanoparticles were prepared as a shell for it to manufacture SrFe12O19–SrTiO3 nanocomposite. A novel sol-gel auto-combustion green synthesis method has been used with lemon juice as a capping agent. The prepared SrFe12O19–SrTiO3 nanocomposites were characterized by using several techniques to characterize their structural, morphological and magnetic properties. The crystal structures of the nanocomposite were investigated via X-ray diffraction (XRD). The morphology of SrFe12O19– SrTiO3 nanocomposite was studied by using a scanning electron microscope (SEM). The elemental composition of the materials was analyzed by an energy-dispersive X-ray (EDX). Magnetic properties and hysteresis loop of nanopowder were characterized via vibrating sample magnetometer (VSM) in the room temperature. Fourier transform infrared spectroscopy (FTIR) spectra of the samples showed the molecular bands of nanoparticles. Also, the photocatalytic behavior of nanocomposites has been checked by the degradation of azo dyes under irradiation of ultraviolet light.

ITO Thin Films on Silicon Buffer by Sol Gel Method

2006 ◽  
Vol 514-516 ◽  
pp. 1155-1160 ◽  
Author(s):  
Talaat Moussa Hammad
Keyword(s):  
Thin Films ◽  
Indium Tin Oxide ◽  
Optical Transmission ◽  
Sol Gel ◽  
Precursor Solution ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ito Thin Films ◽  
Uv Visible

Sol gel indium tin oxide thin films (In: Sn = 90:10) were prepared by the sol-gel dipcoating process on silicon buffer substrate. The precursor solution was prepared by mixing SnCl2.2H2O and InCl3 dissolved in ethanol and acetic acid. The crystalline structure and grain orientation of ITO films were determined by X-ray diffraction. The surface morphology of the films was characterized by scanning electron microscope (SEM). Optical transmission and reflectance spectra of the films were analyzed by using a UV-visible spectrophotometer. The transport properties of majority charge carriers for these films were studied by Hall measurement. ITO thin film with electrical resistivity of 7.6 ×10-3 3.cm, Hall mobility of approximately 2 cm2(Vs)-1 and free carrier concentration of approximately 4.2 ×1020 cm-3 are obtained for films 100 nm thick films. The I-V curve measurement showed typical I-V characteristic behavior of sol gel ITO thin films.

Structural, Magnetic and Dielectric Analysis of Higher Magnetic Mn Doped Zn-Cr Oxide Nanoparticles

2021 ◽  
Vol 9 (VI) ◽  
pp. 95-102
Author(s):  
S. D. Balsure
Keyword(s):  
Type Strain ◽  
Sol Gel ◽  
Hexagonal Wurtzite Structure ◽  
Xrd Analysis ◽  
Oxide Nanoparticles ◽  
X Ray Diffraction ◽  
Microstructural Parameters ◽  
Auto Combustion ◽  
Mn Doped ◽  
Combustion Technique

Higher magnetic Mn doped Zn-Cr oxide nanoparticles with general compositional formula MxZn0.95-xCr0.05O have been synthesized by using sol-gel auto combustion technique. Room temperature X-ray diffraction (XRD) technique has been employed to study the structural and microstructural parameters of the as-prepared samples. XRD analysis confirms the phase purity and hexagonal wurtzite structure of all the samples. Replacement of Zn2+ ions by Mn2+ ions shifts peak positions slightly towards the lower angles which in turn expands the lattice lengths ‘a’ from 3.2487 to 3.2528 Å and ‘c’ from 5.2043 to 5.2118 Å. Crystallite size obtained from Scherrer equation was confirmed by Williamson – Hall (W-H) and size – strain plot methods (SSP). Both W-H and SSP methods reveals the tensile type strain for undoped sample and comprehensive type strain for Mn2+ doped samples. Magnetic properties were investigated by using vibrating sample magnetometer. Diluted ferromagnetic behaviour is observed for all the samples and saturation magnetization (MS) increases from 0.0514 to 0.1163 emu/gm. Two-probe technique was employed to understand the dielectric behaviour of the samples as a function of frequency. At lower frequency region, both dielectric constant () and dielectric loss tangent (tan ) shows higher values and decreases with the increasing applied frequency.

Development of Ternary Concrete Utilizing Agricultural Waste Material

2022 ◽  
Author(s):  
Sunita Kumari ◽  
Dhirendra Singhal ◽  
Rinku Walia ◽  
Ajay Rathee
Keyword(s):  
Rice Husk ◽  
Rice Husk Ash ◽  
Agricultural Waste ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Concrete Mix ◽  
Maize Cob

Abstract The present project proposes to utilize rice husk and maize cob husk ash in the cement to mitigate the adverse impact of cement on environment and to enhance the disposal of waste in a sustainable manner. Ternary concrete / MR concrete was prepared by using rise husk and maize cob ash with cement. For the present project, five concrete mixes MR-0 (Control mix), MR-1 (Rice husk ash 10% and MR-2.5%), MR-2 (Rice husk ash 10% and MR-5%), MR-3 (Rice husk ash 10% and MR-2.5%), MR-4 (Rice husk ash 10% and MR-2.5%) were prepared. M35 concrete mix was designed as per IS 10262:2009 for low slump values 0-25mm. The purpose is to find the optimum replacement level of cement in M35 grade ternary concrete for I – Shaped paver blocks.In order to study the effects of these additions, micro-structural and structural properties test of concretes have been conducted. The crystalline properties of control mix and modified concrete are analyzed by Fourier Transform Infrared Spectroscope (FTIR), Scanning Electron Microscopy (SEM), and X-Ray Diffraction (XRD). The results indicated that 10% Rice husk ash and 5% maize cob ash replaced with cement produce a desirable quality of ternary concrete mix having good compressive strength. The results of SEM analysis indicated that the morphology of both concrete were different, showing porous structure at 7 days age and become unsymmetrical with the addition of ashes. After 28 day age, the control mix contained more quantity of ettringite and became denser than ternary concrete. XRD analysis revealed the presence of portlandite in large quantity in controlled mix concrete while MR concrete had the partially hydrated particle of alite.

Synthesis of Nanocomposites of V2OO5©Selenium Nanoparticles and Multiwalled Carbon Nanotubes for Antimicrobial Activity

2021 ◽  
Vol 21 (11) ◽  
pp. 5673-5680
Author(s):  
Muthukrishnan Francklin Philips ◽  
Jothirathinam Thangarathinam ◽  
Jayakumar Princy ◽  
Cyril Arockiaraj Crispin Tina ◽  
Cyril Arockiaraj Crispin Tina ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Antimicrobial Activity ◽  
Multiwalled Carbon Nanotubes ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Multiwalled Carbon ◽  
X Ray ◽  
Functionalized Multiwalled Carbon Nanotubes ◽  
Uv Visible ◽  
Micro Organisms

The authors report the preparation of the nanocomposite comprising of vanadium pentoxide (V2O5) and selenium (Se) nanoparticles and functionalized multiwalled carbon nanotubes (MWCNTs) (V2O5@Se NPs/MWCNTs). Since Se NPs possesses extraordinary physicochemical properties including larger surface area with higher adsorption capacity, V2O5 NPs were adsorbed onto Se NPs surface through physisorption process (designated as V2O5@Se NPs). The nanocomposite synthesized hydrothermally was evaluated for its antimicrobial activity. The morphology and microstructure of the nanocomposite were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis, respectively. Fourier transform infrared spectroscopy (FTIR) and UV-Visible spectroscopy (UV-Vis) were employed to analyze the spectral properties of nanocomposite. The microbicidal efficacy of nanocomposite was tested against Gram-negative (G-)ZGram-positive (G+) bacteria and fungus. This is the first report on the synthesis of V2O5@Se NPs/MWCNTs nanocomposites by chemical method that showed microbicidal effect on micro-organisms. The thiol (-SH) units facilitates the enrichment of V2O5@Se NPs onto MWCNTs surface. Ultimately, it reflects on the significant antimicrobial activity of V2O5@Se NPs/MWCNTs.

Facile Electrospinning Preparation of Y3Al5O12 Nanobelts

2013 ◽  
Vol 448-453 ◽  
pp. 3041-3045
Author(s):  
Fei Bi ◽  
Xiang Ting Dong ◽  
Jin Xian Wang ◽  
Gui Xia Liu ◽  
Wen Sheng Yu
Keyword(s):  
Sol Gel ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
Ftir Analysis ◽  
X Ray ◽  
Novel Structure ◽  
Group I ◽  
Sol Gel Process ◽  
Composite Nanobelts ◽  
Scanning Electron

PVP/[Y(NO3)3+Al (NO3)3] composite nanobelts were fabricated via electrospinning combined with sol-gel process and novel structure of Y3Al5O12(denoted as YAG for short) nanobelts have been obtained after calcination of the relevant composite nanobelts. The structural properties were characterized by X-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XRD analysis indicated that the composite nanobelts were amorphous, and YAG nanobelts were cubic in structure with space group Ia3d. FTIR analysis manifested that pure YAG nanobelts were formed at 900oC. SEM analysis and histograms revealed that the width of the composite nanobelts and YAG nanobelts were 3.5 μm and 2.4 μm, and the thickness were 240 nm and 112 nm, respectively, under the 95% confidence level. The formation mechanism of YAG nanobelts was discussed in detail.

Sign in / Sign up

Export Citation Format

Share Document