scholarly journals FUNDAMENTAL STUDY ON EVALUATION OF STRUCTURAL PERFORMANCE OF REINFORCED CONCRETE BEAM DAMAGED BY CORROSION OF LONGITUDINAL TENSILE MAIN REBAR BY FINITE ELEMENT METHOD

1998 ◽  
Vol 63 (506) ◽  
pp. 43-50 ◽  
Author(s):  
Han seung LEE ◽  
Takafumi NOGUCHI ◽  
Fuminori TOMOSAWA
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Structural Performance ◽  
Fundamental Study ◽  
Element Method

scholarly journals Computer Analysis of Dynamic Reliability of Some Concrete Beam Structure Exhibiting Random Damping

2021 ◽  
Vol 26 (1) ◽  
pp. 45-64
Author(s):  
R. Bredow ◽  
M. Kamiński
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Concrete Beam ◽  
Perturbation Technique ◽  
Probabilistic Approach ◽  
Engineering Application ◽  
Stochastic Perturbation ◽  
Reinforced Concrete Beam ◽  
Dynamic Reliability ◽  
Element Method

Abstract An efficiency of the generalized tenth order stochastic perturbation technique in determination of the basic probabilistic characteristics of up to the fourth order of dynamic response of Euler-Bernoulli beams with Gaussian uncertain damping is verified in this work. This is done on civil engineering application of a two-bay reinforced concrete beam using the Stochastic Finite Element Method implementation and its contrast with traditional Monte-Carlo simulation based Finite Element Method study and also with the semi-analytical probabilistic approach. The special purpose numerical implementation of the entire Stochastic perturbation-based Finite Element Method has been entirely programmed in computer algebra system MAPLE 2019 using Runge-Kutta-Fehlberg method. Further usage of the proposed technique to analyze stochastic reliability of the given structure subjected to dynamic oscillatory excitation is also included and discussed here because of a complete lack of the additional detailed demands in the current European designing codes.

Simulation Behavior of Flexure in Reinforced Concrete Beam with Opening Reinforced with Glass Fiber Reinforced Polymer (GFRP)

2016 ◽  
Vol 857 ◽  
pp. 421-425
Author(s):  
Saif M. Thabet ◽  
S.A. Osman
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Glass Fiber ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

This paper presents an investigation into the flexural behaviour of reinforced concrete beam with opening reinforced with two different materials i.e., steel and Glass Fiber Reinforced Polymer (GFRP). Comparison study between the two different materials were carried out and presented in this study through non-linear Finite Element Method (FEM) using the commercial ABAQUS 6.10 software package. The performance of the opening beam reinforced with GFRP is influenced by several key parameters. Simulation analyses were carried out to determine the behavior of beam with opening subjected to monotonic loading. The main parameters considered in this study are size of opening and reinforcement diameter. The results show that GFRP give 23%-29% more ductility than steel reinforcement. The result also shows when the size of opening change from 200mm to 150mm or from 150mm to 100mm the ultimate load capacity increase by 15%. In general, good agreement between the Finite Element (FE) simulation and the available experimental result has been obtained.

scholarly journals Numerical Derivation of Iso-Damaged Curve for a Reinforced Concrete Beam Subjected to Blast Loading

2018 ◽  
Vol 149 ◽  
pp. 02016 ◽  
Author(s):  
Yehya Temsah ◽  
Ali Jahami ◽  
Jamal Khatib ◽  
M Sonebi
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Shock Waves ◽  
Concrete Beam ◽  
Blast Loading ◽  
Reinforced Concrete Beam ◽  
Structural Elements ◽  
Finite Element Program ◽  
Element Program ◽  
Structural Engineers

Many engineering facilities are severely damaged by blast loading. Therefore, many manufacturers of sensitive, breakable, and deformed structures (such as facades of glass buildings) carry out studies and set standards for these installations to withstand shock waves caused by explosions. Structural engineers also use these standards in their designs for various structural elements by following the ISO Damage Carve, which links pressure and Impulse. As all the points below this curve means that the structure is safe and will not exceed the degree of damage based on the various assumptions made. This research aims to derive the Iso-Damage curve of a reinforced concrete beam exposed to blast wave. An advanced volumetric finite element program (ABAQUS) will be used to perform the derivation.

Uniform loading on the reinforced concrete beam produced by the specific cylinder-shaped rubber bags fully filled with air or water

2020 ◽  
Vol 23 (9) ◽  
pp. 1934-1947
Author(s):  
Dapeng Chen ◽  
Li Chen ◽  
Qin Fang ◽  
Yuzhou Zheng ◽  
Teng Pan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Element Model ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Uniform Loading ◽  
Air Bag

The bending behavior of reinforced concrete beams under uniform pressure is critical for the research of the blast-resistance performance of structural components under explosive loads. In this study, a bending test of five reinforced concrete beams with the dimensions of 200 mm (width) × 200 mm (depth) × 2500 mm (length) under uniform load produced by a specific cylinder-shaped rubber bag filled with air or water was conducted to investigate their flexural performances. An air bag load was applied to three of the reinforced concrete beams, a water bag load was applied to one reinforced concrete beam, and the remainder beam was subjected to the 4-point bending load. The experimental results highlighted that the air bag and water bag loading methods can be used to effectively apply uniform loads to reinforced concrete beams. Moreover, the stiffness of the air bag was improved by 123% in accordance with the initial pressure increases from 0.15 to 0.45 MPa. In addition, a finite element model of the test loading system was established using ABAQUS/Standard software. Moreover, the critical factors of the air bag loading method were analyzed using the numerical model. The calculated results were found to be in good agreement with the test data. The established finite element model can therefore be used to accurately simulate the action performances of the uniform loading technique using rubber bags filled with air or water.

scholarly journals MODAL ANALYSIS OF REINFORCED CONCRETE AND FIBER CONCRETE BEAMS

2021 ◽  
Vol 3 (1) ◽  
pp. 95-105
Author(s):  
T. Makovkina ◽  
◽  
M. Surianinov ◽  
O. Chuchmai ◽  
◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Computer Modeling ◽  
Natural Frequencies ◽  
Concrete Beams ◽  
The Finite Element Method ◽  
Fiber Concrete ◽  
Experimental Researches ◽  
Element Method

Analytical, experimental and numerical results of determination of natural frequencies and forms of oscillations of reinforced concrete and fiber concrete beams are given. Modern analytical, numerical and experimental methods of studying the dynamics of reinforced concrete and fiber concrete beams are analyzed. The problem of determining the natural frequencies and forms of oscillations of reinforced concrete and fiber concrete beams at the initial modulus of elasticity and taking into account the nonlinear diagram of deformation of materials is solved analytically. Computer modeling of the considered constructions in four software complexes is done and the technique of their modal analysis on the basis of the finite element method is developed. Experimental researches of free oscillations of the considered designs and the comparative analysis of all received results are carried out. It is established that all involved complexes determine the imaginary frequency and imaginary form of oscillations. The frequency spectrum calculated by the finite element method is approximately 4% lower than that calculated analytically; the results of the calculation in SOFiSTiK differ by 2% from the results obtained in the PC LIRA; the discrepancy with the experimental data reaches 20%, and all frequencies calculated experimentally, greater than the frequencies calculated analytically or by the finite element method. This rather significant discrepancy is explained, according to the authors, by the incorrectness of the used dynamic model of the reinforced beam. The classical dynamics of structures is known to be based on the theory of linear differential equations, and the oscillations of structures are considered in relation to the unstressed initial state. It is obvious that in the study of free and forced oscillations of reinforced concrete building structures such an approach is unsuitable because they are physically nonlinear systems. The concept of determining the nonlinear terms of these equations is practically not studied. Numerous experimental researches and computer modeling for the purpose of qualitative and quantitative detection of all factors influencing a spectrum of natural frequencies of fluctuations are necessary here.

Sign in / Sign up

Export Citation Format

Share Document