scholarly journals Heat Simulation of High-speed Train’s Brake Disc Considering the Wind Speed of Disc Surface Influence on Convection Coefficient

2012 ◽  
Author(s):  
Xiaobiao Wu ◽  
Jianyong Zuo ◽  
Mengling Wu
Keyword(s):  
Wind Speed ◽  
High Speed ◽  
Brake Disc ◽  
Convection Coefficient ◽  
Disc Surface ◽  
Heat Simulation

Tribological and dynamical analysis of a brake pad with multiple blocks for a high-speed train

2019 ◽  
Vol 234 (11) ◽  
pp. 1771-1788
Author(s):  
YK Wu ◽  
JL Mo ◽  
B Tang ◽  
JW Xu ◽  
B Huang ◽  
...  
Keyword(s):  
High Speed ◽  
Wear Behavior ◽  
Dynamical Analysis ◽  
Brake Disc ◽  
Brake Pad ◽  
High Speed Train ◽  
Brake Squeal ◽  
Element Analysis ◽  
Single Block ◽  
Middle Ring

In this research, the tribological and dynamical characteristics of a brake pad with multiple blocks are investigated using experimental and numerical methods. A dynamometer with a multiblock brake pad configuration on a brake disc is developed and a series of drag-type tests are conducted to study the brake squeal and wear behavior of a high-speed train brake system. Finite element analysis is performed to derive physical explanations for the observed experimental phenomena. The experimental and numerical results show that the rotational speed and braking force have important influences on the brake squeal; the trends of the multiblock and single-block systems are different. In the multiblock brake pad, the different blocks exhibit significantly different magnitudes of contact stresses and vibration accelerations. The blocks located in the inner and outer rings have higher vibration acceleration amplitudes and stronger vibration energies than the blocks located in the middle ring.

Numerical Modeling and Simulation Analysis of Temperature Field of Disc Brake on Trains

2011 ◽  
Vol 199-200 ◽  
pp. 1492-1495 ◽  
Author(s):  
Guo Shun Wang ◽  
Rong Fu ◽  
Liang Zhao
Keyword(s):  
Temperature Field ◽  
Temperature Gradient ◽  
High Speed ◽  
Large Scale ◽  
Working Condition ◽  
Constant Speed ◽  
Brake Disc ◽  
Disc Brake ◽  
Brake Pad ◽  
Finite Element Software

The simulation calculation on the temperature field of the disc brake system on high-speed trains under the working condition of constant speed at 50Km/h is made. A steady-state calculation model is established according to the actual geometric size of a brake disc and a brake pad, and the analog calculation and simulation on the temperature field of the brake disc and the brake pad by using the large-scale nonlinear finite element software ABAQUS are carried out. The distribution rules of the temperature field of the brake disc and the brake pad under the working condition of constant speed are made known. The surface temperature of the brake disc at friction radius is the highest, with a band distribution for temperature. There exists a temperature flex point in the direction of thickness, of which the thickness occupies 15% of that of the brake disc; due to the small volume of the brake pad, the temperature gradient of the whole brake pad is not sharp, and larger temperature gradient occurs only on the contact surface.

Design and performance evaluation of vertical axis wind turbine for wind energy harvesting at railway

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Hashwini Lalchand Thadani ◽  
Fadia Dyni Zaaba ◽  
Muhammad Raimi Mohammad Shahrizal ◽  
Arjun Singh Jaj A. Jaspal Singh Jaj ◽  
Yun Ii Go
Keyword(s):  
Wind Speed ◽  
Energy Harvesting ◽  
Wind Energy ◽  
Wind Turbine ◽  
High Speed ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Modeling Tools ◽  
Content Type

PurposeThis paper aims to design an optimum vertical axis wind turbine (VAWT) and assess its techno-economic performance for wind energy harvesting at high-speed railway in Malaysia.Design/methodology/approachThis project adopted AutoCAD and ANSYS modeling tools to design and optimize the blade of the turbine. The site selected has a railway of 30 km with six stops. The vertical turbines are placed 1 m apart from each other considering the optimum tip speed ratio. The power produced and net present value had been analyzed to evaluate its techno-economic viability.FindingsComputational fluid dynamics (CFD) analysis of National Advisory Committee for Aeronautics (NACA) 0020 blade has been carried out. For a turbine with wind speed of 50 m/s and swept area of 8 m2, the power generated is 245 kW. For eight trains that operate for 19 h/day with an interval of 30 min in nonpeak hours and 15 min in peak hours, total energy generated is 66 MWh/day. The average cost saved by the train stations is RM 16.7 mil/year with battery charging capacity of 12 h/day.Originality/valueWind energy harvesting is not commonly used in Malaysia due to its low wind speed ranging from 1.5 to 4.5 m/s. Conventional wind turbine requires a minimum cut-in wind speed of 11 m/s to overcome the inertia and starts generating power. Hence, this paper proposes an optimum design of VAWT to harvest an unconventional untapped wind sources from railway. The research finding complements the alternate energy harvesting technologies which can serve as reference for countries which experienced similar geographic constraints.

scholarly journals Intermittent Gliding in the Hunting Flight of the Kestrel, Falco Tinnunculus L

1983 ◽  
Vol 102 (1) ◽  
pp. 1-12 ◽  
Author(s):  
J. J. VIDELER ◽  
D. WEIHS ◽  
S. DAAN
Keyword(s):  
Theoretical Model ◽  
Wind Speed ◽  
High Speed ◽  
Flapping Flight ◽  
Falco Tinnunculus ◽  
Fixed Position ◽  
Centre Of Gravity ◽  
High Speed Film

The hunting flight of the kestrel (Falco tinnunculus) consists of short bouts of flight at wind speed against the wind with the eyes in a fixed position relative to the ground, and of short flights from one such position to the next. High speed films taken with a camera in a fixed position of a hunting kestrel of known weight and dimensions, allow estimates to be made of the amount of energy required for this behaviour. A theoretical model shows how a bird could economise by alternating flapping flight with short gliding bouts, without changing the position of the eyes above the ground, by mere displacement of the centre of gravity relative to the head. High speed film data confirm predictions from this model.

scholarly journals Numerical studies on aerodynamics of high-speed railway train subjected to strong crosswind

2019 ◽  
Vol 11 (11) ◽  
pp. 168781401988727
Author(s):  
Xu Wang ◽  
Yuanhao Qian ◽  
Zengshun Chen ◽  
Xiao Zhou ◽  
Huaqiang Li ◽  
...  
Keyword(s):  
Wind Speed ◽  
High Speed ◽  
Lift Coefficient ◽  
Aerodynamic Characteristics ◽  
Width Ratio ◽  
Force Coefficient ◽  
Rolling Moment ◽  
Side Force ◽  
Train Speed ◽  
Yaw Angle

Under the action of strong crosswind, the aerodynamic behavior of a rail vehicle at high speed will be changed significantly, which could directly affect the safe operation of the vehicle. With the help of the shape of train used in China, the aerodynamic characteristics of trains with scale of 1:1 is investigated using computational fluid dynamics numerical simulation method, which consists of the variation of aerodynamics force and moment with wind yaw angle, wind speed, train speed, and nose shape. After an initial validation against Baker’s results from wind tunnel test, the numerical model is then used to investigate the aerodynamic characteristics of the trains. The numerical results indicate that lift coefficient of the M train is slightly higher than TMC1 and TMC2 trains. Regardless of aerodynamics force coefficients, TMC1 reaches the maximum at a yaw angle of 75°. Aerodynamics force coefficient increases with both wind speed and train speed, but the change of which is not linear. Comparing aerodynamic force with different geometric dimensions of train nose, it is shown that height–width ratio is insensitive to side force and rolling moment, but sensitive to lift force from the yaw angle 0°–90°. The side force coefficient, as we most concern, is less than other results, when the length–width ratio is 1 and height–width is 0.87.

scholarly journals Thermomechanical Fatigue Behavior of Spray-Deposited SiCp/Al-Si Composite Applied in the High-Speed Railway Brake Disc

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Wei Li ◽  
Huitao Chen ◽  
Lu Zuo ◽  
Jian Chen ◽  
Dongliang Xu ◽  
...  
Keyword(s):  
High Speed ◽  
Stress Amplitude ◽  
Fatigue Behavior ◽  
Phase Interface ◽  
Thermomechanical Fatigue ◽  
Brake Disc ◽  
Dislocation Generation ◽  
Si Content ◽  
Al Matrix ◽  
Sic Particle

The thermomechanical fatigue (TMF) behaviors of spray-deposited SiCp-reinforced Al-Si alloy were investigated in terms of the size of Si particles and the Si content. Thermomechanical fatigue experiments were conducted in the temperature range of 150-400°C. The cyclic response behavior indicated that the continuous cyclic softening was exhibited for all materials, and the increase in SiC particles size and Si content aggravated the softening degree, which was attributed to dislocation generation due to differential thermal contraction at the Al matrix/Si phase interface or Al matrix/SiC particle interface. Meanwhile, the TMF life and stress amplitude of SiCp/Al-7Si composites were greater than those of Al-7Si alloy, and increased with the increasing SiC particle size, which was associated with “load sharing” of the direct strengthening mechanism. The stress amplitude of 4.5μmSiCp/Al-Si composite increased as the Si content increased; however, the influence of Si content on the TMF life was not so significant. The TMF failure mechanism revealed that the crack mainly initiated at the agglomeration of small-particulate SiC and the breakage of large-particulate SiC, and the broken primary Si and the exfoliated eutectic Si accelerated the crack propagation.

Sign in / Sign up

Export Citation Format

Share Document