scholarly journals Determination of ballistic properties on ARMOX 500T steel welded joint

2019 ◽  
Vol 39 (2) ◽  
pp. 186-196 ◽  
Author(s):  
Ivica Garašić ◽  
Maja Jurica ◽  
Ante Barišić ◽  
Dario Iljkić
Keyword(s):  
Mechanical Properties ◽  
Impact Energy ◽  
Welded Joint ◽  
Base Material ◽  
Filler Materials ◽  
Hardness Testing ◽  
Ballistic Performance ◽  
Ballistic Properties ◽  
The Impact

In this paper, the effect of different hardness filler materials and sequence of welding on the ballistic performance has been investigated. Also, besides the optimization of the ballistic properties, other mechanical testing was carried out in order to achieve wanted mechanical properties along the entire welded joint. The experimental work includes macrostructure analysis, ballistic testing, and hardness testing of steel welded joint. The base material used in the experiment were ARMOX® 500T plates. In this experiment 3 different filler materials were used. Based on the testing results, it was found out that best ballistic performance of the welded joint is achieved if capping layer is welded with a hardfacing filler material. This distributes the impact energy to a greater area and transfers it to the lower hardness weld layer underneath which then absorbs the rest of the energy.

scholarly journals Microstructure and Mechanical Properties of Heat-Affected Zone of Repeated Welding AISI 304N Austenitic Stainless Steel by Gleeble Simulator

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 773
Author(s):  
Y.H. Guo ◽  
Li Lin ◽  
Donghui Zhang ◽  
Lili Liu ◽  
M.K. Lei
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Impact Energy ◽  
Heat Affected Zone ◽  
Ferrite Content ◽  
Equipment Safety ◽  
Microstructure And Mechanical Properties ◽  
Δ Ferrite ◽  
The Impact

Heat-affected zone (HAZ) of welding joints critical to the equipment safety service are commonly repeatedly welded in industries. Thus, the effects of repeated welding up to six times on the microstructure and mechanical properties of HAZ for AISI 304N austenitic stainless steel specimens were investigated by a Gleeble simulator. The temperature field of HAZ was measured by in situ thermocouples. The as-welded and one to five times repeated welding were assigned as-welded (AW) and repeated welding 1–5 times (RW1–RW5), respectively. The austenitic matrices with the δ-ferrite were observed in all specimens by the metallography. The δ-ferrite content was also determined using magnetic and metallography methods. The δ-ferrite had a lathy structure with a content of 0.69–3.13 vol.%. The austenitic grains were equiaxial with an average size of 41.4–47.3 μm. The ultimate tensile strength (UTS) and yield strength (YS) mainly depended on the δ-ferrite content; otherwise, the impact energy mainly depended on both the austenitic grain size and the δ-ferrite content. The UTS of the RW1–RW3 specimens was above 550 MPa following the American Society of Mechanical Engineers (ASME) standard. The impact energy of all specimens was higher than that in ASME standard at about 56 J. The repeated welding up to three times could still meet the requirements for strength and toughness of welding specifications.

scholarly journals Microstructure and Mechanical Properties of Modern 11%Cr Heat-Resistant Steel Weld Joints

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3430
Author(s):  
Grzegorz Golański ◽  
Jacek Słania ◽  
Marek Sroka ◽  
Paweł Wieczorek ◽  
Michał Urzynicok ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Welded Joints ◽  
Martensitic Steel ◽  
Base Material ◽  
Hardness Measurement ◽  
Power Industry ◽  
Strength Properties ◽  
Typical Structure ◽  
Δ Ferrite ◽  
The Impact

In addition to good high-temperature creep resistance and adequate heat resistance, steels for the power industry must have, among other things, good weldability. Weldability of such steels is one of the criteria determining whether or not the material is suitable for applications in the power industry. Therefore, when materials such as martensitic steel Thor 115 (T115) are introduced into the modern power industry, the quality and properties of welded joints must be assessed. The paper presents the results of metallographic and mechanical investigations of T115 martensitic steel welded joints. The analysis was carried out on joints welded with two filler metals: WCrMo91 (No. 1) and EPRI P87 (No. 2). The scope of the investigations included: microstructural investigations carried out using optical, scanning and transmission electron microscopy and mechanical testing, i.e., Vickers microhardness and hardness measurement, static tensile test and impact test. The macro- and microstructural investigations revealed correct structure of the weld, without welding imperfections. The microstructural investigations of joint No. 1 revealed a typical structure of this type of joint, i.e., the martensitic structure with numerous precipitates, while in joint No. 2, the so-called Nernst’s layers and δ-ferrite patches were observed in the weld fusion zone as well as the heat affected zone (HAZ). The mechanical properties of the test joints met the requirements for the base material. A slight influence of the δ-ferrite patch on the strength properties of joint No. 2 was observed, and its negative effect on the impact energy of HAZ was visible.

Investigation on Impact Energy of S30403 Austenitic Stainless Steel at Different Temperatures

2016 ◽  
Vol 138 (3) ◽  
Author(s):  
Zhiwei Chen ◽  
Caifu Qian ◽  
Guoyi Yang ◽  
Xiang Li
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Cross Section ◽  
Test Temperature ◽  
Impact Energy ◽  
Welded Joint ◽  
Charpy Impact ◽  
Base Plate ◽  
Charpy Impact Energy ◽  
The Impact

In this paper, a series of impact tests on S30403 austenitic stainless steel at 20/−196/−269 °C were performed to determine the effects of cryogenic temperatures on the material properties. Both base plate and welded joint including weld and heat-affected zone were tested to obtain the Charpy impact energy KV2 and lateral expansion rate at the cross section. It was found that when the test temperature decreased from 20 °C to −196 °C or −269 °C, both the Charpy impact energy KV2 at the base plate and welded joint decreased drastically. Specifically, the impact energy KV2 decreased by 20% at the base plate and decreased by 54% at the welded joint from 20 °C to −196 °C, but the impact energy of base plate and welded joint did not decrease, even increased when test temperature decreased from −196 °C to −269 °C. Either at 20 °C or −196 °C, the impact energy KV2 with 5 × 10 × 55 mm3 specimens was about 0.53 times that of the 7.5 × 10 × 55 mm3 specimens, much lower than 2/3, the ratio of two specimens’ cross section areas.

Effect of Tempering Time on Microstructure and Mechanical Properties of SA738 Gr.B Steel

2021 ◽  
Vol 1016 ◽  
pp. 1739-1746
Author(s):  
Yan Mei Li ◽  
Shu Zhan Zhang ◽  
Zai Wei Jiang ◽  
Sheng Yu ◽  
Qi Bin Ye ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Yield Strength ◽  
Microstructure Evolution ◽  
Impact Energy ◽  
Nuclear Power ◽  
Microstructure And Mechanical Properties ◽  
The Impact ◽  
Tempering Time

The effect of tempering time on the microstructure and mechanical properties of SA738 Gr.B nuclear power steel was studied using SEM, TEM and thermodynamic software, and its precipitation and microstructure evolution during tempering were clarified. The results showed that SA738 Gr.B nuclear power steel has better comprehensive mechanical properties after tempering at 650 °C for 1h. With the extension of the tempering time, M3C transformed into M23C6 with increasing size, which affected the yield strength and impact energy. When the tempering time is 8h ~ 10h, due to the transformation of M3C to M23C6, the composition of matrix around the carbide changed, causing the temperature of Ac1 dropped, forming twin-martensite which deteriorated the impact toughness of the steel.

Study on Weldablity of Dissimilar Steel between 16MnR and S31803

2011 ◽  
Vol 391-392 ◽  
pp. 768-772 ◽  
Author(s):  
Li Yang ◽  
Zhan Zhe Zhang
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Impact Toughness ◽  
Weld Metal ◽  
Welded Joint ◽  
Optical Microscope ◽  
Dissimilar Steel ◽  
Austenite Content ◽  
Mechanical Properties And Corrosion ◽  
The Impact

The weldablity of dissimilar steel between 16MnR and S31803 was analyzed and researched. By means of optical microscope (OM), the microstructure of the weld joint was investigated, which is welded by tungsten inert gas arc backing welding (GTAW) and manual arc filling welding (SMAW). The mechanical properties and corrosion resistance of the welded joint was also tested and studied. Results indicate that austenite and acicular ferrite distribute uniformly in the weld metal, which strengths the toughness and ductility of the joint. The austenite content in weld is higher than that in over-heated zone of S31803.The SMAW joint structure is coarsening than that of GTAW and has more austenite content. It is also observed that there are a decarburization layer and a carbon-enriched zone nearby the fusion line. And very small amounts of the third phase of harmful metal phase are found in the fusion zone of S31803 side. The welded joint shows the excellent mechanical properties and corrosion resistance. The impact toughness of the weld metal is higher than in HAZ of 16MnR side, and the impact toughness at GTAW side and in HAZ is superior to the SMAW side.

MECHANICAL PROPERTIES AND SURFACE FREE ENERGY OF OIL PALM EMPTY FRUIT BUNCHES FIBRE REINFORCED BIOCOMPOSITES AS GLASS FIBRE SUBSTITUTION

2017 ◽  
Vol 79 (4) ◽  
Author(s):  
Gema Sukmawati Suryadi ◽  
Siti Nikmatin ◽  
Sudaryanto Sudaryanto ◽  
Irmansyah Irmansyah
Keyword(s):  
Mechanical Properties ◽  
Free Energy ◽  
Impact Strength ◽  
Surface Free Energy ◽  
Glass Fibre ◽  
Oil Palm ◽  
Short Fibre ◽  
Filler Materials ◽  
Empty Fruit Bunches ◽  
The Impact

Study of the size effect of natural fibre from oil palm empty fruit bunches (OPEFB) as filler, onto the mechanical and physical properties of fibre reinforced biocomposites based on recycled Acrylonitrile Butadiene Styrene (ABS) has been done. The OPEFB fibres were prepared by mechanical milling and sieving to obtain medium-fibre (20 mesh) and short-fibre (100 mesh). The biocomposites have been produced by extrusion using single-screw extruder method. Mechanical properties and S of biocomposites were evaluated and compared with glass fibre (GF) filled composite which is commonly used in plastics industrial applications. The result showed that the impact strength increased with the decreasing of OPEFB fibre size, while the Young’s modulus decreased. Other mechanical properties of biocomposites with short-fibre (RABS/SF) and medium-fibre (RABS/MF) filler were not significantly different at 95% confidence interval. Impact strength of short-fibre filled biocomposite was higher than glass fibre filled composites. The surface free energy of biocomposites lower than glass fibre filled composites, but its dispersive components are higher, indicating more hydrophobic feature of the surface. The fabricated micro-fibre of OPEFB can be used as viable alternative to substitute glass fibre as filler materials of composites.

Experimental Research and Analysis of Non-alloy Structural Steel Response Exposed to High Temperature Conditions

2013 ◽  
Vol 32 (2) ◽  
pp. 163-169
Author(s):  
Josip Brnic ◽  
Goran Turkalj ◽  
Sanjin Krscanski
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Structural Steel ◽  
Impact Energy ◽  
Charpy Impact ◽  
Experimental Results ◽  
Charpy Impact Energy ◽  
Over Time

AbstractThis paper presents and analyzes the responses of non-alloy structural steel (1.0044) subjected to uniaxial stresses at high temperatures. This research has two important determinants. The first one is determination of stress-strain dependence and the second is monitoring the behavior of materials subjected to a constant stress at constant temperature over time. Experimental results refer to mechanical properties, elastic modulus, total elongations, creep resistance and Charpy V-notch impact energy. Experimental results show that the tensile strength and yield strength of the considered material fall when the temperature rises over 523 K. Significant decrease in value is especially noticeable when the temperature rises over 723 K. In addition, engineering assessment of fracture toughness was made on the basis of Charpy impact energy. It is visible that when temperature raises then impact energy increases very slightly.

scholarly journals Degradation of Roller-Compacted Concrete Subjected to Freeze-Thaw Cycles and Immersion in Potassium Acetate Solution

2018 ◽  
Vol 2018 ◽  
pp. 1-8
Author(s):  
Wuman Zhang ◽  
Jingsong Zhang ◽  
Shuhang Chen ◽  
Sheng Gong
Keyword(s):  
Mechanical Properties ◽  
Weight Loss ◽  
Compressive Strength ◽  
Impact Energy ◽  
Impact Test ◽  
Potassium Acetate ◽  
Acetate Solution ◽  
Freeze Thaw ◽  
Roller Compacted Concrete ◽  
The Impact

Two sets of roller-compacted concrete (RCC) samples cured for 28 days were subjected to freeze-thaw (F-T) cycles and immersion in laboratory conditions. F-T cycles in water and water-potassium acetate solution (50% by weight) were carried out and followed by the flexural impact test. The weight loss, the dynamic elastic modulus (Ed), the mechanical properties, and the residual strain of RCC were measured. The impact energy was calculated based on the final number of the impact test. The results show that the effect of F-T cycles in KAc solution on the weight loss and Ed of RCC is slight. Ed, the compressive strength, and the flexural strength of RCC with 250 F-T cycles in KAc solution decrease by 3.8%, 23%, and 36%, respectively. The content (by weight) of K+ at the same depth of RCC specimens increases with the increase of F-T cycles. The impact energy of RCC specimens subjected to 250 F-T cycles in KAc solution decreases by nearly 30%. Microcracks occur and increase with the increase of F-T cycles in KAc solution. The compressive strength of RCC immersed in KAc solution decreases by 18.8% and 32.8% after 6 and 12 months. More attention should be paid to using KAc in practical engineering because both the freeze-thaw cycles and the complete immersion in KAc solution damage the mechanical properties of RCC.

scholarly journals Effect of Alloying Composition on Microstructure and Mechanical Properties of Ultranarrow Gap Welded Joints of U71Mn Rail Steel

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Lian Gong ◽  
Hui Liu ◽  
Cheng Lv ◽  
Lijun Zhao
Keyword(s):  
Mechanical Properties ◽  
Base Metal ◽  
Welded Joints ◽  
Alloy Composition ◽  
Rail Steel ◽  
Base Material ◽  
Average Hardness ◽  
Microstructure And Mechanical Properties ◽  
Fine Pearlite ◽  
The Impact

A new welding method, ultranarrow gap welding with constrained arc by flux band, is proposed to compensate for the low quality of rail thermite welded joints. This article presents the results of research on the microstructure and mechanical properties of ultranarrow gap welded joints of U71Mn rail steel made using three types of alloying composition content flux bands. Results indicated that the base metal metallographic microstructure consisted mainly of pearlitic, the HAZ was mainly composed of fine pearlite, and the microstructure of the welded bead was composed of acicular ferrite, while the weld grain size decreased as the alloy composition increased. The average hardness noticeably changed in weld metal as the alloy composition increased, and when the alloy composition reached 19%, the hardness was equivalent to the base material. The average hardness value of the HAZ (35.8 HRC) was higher than that of the base metal (24.8 HRC). The tensile strength increased, and the percentage elongation after fracture decreased with increasing alloying composition from 9% to 19%. The impact absorbing energies were decreased as the alloying composition increased. Consequently, all the mechanical properties of rail ultranarrow gap welding were higher than those of the standard requirements of the rail flash welding. And the optimal alloying composition of flux band was 19%.

Influence of Proposed Hardening Process on Hardness and Toughness of Martensitic Stainless Steel

2017 ◽  
Vol 750 ◽  
pp. 103-106
Author(s):  
Charnnarong Saikaew ◽  
Worakarn Sawatwor
Keyword(s):  
Mechanical Properties ◽  
Impact Energy ◽  
Heat Treating ◽  
Time Range ◽  
Soaking Time ◽  
Heat Treated ◽  
Quench Temperature ◽  
Four Levels ◽  
Level Of Significance ◽  
The Impact

Many researchers have studied the effects of heat treating processes on mechanical properties, corrosion and wear resistance of various martensitic stainless steels. It is crucial to comprehensively understand the role of heat treating processes on the mechanical properties of the steels with a systematic approach. In this work, the specimens were heat treated by preheating in two steps before continuing the heating to the quench temperature. The first preheating was performed in the furnace maintained at 400 °C for 5 min. The second step was done in the furnace kept at 800 °C for 5 min. Then the specimens were heated directly to the hardening temperature, 1030 °C. The specimens reached 1030 °C for a sufficient time of 30 min to form austenite and to allow enough of the carbides to be dissolved to ensure the desired combination of hardness and toughness. After hardening time was over, the specimens were quenched in water to form martensite for 2-8 s and holding in the air for 4 s, followed with water quenching for 2-8 s and cooling to room temperature. Data was collected in order to perform one-way analysis of variance (ANOVA). In this study, the ANOVA consisted of four levels of soaking time of 2, 4, 6 and 8 s and holding time of 4 s. All heat-treated specimens were then used to perform hardness and Charpy-V-Notch impact tests. The results showed that the hardness values increased with increasing of soaking time. The impact energy value slightly decreased with the soaking time range of 2-4 s whereas it rapidly decreased with the soaking time range of 4-6 s and slightly increased with the range of 6-8 s. However, the results from ANOVA showed that the soaking time did not significantly affect the averages hardness and impact energy at the level of significance of 0.05.

Sign in / Sign up

Export Citation Format

Share Document