scholarly journals External heat transfer on nozzle guide vanes under highly swirled combustor outlet flow

2019 ◽  
Author(s):  
Simone Cubeda ◽  
Lorenzo Mazzei ◽  
Antonio Andreini
Keyword(s):  
Heat Transfer ◽  
External Heat ◽  
Guide Vanes ◽  
External Heat Transfer ◽  
Outlet Flow ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes

Film Cooling Research on the Endwall of a Turbine Nozzle Guide Vane in a Short Duration Annular Cascade: Part 1—Experimental Technique and Results

1992 ◽  
Vol 114 (4) ◽  
pp. 734-740 ◽  
Author(s):  
S. P. Harasgama ◽  
C. D. Burton
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
Suction Side ◽  
Coolant Temperature ◽  
Guide Vanes ◽  
Nozzle Guide ◽  
Annular Cascade ◽  
Nozzle Guide Vanes

Heat transfer and aerodynamic measurements have been made on the endwalls of an annular cascade of turbine nozzle guide vanes in the presence of film cooling. The results indicate that high levels of cooling effectiveness can be achieved on the endwalls of turbine nozzle guide vanes (NGV). The NGV were operated at the correct engine nondimensional conditions of Reynolds number, Mach number, gas-to-wall temperature ratio, and gas-to-coolant density ratio. The results show that the secondary flow and horseshoe vortex act on the coolant, which is convected toward the suction side of the NG V endwall passage. Consequently the coolant does not quite reach the pressure side/casing trailing edge, leading to diminished cooling in this region. Increasing the blowing rate from 0.52 to 1.1 results in significant reductions in heat transfer to the endwall. Similar trends are evident when the coolant temperature is reduced. Measured heat transfer rates indicate that over most of the endwall region the film cooling reduces the Nusselt number by 50 to 75 percent.

scholarly journals Endwall Heat Transfer and Aerodynamic Measurements in an Annular Cascade of Nozzle Guide Vanes

1995 ◽  
Author(s):  
M. C. Spencer ◽  
G. D. Lock ◽  
T. V. Jones ◽  
N. W. Harvey
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Reynolds Numbers ◽  
Flow Visualisation ◽  
Surface Shear ◽  
Guide Vanes ◽  
Nozzle Guide ◽  
Annular Cascade ◽  
Nozzle Guide Vanes ◽  
Transient Liquid Crystal Technique

Aerodynamic and heat transfer measurements have been made on the hub and casing endwalls of an annular cascade of high pressure nozzle guide vanes. The measurements have been made over a range of engine representative Mach and Reynolds numbers and with large levels of freestream turbulence intensity. The transient liquid crystal technique has been employed, which has the advantage of yielding full surface maps of heat transfer coefficient. Computational predictions and aerodynamic measurements of Mach number distributions on the endwall surfaces are also presented, along with surface-shear flow visualisation using oil and dye techniques. The heat transfer results are discussed and interpreted in terms of the secondary flow and Mach number patterns.

Film Cooling Research on the Endwall of a Turbine Nozzle Guide Vane in a Short Duration Annular Cascade: Part 1 — Experimental Technique and Results

1991 ◽  
Author(s):  
S. P. Harasgama ◽  
C. D. Burton
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
Suction Side ◽  
Coolant Temperature ◽  
Guide Vanes ◽  
Nozzle Guide ◽  
Annular Cascade ◽  
Nozzle Guide Vanes

Heat transfer and aerodynamic measurements have been made on the endwalls of an annular cascade of turbine nozzle guide vanes in the presence of film cooling. The results indicate that high levels of cooling effectiveness can be achieved on the endwalls of turbine nozzle guide vanes (NGV). The NGV were operated at the correct engine non-dimensional conditions of Reynolds number, Mach number, gas-to-wall temperature ratio and gas-to-coolant density ratio. The results show that the secondary flow and horse-shoe vortex act on the coolant which is converted towards the suction side of the NGV endwall passage. Consequently the coolant does not quite reach the pressure side/casing trailing edge, leading to diminished cooling in this region. Increasing the blowing rate from 0.52 to 1.1 results in significant reductions in heat transfer to the endwall. Similar trends are evident when the coolant temperature is reduced. Measured heat transfer rates indicate that over most of the endwall region the film cooling reduces the Nusselt number by 50% to 75%.

scholarly journals Unsteady phenomena at the combustor-turbine interface

2021 ◽  
Vol 5 ◽  
pp. 202-215
Author(s):  
Faisal Shaikh ◽  
Budimir Rosic
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
High Speed ◽  
Guide Vane ◽  
Secondary Flows ◽  
Test Facility ◽  
Unsteady Heat Transfer ◽  
Guide Vanes ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes

The combustor-turbine interface in a gas turbine is characterised by complex, highly unsteady flows. In a combined experimental and large eddy simulation (LES) study including realistic combustor geometry, the standard model of secondary flows in the nozzle guide vanes (NGV) is found to be oversimplified. A swirl core is created in the combustion chamber which convects into the first vane passages. Four main consequences of this are identified: variation in vane loading; unsteady heat transfer on vane surfaces; unsteadiness at the leading edge horseshoe vortex, and variation in the position of the passage vortex. These phenomena occur at relatively low frequencies, from 50–300 Hz. It seems likely that these unsteady phenomena result in non-optimal film cooling, and that by reducing unsteadiness designs with greater cooling efficiency could be achieved. Measurements were performed in a high speed test facility modelling a large industrial gas turbine with can combustors, including nozzle guide vanes and combustion chambers. Vane surfaces and endwalls of a nozzle guide vane were instrumented with 384 high speed thin film heat flux gauges, to measure unsteady heat transfer. The high resolution of measurements was such to allow direct visualisation in time of large scale turbulent structures over the endwalls and vane surfaces. A matching LES simulation was carried out in a domain matching experimental conditions including upstream swirl generators and transition duct. Data reduction allowed time-varying LES data to be recorded for several cycles of the unsteady phenomena observed. The combination of LES and experimental data allows physical explanation and visualisation of flow events.

scholarly journals Heat Transfer to Rotating Turbine Blades in a Flow Undisturbed by Wakes

1994 ◽  
Author(s):  
T. Garside ◽  
R. W. Moss ◽  
R. W. Ainsworth ◽  
S. N. Dancer ◽  
M. G. Rose
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Turbine Blades ◽  
Heat Fluxes ◽  
Reverse Direction ◽  
Similar Data ◽  
Blade Surface ◽  
Guide Vanes ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes

The flow over the high pressure blades of a gas turbine is disturbed by wakes and shock waves from the nozzle guide vanes upstream. These disturbances lead to increased heat transfer to the blade surfaces, the accurate prediction of which is an essential stage in the design process. The Oxford Rotor experiment consists of a highly instrumented 0.5 m diameter shroudless turbine which is supplied with air from a piston tube during the 200 ms run time and simulates realistic engine Mach and Reynolds numbers. Previous experiments have measured blade surface pressures and heat transfer rates, and compared them with similar data from linear cascades. The present work is designed to enable the accuracy of rotation terms in computational fluid dynamics (CFD) calculations to be assessed, by providing heat transfer data from the rotating frame in the absence of wakes. Flow disturbances were avoided by removing the nozzle guide vanes, the correct angle of incidence onto the rotor blades being achieved by rotating the rotor in the reverse direction. Blade surface heat fluxes were measured using thin film gauges. In the absence of the usual blade-passing fluctuations, the root-mean-square fluctuation in heat flux was typically only 7% of the DC level. Nusselt numbers are compared with cascade data and CFD predictions from both a three-dimensional viscous Navier-Stokes equation solver and a two-dimensional boundary layer prediction. The low inlet turbulence level produced a long laminar region on the suction surface followed by sudden transition. CFD predictions of Nusselt number on this surface were very sensitive to the choice of boundary layer state, and the experimental level was approximately mid-way between predictions with a transitional intermittency distribution and those with a turbulent distribution. On the pressure surface the levels were approximately 25% below predicted levels, and possible reasons for this are considered.

Heat Transfer Analysis of the Surface of Nonfilm-Cooled and Film-Cooled Nozzle Guide Vanes in Transonic Annular Cascade

2017 ◽  
Author(s):  
Kasem E. Ragab ◽  
Lamyaa El-Gabry
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Guide Vane ◽  
Heat Transfer Analysis ◽  
Guide Vanes ◽  
Cfd Models ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Annular Cascade ◽  
Nozzle Guide Vanes

One of the approaches adopted to improve turbine efficiency and increase power to weight ratio is reducing vane count. In the current study, numerical analysis was performed for the heat transfer over the surface of nozzle guide vanes under the condition of reduced vane count using three dimensional computational fluid dynamics (CFD) models. The investigation has taken place in two stages: the baseline nonfilm-cooled nozzle guide vane, and the film-cooled nozzle guide vane. A finite volume based commercial code (ANSYS CFX 15) was used to build and analyze the CFD models. The investigated annular cascade has no heat transfer measurements available; hence in order to validate the CFD models against experimental data, two standalone studies were carried out on the NASA C3X vanes, one on the nonfilm-cooled C3X vane and the other on the film-cooled C3X vane. Different modelling parameters were investigated including turbulence models in order to obtain good agreement with the C3X experimental data, the same parameters were used afterwards to model the industrial nozzle guide vanes. Three Shear Stress Transport (SST) turbulence model variations were evaluated, the SST with Gamma-Theta transition model was found to yield the best agreement with the experimental results; model capabilities were demonstrated when the laminar to turbulent transition took place.

Sign in / Sign up

Export Citation Format

Share Document