scholarly journals In-situ hydrogen wettability characterisation for Underground Hydrogen Storage

2021 ◽  
Author(s):  
Scott Higgs ◽  
Ying Da Wang ◽  
Chenhao Sun ◽  
Jonathan Ennis-King ◽  
Samuel Jackson ◽  
...  
Keyword(s):  
Contact Angle ◽  
Hydrogen Storage ◽  
Distilled Water ◽  
Pendant Drop ◽  
Micro Computed Tomography ◽  
Gas Reservoirs ◽  
Effective Contact ◽  
Depleted Gas Reservoirs ◽  
Term Energy

Hydrogen storage in subsurface aquifers or depleted gas reservoirs represents a viable seasonal and/or long-term energy storage solution. However, currently, there is a scarcity of subsurface petrophysical data for the hydrogen system, limiting modelling work and industrial rollout. In this work, we address the knowledge gap by determining the wettability and Interfacial Tension (IFT) of the hydrogen-brine-quartz system using a multi-modal, in-situ approach. We utilise the captive bubble, pendant drop and in-situ 3D micro-Computed Tomography (CT) methods to rigorously characterise a hydrogen-brine-Bentheimer rock system, applicable to high quartz sandstone storage systems generally. The captive bubble method determined the effective contact angle ranged between 29°-39° for pressures 6.89-20.68MPa and salinities from distilled water to 5000ppm NaCl brine. In-situ methods confirmed the water-wet system with the mean of the macroscopic and apparent contact angle distributions being 39.77° and 59.75° respectively. Further confirmation of the water-wet system was provided by curvature analysis of fluid clusters. The pendant drop method determined that IFT decreased with increasing pressure in distilled water from 72.45 mN/m at 6.89MPa to 69.43 mN/m at 20.68MPa. No correlation was found between IFT and salinity for the 1000ppm and 5000ppm brines. Our fundamental studies provide insights into the physics of hydrogen wetting in multiphase environments of subsurface reservoirs. With this, we can make informed estimates of relative permeability and capillary pressure for the hydrogen-brine system to model the storage capacity and withdrawal rate of hydrogen in target reservoirs.

Magazynowanie wodoru w obiektach geologicznych

Nafta-Gaz ◽  
2020 ◽  
Vol 76 (11) ◽  
pp. 794-798
Author(s):  
Piotr Such ◽  
Keyword(s):  
Hydrogen Storage ◽  
Oil And Gas ◽  
Renewable Energy Sources ◽  
Distribution Networks ◽  
Extensive Study ◽  
Operational Parameters ◽  
Gas Reservoirs ◽  
Depleted Gas Reservoirs ◽  
Chemical Companies ◽  
Salt Caverns

Hydrogen economy became one of the main directions in EU’s Green Deal for making Europe climate neutral in 2050. Hydrogen will be produced with the use of renewable energy sources or it will be obtained from coking plants and chemical companies. It will be applied as ecological fuel for cars and as a mix with methane in gas distribution networks. Works connected with all aspects of hydrogen infrastructure are conducted in Poland. The key problem in creating a hydrogen system is hydrogen storage. They ought to be underground (RES) because of their potential volume. Three types of underground storages are taken into account. There are salt caverns, exploited gas reservoirs and aquifers. Salt caverns were built in Poland and now they are fully operational methane storages. Oli and Gas Institute – National Research Institute has been collaborating with the Polish Oil and Gas Company since 1998. Salt cavern storage exists and is used as methane storages. Now it is possible to use them as methane-hydrogen mixtures storages with full control of all operational parameters (appropriate algorithms are established). Extensive study works were carried out in relation to depleted gas reservoirs/aquifers: from laboratory investigations to numerical modelling. The consortium with Silesian University of Technology was created, capable of carrying out all possible projects in this field. The consortium is already able to undertake the project of adapting the depleted field to a methane-hydrogen storage or, depending on the needs, to a hydrogen storage. All types of investigations of reservoir rocks and reservoir fluids will be taken into consideration.

scholarly journals Pore-scale experimental investigation of oil recovery enhancement in oil-wet carbonates using carbonaceous nanofluids

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Bingjun Zhang ◽  
Abdelhalim I. A. Mohamed ◽  
Lamia Goual ◽  
Mohammad Piri
Keyword(s):  
Contact Angle ◽  
Oil Recovery ◽  
Three Dimensional ◽  
Wettability Alteration ◽  
Distribution Analysis ◽  
Pore Scale ◽  
Core Flooding ◽  
Micro Computed Tomography ◽  
Carbon Nanosheets

Abstract This study investigates the pore-scale displacement mechanisms of crude oil in aged carbonate rocks using novel engineered carbon nanosheets (E-CNS) derived from sub-bituminous coal. The nanosheets, synthesized by a simple top-down technique, were stable in brine without any additional chemicals. Owing to their amphiphilic nature and nano-size, they exhibited dual properties of surfactants and nanoparticles and reduced the oil/brine interfacial tension (IFT) from 14.6 to 5.5 mN/m. X-ray micro-computed tomography coupled with miniature core-flooding was used to evaluate their ability to enhance oil recovery. Pore-scale displacement mechanisms were investigated using in-situ contact angle measurements, oil ganglia distribution analysis, and three-dimensional visualization of fluid occupancy maps in pores of different sizes. Analysis of these maps at the end of various flooding stages revealed that the nanofluid invaded into medium and small pores that were inaccessible to base brine. IFT reduction was identified as the main displacement mechanism responsible for oil recovery during 1 to 8 pore volumes (PVs) of nanofluid injection. Subsequently, wettability alteration was the dominant mechanism during the injection of 8 and 32 PVs, decreasing the average contact angle from 134° (oil wet) to 85° (neutral wet). In-situ saturation data reveals that flooding with only 0.1 wt% of E-CNS in brine resulted in incremental oil production of 20%, highlighting the significant potential of this nanofluid as a recovery agent.

scholarly journals Regeneration of critical-sized defects, in a goat model, using a dextrin-based hydrogel associated with granular synthetic bone substitute

2020 ◽  
Author(s):  
Isabel Pereira ◽  
José Eduardo Pereira ◽  
Luís Maltez ◽  
Alexandra Rodrigues ◽  
Catarina Rodrigues ◽  
...  
Keyword(s):  
Bone Regeneration ◽  
Bone Substitute ◽  
Bone Substitutes ◽  
Multipotent Mesenchymal Stromal Cells ◽  
Micro Computed Tomography ◽  
Synthetic Bone Substitute ◽  
In Situ Forming ◽  
Bioactive Agents ◽  
In Situ Forming Hydrogels

Abstract The development of injectable bone substitutes (IBS) have obtained great importance in the bone regeneration field, as a strategy to reach hardly accessible defects using minimally invasive techniques and able to fit to irregular topographies. In this scenario, the association of injectable hydrogels and bone graft granules is emerging as a well-established trend. Particularly, in situ forming hydrogels have arisen as a new IBS generation. An in situ forming and injectable dextrin-based hydrogel (HG) was developed, aiming to act as a carrier of granular bone substitutes and bioactive agents. In this work, the HG was associated to a granular bone substitute (Bonelike®) and implanted in goat critical-sized calvarial defects (14 mm) for 3, 6 and 12 weeks. The results showed that HG improved the handling properties of the Bonelike® granules and did not affect its osteoconductive features, neither impairing the bone regeneration process. Human multipotent mesenchymal stromal cells from the umbilical cord, extracellular matrix hydrolysates and the pro-angiogenic peptide LLKKK18 were also combined with the IBS. These bioactive agents did not enhance the new bone formation significantly under the conditions tested, according to micro-computed tomography and histological analysis.

Penetration Dynamics of Solid Particles into Liquids High-Speed Experimental Results and Modelling

2005 ◽  
Vol 473-474 ◽  
pp. 429-434 ◽  
Author(s):  
Olga Verezub ◽  
György Kaptay ◽  
Tomiharu Matsushita ◽  
Kusuhiro Mukai
Keyword(s):  
Contact Angle ◽  
Particle Size ◽  
Aqueous Solutions ◽  
Particle Velocity ◽  
Weber Number ◽  
High Speed ◽  
Solid Particles ◽  
Bulk Liquid ◽  
Distilled Water ◽  
Critical Weber Number

Penetration of model solid particles (polymer, teflon, nylon, alumina) into transparent model liquids (distilled water and aqueous solutions of KI) were recorded by a high speed (500 frames per second) camera, while the particles were dropped from different heights vertically on the still surface of the liquids. In all cases a cavity has been found to form behind the solid particle, penetrating into the liquid. For each particle/liquid combination the critical dropping height has been measured, above which the particle was able to penetrate into the bulk liquid. Based on this, the critical impact particle velocity, and also the critical Weber number of penetration have been established. The critical Weber number of penetration was modelled as a function of the contact angle, particle size and the ratio of the density of solid particles to the density of the liquid.

scholarly journals Effect of 2% Lignocaine Solution in Pain During Removal of Nasal Pack

2019 ◽  
Vol 15 (2) ◽  
pp. 80-83
Author(s):  
Ashish Dhakal ◽  
Bikash Lal Shrestha ◽  
Monika Pokharel
Keyword(s):  
Normal Saline ◽  
Saline Group ◽  
Nasal Packing ◽  
Distilled Water ◽  
Left Nostril ◽  
Normal Saline Group ◽  
Nasal Pack ◽  
Control Side ◽  
Group 5

Background: Nasal packing is commonly done after septal surgeries. Nonabsorbable nasal pack is used to minimize bleeding from surgery site, support the mucoperichondrial flaps, and minimize the risk of formation of septal hematomas and adhesions. However, these materials cause pain and discomfort in-situ as well as during removal. This study was done to evaluate the effect of 2% lignocaine rehydration of nasal pack on pain during pack removal. Methods: This prospective study was conducted on 60 patients who had undergone septoplasty. The patients were divided into 2 groups: Lignocaine and Normal saline group, with 30 patients each. In the Lignocaine group, 2.5 ml of 2% of lignocaine was diluted with 2.5 ml of distilled water and was injected into the nasal pack; and in Normal saline group, 5 ml of normal saline was injected into the nasal pack. Nothing was injected to the left nostril, which acted as a control, in both groups. All patients were asked severity of pain during removal of nasal packing by VAS. Results: In lignocaine group, mean pain score was 3.73 ± 1.63 on lignocaine side and 6.23 ± 1.69 on control side (U=109.5, p<0.001). In Normal saline group, it was 6.5 ± 1.7 on normal saline side and 6.23 ± 1.96 on control side (U=425.5, p=0.711). On comparing VAS between lignocaine and normal saline group, pain was significantly lower in the lignocaine group (U=112.5, p<0.001) Conclusion: Rehydrating nasal pack with 2% topical lignocaine is a useful method to reduce pain during nasal pack removal.

Catalytic effect of in situ formed Mg2Ni and REH (RE: Ce and Y) on thermodynamics and kinetics of Mg-RE-Ni hydrogen storage alloy

2020 ◽  
Vol 157 ◽  
pp. 828-839 ◽  
Author(s):  
Hui Yong ◽  
Shihai Guo ◽  
Zeming Yuan ◽  
Yan Qi ◽  
Dongliang Zhao ◽  
...  
Keyword(s):  
Hydrogen Storage ◽  
Catalytic Effect ◽  
Hydrogen Storage Alloy ◽  
Thermodynamics And Kinetics ◽  
Kinetics Of

Wood-Polymer Composite Prepared by In Situ Synthesis of Copolymer within Wood and its Dimensional Stability

2010 ◽  
Vol 150-151 ◽  
pp. 1-5
Author(s):  
Yong Feng Li ◽  
Chi Jiang ◽  
Duo Jun Lv ◽  
Xiao Ying Dong ◽  
Yi Xing Liu
Keyword(s):  
Contact Angle ◽  
Porous Structure ◽  
Polymer Composite ◽  
Dimensional Stability ◽  
Value Added ◽  
Hydroxyl Groups ◽  
Wood Polymer ◽  
Volume Swelling ◽  
Wood Polymer Composite

In order to improve the value-added applications of low-quality wood, a novel Wood-Polymer Composite was fabricated by in-situ synthesis of copolymer from monomers within wood porous structure. The structure was characterized with SEM and FTIR, and its dimensional stability was also tested. The SEM observations showed that copolymer filled up wood pores and contact tightly with wood matrix, indicating strong interactions between them. FTIR analysis indicated that when the monomers copolymerized in situ wood porous structure, they also reacted with wood matrix by reaction of hydroxyl groups and ester groups, indicating chemical bond between the two phases, which is agreement with SEM observations. The volume swelling efficiency and contact angle of such composite were higher than those of wood, respectively, indicating good dimensional stability involving volume swelling efficiency and contact angle. Such composite could be potentially applied in fields of construction, traffic and indoor decoration.

Modeling of Transport During Droplet Deposition and Spreading on Smooth and Microstructured Superhydrophilic Surfaces

2016 ◽  
Author(s):  
Jordan P. Mizerak ◽  
Van P. Carey
Keyword(s):  
Contact Angle ◽  
Contact Angles ◽  
Ansys Fluent ◽  
Effective Contact ◽  
Microstructured Surfaces ◽  
Static Contact ◽  
Droplet Behavior ◽  
Contact Line Pinning ◽  
The Impact ◽  
Superhydrophilic Surfaces

The dynamic behavior of impinging water droplets is studied in the context of varying surface morphologies on smooth and microstructured superhydrophilic surfaces. The goal of this study is to evaluate the capability of contact angle wall adhesion models to accurately produce spreading phenomena seen on a variety of surface types. We analyze macroscale droplet behavior, specifically spreading extent and impinging regime, in situations of varying microscale wetting character and surface morphology. Axisymmetric, volume of fluid (VOF) simulations with static contact angle wall adhesion are conducted in ANSYS Fluent. Simulations are performed on water for low Weber numbers (We<20) on surfaces with features of length scale 5–10μm. Advanced microstructured surfaces consisting of unique wetting characteristics and lengths on each face are also tested. Results show that while the contact angle wall adhesion model shows fair agreement for conventional surfaces, the model underestimates spreading by over 60% for surfaces exhibiting estimated contact angles below approximately 0.5°. Microstructured surfaces adapt the wetting behavior of smooth surfaces with higher effective contact angles based on contact line pinning on morphology features. The propensity of the model to produce Wenzel and Cassie-Baxter states is linked to the spreading radius, introducing an interdependency of microscale wetting and macroscale spreading behavior. Conclusions describing the impact of results on evaporative cooling are also discussed.

Sign in / Sign up

Export Citation Format

Share Document