EXTRACTABILITY OF HEAVY METALS IN BOTTOM ASH FROM A MEDIUM-SIZE (32 MW) MUNICIPAL DISTRICT HEATING PLANT BY ARTIFICIAL SWEAT AND GASTRIC FLUIDS

2010 ◽  
Vol 9 (7) ◽  
pp. 909-913
Author(s):  
Risto Poykio ◽  
Hannu Nurmesniemi
Keyword(s):  
Heavy Metals ◽  
Bottom Ash ◽  
District Heating ◽  
Medium Size ◽  
Municipal District ◽  
Artificial Sweat ◽  
Gastric Fluids ◽  
Heating Plant

The fate of heavy metals and salts during the wet treatment of municipal solid waste incineration bottom ash

2021 ◽  
Vol 121 ◽  
pp. 33-41
Author(s):  
Yanjun Hu ◽  
Lingqin Zhao ◽  
Yonghao Zhu ◽  
Bennong Zhang ◽  
Guixiang Hu ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Municipal Solid Waste ◽  
Solid Waste ◽  
Bottom Ash ◽  
Waste Incineration ◽  
Municipal Solid Waste Incineration

Determination of Residual Heavy Metals in an Incinerator Bottom Ash from Municipal Solid Waste Power Plant

2020 ◽  
Vol 901 ◽  
pp. 65-71
Author(s):  
Woravith Chansuvarn
Keyword(s):  
Heavy Metals ◽  
Power Plant ◽  
Municipal Solid Waste ◽  
Solid Waste ◽  
Microwave Digestion ◽  
Bottom Ash ◽  
Flame Atomic Absorption ◽  
Digestion Technique ◽  
Relative Standard ◽  
Copper Zinc

Bottom ash is a part of by-product from the municipal solid waste power plants which is always a wider problem for the urban and rural communities due to its disposal plants may cause serious environmental pollution. This work was focused on the residual heavy metal in an incinerator bottom ash from the municipal waste power plant placed in Nongkham district, Bangkok. Four bottom ash samples were obtained in 2017. After drying and grounding, the bottom ash samples were prepared to clear solution with the microwave digestion technique using nitric, hydrochloric and hydrofluoric acid under the heating program. The total residual heavy metals in the incinerator bottom ashes, such as lead, copper, zinc, and cadmium were determined by using flame atomic absorption spectrophotometer (FAAS) with deuterium background correction. The total concentration of lead, copper, zinc and cadmium were found in the range of 280.40-354.22mg kg-1, 365.35-524.45 mg kg-1, 1,527.25-2,074.34 mg kg-1, and 0.48-1.02 mg kg-1, respectively. The recovery of all metals was found in the range of 89.4-101.2% and the relative standard deviation (RSD) was to be 2.15-3.55 % (n=7). The concentration of zinc, copper, and lead was found high levels, while cadmium was low concentration. Heavy metals in solid waste material occur in different chemical forms and phases. The sample preparation based on the microwave digestion was successfully developed for the waste samples with a good reliability.

Precipitation of heavy metals from coal ash leachate using biogenic hydrogen sulfide generated from FGD gypsum

2013 ◽  
Vol 67 (2) ◽  
pp. 311-318 ◽  
Author(s):  
Madawala Liyanage Duminda Jayaranjan ◽  
Ajit P. Annachhatre
Keyword(s):  
Heavy Metals ◽  
Hydrogen Sulfide ◽  
Sulfate Reduction ◽  
Bottom Ash ◽  
Coal Ash ◽  
Reduction Process ◽  
Fgd Gypsum ◽  
Sulfate Reducing ◽  
Sulfate Reduction Process ◽  
Biological Sulfate Reduction

Investigations were undertaken to utilize flue gas desulfurization (FGD) gypsum for the treatment of leachate from the coal ash (CA) dump sites. Bench-scale investigations consisted of three main steps namely hydrogen sulfide (H2S) production by sulfate reducing bacteria (SRB) using sulfate from solubilized FGD gypsum as the electron acceptor, followed by leaching of heavy metals (HMs) from coal bottom ash (CBA) and subsequent precipitation of HMs using biologically produced sulfide. Leaching tests of CBA carried out at acidic pH revealed the existence of several HMs such as Cd, Cr, Hg, Pb, Mn, Cu, Ni and Zn. Molasses was used as the electron donor for the biological sulfate reduction (BSR) process which produced sulfide rich effluent with concentration up to 150 mg/L. Sulfide rich effluent from the sulfate reduction process was used to precipitate HMs as metal sulfides from CBA leachate. HM removal in the range from 40 to 100% was obtained through sulfide precipitation.

Sign in / Sign up

Export Citation Format

Share Document