scholarly journals Evaluation through finite element and numerical simulation of triboelectric polymer pairs in vertical contact mode

2021 ◽  
pp. 35-45
Author(s):  
Shimna SHAFEEK ◽  
Sibgatulla SHARİEEF
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Contact Mode ◽  
Vertical Contact

Numerical Simulation of Tire Sliding Events Involving Impacts with Holes and Bumps

1986 ◽  
Vol 14 (2) ◽  
pp. 125-136 ◽  
Author(s):  
Y. Nakajima ◽  
J. Padovan
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Finite Element Simulation ◽  
Full Range ◽  
Arbitrary Geometry ◽  
Operating Environments ◽  
Element Simulation ◽  
Simulation Scheme

Abstract This paper extends the finite element simulation scheme to handle the problem of tires undergoing sliding (skidding) impact into obstructions. Since the inertial characteristics are handled by the algorithm developed, the full range of operating environments can be accommodated. This includes the treatment of impacts with holes and bumps of arbitrary geometry.

The study of the elastic deformation of a flexible wheel by a cam wave generator

2020 ◽  
Vol 65 (1) ◽  
pp. 51-58
Author(s):  
Sava Ianici
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Elastic Deformation ◽  
Theoretical Study ◽  
Elastic Field ◽  
The Finite Element Method ◽  
Elastic Deformations ◽  
Wave Generator ◽  
Two Stages

The paper presents the results of research on the study of the elastic deformation of a flexible wheel from a double harmonic transmission, under the action of a cam wave generator. Knowing exactly how the flexible wheel is deformed is important in correctly establishing the geometric parameters of the wheels teeth, allowing a better understanding and appreciation of the specific conditions of harmonic gearings in the two stages of the transmission. The veracity of the results of this theoretical study on the calculation of elastic deformations and displacements of points located on the average fiber of the flexible wheel was subsequently verified and confirmed by numerical simulation of the flexible wheel, in the elastic field, using the finite element method from SolidWorks Simulation.

Hot Compression Simulation of Ti75 Alloy Based on DEFORM-3D

2012 ◽  
Vol 229-231 ◽  
pp. 55-58
Author(s):  
Jun Fan
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Simulation Method ◽  
Hot Compression ◽  
Strain Rates ◽  
Know How ◽  
Numerical Simulation Method ◽  
Control Objective ◽  
Finite Element Numerical Simulation ◽  
Deform 3D

To obtain the know-how of the deficiency for the filling capability, taking Ti75 alloy as the research object, at the same height of reducing, strain rates during forming as the control objective, the finite element numerical simulation method was used to simulate the hot compression with DEFORM-3D, analyzing the effect of the strain rates on the distribution of strain and stress.

Numerical Simulation of the Effects of Preheating on Electron Beam Additive Manufactured Ti-6Al-4V Build Plate

2016 ◽  
Vol 879 ◽  
pp. 274-278 ◽  
Author(s):  
Jun Cao ◽  
Philip Nash
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Finite Element ◽  
Electron Beam ◽  
Cross Section ◽  
Element Model ◽  
Normal Direction ◽  
Thermal Residual Stresses ◽  
Longitudinal Residual Stress ◽  
Middle Cross Section

In an earlier study, a 3-D thermomechanical coupled finite element model was built and experimentally validated to investigate the evolution of the thermal residual stresses and distortions in electron beam additive manufactured Ti-6Al-4V build plates. In this study, an investigation using this robust and accurate model was focused on an efficient preheating method, in which the electron beam quickly scanned across the substrate to preheat the build plate prior to the deposition. Various preheat times, beam powers, scan rates, scanning paths and cooling times (between the end of current preheat scan/deposition layer and the beginning of the next preheat scan/deposition layer) were examined, and the maximum distortion along the centerline of the substrate and the maximum longitudinal residual stress along the normal direction on the middle cross-section of the build plate were quantitatively compared. The results show that increasing preheat times and beam powers could effectively reduce both distortion and residual stress for multiple layers/passes components.

Multi-Step Forward Finite Element Method for the Numerical Simulation of Sheet Metal Forming

2011 ◽  
Vol 474-476 ◽  
pp. 251-254
Author(s):  
Jian Jun Wu ◽  
Wei Liu ◽  
Yu Jing Zhao
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Deep Drawing ◽  
Metal Forming ◽  
Mapping Method ◽  
Constitutive Relationship ◽  
Element Method

The multi-step forward finite element method is presented for the numerical simulation of multi-step sheet metal forming. The traditional constitutive relationship is modified according to the multi-step forming processes, and double spreading plane based mapping method is used to obtain the initial solutions of the intermediate configurations. To verify the multi-step forward FEM, the two-step simulation of a stepped box deep-drawing part is carried out as it is in the experiment. The comparison with the results of the incremental FEM and test shows that the multi-step forward FEM is efficient for the numerical simulation of multi-step sheet metal forming processes.

Sign in / Sign up

Export Citation Format

Share Document