scholarly journals Evaluation of Hydrogen-Assisted Cracking Susceptibility in Grade T24 Steel

2020 ◽  
Vol 99 (4) ◽  
pp. 101s-109s
Author(s):  
XIULI FENG ◽  
◽  
JOSEPH M. STEINER ◽  
BOIAN T. ALEXANDROV ◽  
JOHN C. LIPPOLD
Keyword(s):  
Base Metal ◽  
Heat Affected Zone ◽  
Fracture Behavior ◽  
Coarse Grained ◽  
Internal Diameter ◽  
Microvoid Coalescence ◽  
Martensitic Microstructure ◽  
Steel Base ◽  
Hydrogen Assisted Cracking ◽  
Martensite Microstructure

The delayed hydrogen cracking test was performed to evaluate the hydrogen-assisted cracking (HAC) susceptibility of Grade T24 steel base metal and the simulated coarse-grained heat-affected zone (CGHAZ). The base metal did not fail after testing for up to 672 h. In contrast, the CGHAZ sample failed after about 2 h when charged from all four sides, and 4 h when charged only from the internal diameter (ID) surface. The higher HAC resistance of the base metal compared to the CGHAZ was due to the microstructure difference. The tempered bainitic-martensitic microstructure in the base metal was more resistant to HAC compared to the untempered martensite microstructure in the CGHAZ. Fractography analysis indicated the decarburized zone on the ID surface delayed the development of the critical hydrogen concentration in the CGHAZ, thus improving the HAC resistance. The HAC cracking initiated with an intergranular fracture, then transitioned to quasi-cleavage and microvoid coalescence. The fracture behavior was explained using Beachem’s model.

FE Simulation of Cold Cracking Susceptibility in X70 Structural Steel Welded Joints

2011 ◽  
Author(s):  
Vigdis Olden ◽  
Odd Magne Akselsen
Keyword(s):  
Hydrogen Embrittlement ◽  
Yield Strength ◽  
Structural Steel ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welded Joints ◽  
Fe Simulation ◽  
Coarse Grained ◽  
Best Fitting ◽  
Low Sensitivity

Fracture mechanics SENT testing and FE simulation to establish hydrogen influenced cohesive parameters for X70 structural steel welded joints have been performed. Base metal and weld simulated coarse grained heat affected zone have been included in the study. The base metal did not fail at net section stresses lower than 1.29 times the yield strength and reveals low sensitivity to hydrogen embrittlement. The weld simulated coarse grained heat affected zone was prone to fracture at stresses above 64% of the yield strength, which indicates hydrogen embrittlement susceptibility. The cohesive parameters best fitting the experiments are δc = 0.3 mm and σc = 1700 MPa (3.5·σy) for the base metal and δc = 0.3 mm and σc = 2100 MPa (2.6·σy) for the coarse grained heat affected zone.

Region-Specified Ratcheting Behavior of API X80 Welded Joint Under Uniaxial Cyclic Loading

2016 ◽  
Author(s):  
Hongsheng Lu ◽  
Yonghe Yang ◽  
Gang Chen ◽  
Xu Chen ◽  
Xin Wang
Keyword(s):  
Weld Metal ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welded Joint ◽  
Pipeline Steel ◽  
Coarse Grained ◽  
Strain Accumulation ◽  
Lower Strength ◽  
Fine Grained ◽  
Ratcheting Strain

Evaluation of mechanical performance of different regions can be difficult by using standard size samples due to the size limitation of weld metal and heat-affected zone (HAZ). At first, the microstructure of different regions was characterized and quantified by Scanning Electron Microscope, which indicate that the pipeline steel is a typical acicular ferrite steel. In this study the deformation behavior of different regions (base metal, weld metal and heat affected zone) in a welded joint of API X80 pipeline steel were studied by conducting uniaxial loading tests on miniature specimens with the cross section of 2×0.5mm and gauge length of 9mm. From the results of uniaxial tension in base metal and weld metal it is shown that the welding is overmatching. Compared to the base metal, the coarse grained HAZ exhibits a lower strength, while the fine grained HAZ exhibits a higher strength. Under near zero-to-tension cyclic stress loading, all regions of the welded joints exhibit progressive accumulation of plastic strain. Under the same stress level, the base metal shows the fastest ratcheting strain accumulation, which is the result of lower strength than other regions. This fact may indicate that the ratcheting behavior of the overall welded joint is highly dependence on that of base metal for the present case. But when under the same normalized stress level (σ = σ/σYS), the fine grained HAZ has the highest ratcheting strain accumulation, while the coarse grained HAZ has the lowest ratcheting strain accumulation, which reveals that the intrinsic resistance to ratcheting is yield strength dependent.

scholarly journals Assessment of Heat-Affected Zone Softening of Hot-Press-Formed Steel over 2.0 GPa Tensile Strength with Bead-On-Plate Laser Welding

2021 ◽  
Vol 11 (13) ◽  
pp. 5774
Author(s):  
Kwangsoo Kim ◽  
Namhyun Kang ◽  
Minjung Kang ◽  
Cheolhee Kim
Keyword(s):  
Laser Welding ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welding Process ◽  
High Strength ◽  
Hardness Test ◽  
Fracture Initiation ◽  
Hot Press ◽  
Automotive Body ◽  
Martensitic Microstructure

High-strength hot-press-formed (HPF) steels with a fully martensitic microstructure are being widely used in the fabrication of automotive body structure, and 2.0 GPa-strength HPF steel has recently been commercially launched. However, heat-affected zone (HAZ) softening is unavoidable in welding martensitic steel. In this study, the HAZ softening characteristic of 2.0 GPa HPF steel was investigated by applying a high-brightness laser welding process, wherein the heat input was controlled by varying the welding speed. Microstructural evaluation and hardness test results showed that the base metal with a fully martensitic microstructure was changed to the same type of fully martensitic microstructure in the weld metal, while relatively soft microstructures of tempered martensite and ferrite phase were partially formed in the intercritical HAZ (ICHAZ) and subcritical HAZ (SCHAZ) areas. In the tensile test, the joint strength was 10–20% lower than that of the base metal, and the fracture initiation was estimated at the ICHAZ/SCHAZ boundary, where the lowest hardness was confirmed by the nanoindentation technique.

scholarly journals Properties of a thick-section narrow-gap gas tungsten arc weld of cast Haynes 282

2021 ◽  
Author(s):  
Michael Santella ◽  
X. Frank Chen ◽  
Philip Maziasz ◽  
Jason Rausch ◽  
Jonathan Salkin
Keyword(s):  
Base Metal ◽  
Heat Affected Zone ◽  
Reference Data ◽  
Filler Metal ◽  
Stress Rupture ◽  
Narrow Gap ◽  
Weld Deposit ◽  
Gas Tungsten Arc ◽  
Gas Tungsten ◽  
Weld Heat

AbstractA 50.8-mm-deep gas tungsten arc weld was made with matching filler metal in cast Haynes 282 alloy. The narrow-gap joint was filled with 104 weld beads. Visual and dye-penetrant inspection of cross-weld specimens indicated that the cast base metal contained numerous casting defects. No visible indications of physical defects were found in the weld deposit. The weld heat-affected zone was characterized by microcracking and localized recrystallization. The cause of the cracking could not be determined. Hardness testing showed that a softened region in the as-welded heat-affected zone was nearly eliminated by post-weld heat treatment. Tensile testing up to 816 °C showed that cross-weld specimen strengths ranged from 57 to 79% of the cast base metal tensile strength. The stress-rupture strengths of cross-weld specimens are within 20% of base metal reference data. Failures of both tensile and stress-rupture specimens occurred in the base metal.

Effect of Microstructure on High-Strength Low-Alloy Steel Welded Joint Toughness with Simulation of Heat-Affected Zone Coarse-Grained Area

Metallurgist ◽  
2021 ◽  
Vol 64 (9-10) ◽  
pp. 875-884
Author(s):  
K. G. Vorkachev ◽  
P. P. Stepanov ◽  
L. I. Éfron ◽  
M. M. Kantor ◽  
A. V. Chastukhin ◽  
...  
Keyword(s):  
Alloy Steel ◽  
Heat Affected Zone ◽  
Welded Joint ◽  
High Strength ◽  
Coarse Grained ◽  
Low Alloy Steel ◽  
Effect Of Microstructure

Welding of Fe-Al Intermetallic Compound and Steel by SPS Technology

2012 ◽  
Vol 581-582 ◽  
pp. 582-585
Author(s):  
Guo Dong Zhang ◽  
Ya Dong Xiao ◽  
Nian Liu ◽  
Min Hong
Keyword(s):  
Intermetallic Compound ◽  
Base Metal ◽  
Heat Affected Zone ◽  
High Strength Steel ◽  
Chemical Potential ◽  
High Strength ◽  
Micro Hardness ◽  
Axial Pressure ◽  
Welding Joint ◽  
Short Period

The welding between Fe-Al intermetallic compound and high-strength steel was done via SPS technology. Microstructure, elements concentration and micro-hardness of welding joint were examined. The results indicated that there was no obvious welding heat-affected zone in both Fe-Al intermetallic compound and high-strength steel. The HAZ microstructures of high-strength steel were mainly martensite. In Fe-Al intermetallic compound, the grain size of heat-affected zone was larger than that of base metal and the density of heat-affected zone was lower than that of base metal. Besides, the grains of base metal had deformation phenomena. The welding joint had steady performance and the connection was reliable. Under the influence of chemical potential differences, unidirectional impulses discharge current and axial pressure, elements diffused perfectly in a short period of time.

Gas metal arc welding of XPF800 steel for automotive industry: Microstructural evaluation and mechanical properties investigation

2021 ◽  
pp. 146442072110567
Author(s):  
Emre Korkmaz ◽  
Cemal Meran
Keyword(s):  
Mechanical Properties ◽  
Base Metal ◽  
Automotive Industry ◽  
Heat Affected Zone ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
Charpy Impact ◽  
Optical Microscope ◽  
Metal Arc Welding ◽  
Heat Affected Zone Softening

In this study, the effect of gas metal arc welding on the mechanical and microstructure properties of hot-rolled XPF800 steel newly produced by TATA Steel has been investigated. This steel finds its role in the automotive industry as chassis and seating applications. The microstructure transformation during gas metal arc welding has been analyzed using scanning electron microscope, optical microscope, and energy dispersive X-ray spectrometry. Tensile, Charpy impact, and microhardness tests have been implemented to determine the mechanical properties of welded samples. Acceptable welded joints have been obtained using heat input in the range of 0.28–0.46 kJ/mm. It has been found that the base metal hardness of the welded sample is 320 HV0.1. On account of the heat-affected zone softening, the intercritical heat-affected zone hardness values have diminished ∼20% compared to base metal.

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

2018 ◽  
Vol 937 ◽  
pp. 61-67
Author(s):  
Yu Jie Li ◽  
Jin Wei Lei ◽  
Xuan Wei Lei ◽  
Oleksandr Hress ◽  
Kai Ming Wu
Keyword(s):  
Low Temperature ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
High Strength ◽  
High Heat ◽  
Coarse Grained ◽  
Low Temperature Impact Toughness ◽  
The Impact ◽  
Welding Processes

Utilizing submerged arc welding under heat input 50 kJ/cm on 60 mm thick marine engineering structure plate F550, the effect of preheating and post welding heat treatment on the microstructure and impact toughness of coarse-grained heat-affected zone (CGHAZ) has been investigated. The original microstructure of the steel plate is tempered martensite. The yield and tensile strength is 610 and 660 MPa, respectively. The impact absorbed energy at low temperature (-60 °C) at transverse direction reaches about 230~270 J. Welding results show that the preheating at 100 °C did not have obvious influence on the microstructure and toughness; whereas the tempering at 600 °C for 2.5 h after welding could significantly reduce the amount of M-A components in the coarse-grained heat-affected zone and thus improved the low temperature impact toughness.

Sign in / Sign up

Export Citation Format

Share Document