scholarly journals Fluoroscopy-based laser projection system for surgical guidance and its calibration methods

10.29007/m1cq ◽  
2018 ◽  
Author(s):  
Sanghyun Joung ◽  
Hyunwoo Lee ◽  
Chul-Woo Park ◽  
Chnag-Wug Oh ◽  
Il-Hyung Park
Keyword(s):  
Experimental System ◽  
Ccd Camera ◽  
Calibration Method ◽  
Optical Tracking ◽  
Angular Error ◽  
Measurement Unit ◽  
Projection System ◽  
Calibration Phantom ◽  
Calibration Methods ◽  
Laser Module

We have developed a laser projection system, which can project laser on corresponding position to surgical planning drawn at a fluoroscopic image without an optical tracking system. In this paper, we introduce a spatial calibration method between a laser module and a fluoroscope for the laser projection and evaluate its accuracy with a mimic experimental system. The experimental system consists of a laser module, a distance measurement unit and a CCD camera. The laser modules can project arbitrary line on surface by reflecting a point source laser with two galvanometers. We designed a calibration phantom by combining a collimator for accurate laser pattern positioning and stainless steel ball arrays for calculation of an extrinsic parameter of a C-arm fluoroscopy. We set a projection plane having ruler in 400mm distance from the CCD camera, and set 54 points on the screen. The laser module projects points with respect to the set points, and a distance error between set points and projected points and angular error are calculated. The distance errors is 1.5±1.9 mm (average ± standard deviation). Maximum error was 7.5 mm. Angular error was smaller than 2 degrees. The laser projection system and its calibration method shows clinically acceptable accuracy and the clinical application is the next step.

scholarly journals Estimation of 3D Knee Joint Angles during Cycling Using Inertial Sensors: Accuracy of a Novel Sensor-to-Segment Calibration Procedure Based on Pedaling Motion

Sensors ◽  
2019 ◽  
Vol 19 (11) ◽  
pp. 2474 ◽  
Author(s):  
Sébastien Cordillet ◽  
Nicolas Bideau ◽  
Benoit Bideau ◽  
Guillaume Nicolas
Keyword(s):  
Knee Joint ◽  
Inertial Sensor ◽  
External Rotation ◽  
Calibration Method ◽  
Calibration Procedure ◽  
Angle Measurement ◽  
Measurement Unit ◽  
Joint Angles ◽  
Calibration Methods ◽  
Flexion Extension

This paper presents a novel sensor-to-segment calibration procedure for inertial sensor-based knee joint kinematics analysis during cycling. This procedure was designed to be feasible in-field, autonomously, and without any external operator or device. It combines a static standing up posture and a pedaling task. The main goal of this study was to assess the accuracy of the new sensor-to-segment calibration method (denoted as the ‘cycling’ method) by calculating errors in terms of body-segment orientations and 3D knee joint angles using inertial measurement unit (IMU)-based and optoelectronic-based motion capture. To do so, 14 participants were evaluated during pedaling motion at a workload of 100 W, which enabled comparisons of the cycling method with conventional calibration methods commonly employed in gait analysis. The accuracy of the cycling method was comparable to that of other methods concerning the knee flexion/extension angle, and did not exceed 3.8°. However, the cycling method presented the smallest errors for knee internal/external rotation (6.65 ± 1.94°) and abduction/adduction (5.92 ± 2.85°). This study demonstrated that a calibration method based on the completion of a pedaling task combined with a standing posture significantly improved the accuracy of 3D knee joint angle measurement when applied to cycling analysis.

Graph-optimisation-based self-calibration method for IMU/odometer using preintegration theory

2022 ◽  
pp. 1-20
Author(s):  
Shiyu Bai ◽  
Jizhou Lai ◽  
Pin Lyu ◽  
Yiting Cen ◽  
Bingqing Wang ◽  
...  
Keyword(s):  
Inertial Measurement Unit ◽  
Experimental Tests ◽  
Calibration Method ◽  
Measurement Unit ◽  
Integrated Navigation ◽  
Integrated Navigation System ◽  
Self Calibration ◽  
Calibration Methods ◽  
Calibration Accuracy

Determination of calibration parameters is essential for the fusion performance of an inertial measurement unit (IMU) and odometer integrated navigation system. Traditional calibration methods are commonly based on the filter frame, which limits the improvement of the calibration accuracy. This paper proposes a graph-optimisation-based self-calibration method for the IMU/odometer using preintegration theory. Different from existing preintegrations, the complete IMU/odometer preintegration model is derived, which takes into consideration the effects of the scale factor of the odometer, and misalignments in the attitude and position between the IMU and odometer. Then the calibration is implemented by the graph-optimisation method. The KITTI dataset and field experimental tests are carried out to evaluate the effectiveness of the proposed method. The results illustrate that the proposed method outperforms the filter-based calibration method. Meanwhile, the performance of the proposed IMU/odometer preintegration model is optimal compared with the traditional preintegration models.

A Standard Testing and Calibration Procedure for Low Cost MEMS Inertial Sensors and Units

2008 ◽  
Vol 61 (2) ◽  
pp. 323-336 ◽  
Author(s):  
P. Aggarwal ◽  
Z. Syed ◽  
X. Niu ◽  
N. El-Sheimy
Keyword(s):  
Moving Objects ◽  
Inertial Sensors ◽  
Low Cost ◽  
Calibration Method ◽  
Calibration Procedure ◽  
Measurement Unit ◽  
Navigation Systems ◽  
Integrated Navigation ◽  
Mems Sensors ◽  
Calibration Methods

Navigation involves the integration of methodologies and systems for estimating the time varying position and attitude of moving objects. Inertial Navigation Systems (INS) and the Global Positioning System (GPS) are among the most widely used navigation systems. The use of cost effective MEMS based inertial sensors has made GPS/INS integrated navigation systems more affordable. However MEMS sensors suffer from various errors that have to be calibrated and compensated to get acceptable navigation results. Moreover the performance characteristics of these sensors are highly dependent on the environmental conditions such as temperature variations. Hence there is a need for the development of accurate, reliable and efficient thermal models to reduce the effect of these errors that can potentially degrade the system performance. In this paper, the Allan variance method is used to characterize the noise in the MEMS sensors. A six-position calibration method is applied to estimate the deterministic sensor errors such as bias, scale factor, and non-orthogonality. An efficient thermal variation model is proposed and the effectiveness of the proposed calibration methods is investigated through a kinematic van test using integrated GPS and MEMS-based inertial measurement unit (IMU).

scholarly journals A Multi Camera and Multi Laser Calibration Method for 3D Reconstruction of Revolution Parts

Sensors ◽  
2021 ◽  
Vol 21 (3) ◽  
pp. 765
Author(s):  
Hugo Álvarez ◽  
Marcos Alonso ◽  
Jairo R. Sánchez ◽  
Alberto Izaguirre
Keyword(s):  
3D Reconstruction ◽  
Calibration Method ◽  
Laser Plane ◽  
Calibration Methods ◽  
Laser Calibration ◽  
Calibration Object ◽  
Focus Plane ◽  
Chessboard Pattern ◽  
Line Patterns

This paper describes a method for calibrating multi camera and multi laser 3D triangulation systems, particularly for those using Scheimpflug adapters. Under this configuration, the focus plane of the camera is located at the laser plane, making it difficult to use traditional calibration methods, such as chessboard pattern-based strategies. Our method uses a conical calibration object whose intersections with the laser planes generate stepped line patterns that can be used to calculate the camera-laser homographies. The calibration object has been designed to calibrate scanners for revolving surfaces, but it can be easily extended to linear setups. The experiments carried out show that the proposed system has a precision of 0.1 mm.

Stable Calibrations of Six-DOF Serial Robots by Using Identification Models with Equalized Singular Values

Robotica ◽  
2021 ◽  
pp. 1-22
Author(s):  
Zhouxiang Jiang ◽  
Min Huang
Keyword(s):  
Industrial Robot ◽  
Singular Values ◽  
Calibration Method ◽  
Identification Accuracy ◽  
Condition Numbers ◽  
Measurement Instruments ◽  
Unknown Parameters ◽  
Calibration Methods ◽  
Six Dof ◽  
The Stability

SUMMARY In typical calibration methods (kinematic or non-kinematic) for serial industrial robot, though measurement instruments with high resolutions are adopted, measurement configurations are optimized, and redundant parameters are eliminated from identification model, calibration accuracy is still limited under measurement noise. This might be because huge gaps still exist among the singular values of typical identification Jacobians, thereby causing the identification models ill conditioned. This paper addresses such problem by using new identification models established in two steps. First, the typical models are divided into the submodels with truncated singular values. In this way, the unknown parameters corresponding to the abnormal singular values are removed, thereby reducing the condition numbers of the new submodels. However, these models might still be ill conditioned. Therefore, the second step is to further centralize the singular values of each submodel by using a matrix balance method. Afterward, all submodels are well conditioned and obtain much higher observability indices compared with those of typical models. Simulation results indicate that significant improvements in the stability of identification results and the identifiability of unknown parameters are acquired by using the new identification submodels. Experimental results indicate that the proposed calibration method increases the identification accuracy without incurring additional hardware setup costs to the typical calibration method.

scholarly journals Vicarious Radiometric Calibration of Ocean Color Bands for FY-3D/MERSI-II at Lake Qinghai, China

Sensors ◽  
2020 ◽  
Vol 21 (1) ◽  
pp. 139
Author(s):  
Shengli Chen ◽  
Xiaobing Zheng ◽  
Xin Li ◽  
Wei Wei ◽  
Shenda Du ◽  
...  
Keyword(s):  
Infrared Imaging ◽  
Large Deviation ◽  
Ocean Color ◽  
Calibration Method ◽  
Surface Measurement ◽  
Radiometric Calibration ◽  
Lake Qinghai ◽  
Vicarious Calibration ◽  
Calibration Methods ◽  
Spectral Imager

To calibrate the low signal response of the ocean color (OC) bands and test the stability of the Fengyun-3D (FY-3D)/Medium Resolution Spectral Imager II (MERSI-II), an absolute radiometric calibration field test of FY-3D/MERSI-II at the Lake Qinghai Radiometric Calibration Site (RCS) was carried out in August 2018. The lake surface and atmospheric parameters were mainly measured by advanced observation instruments, and the MODerate spectral resolution atmospheric TRANsmittance algorithm and computer model (MODTRAN4.0) was used to simulate the multiple scattering radiance value at the altitude of the sensor. The results showed that the relative deviations between bands 9 and 12 are within 5.0%, while the relative deviations of bands 8, and 13 are 17.1%, and 12.0%, respectively. The precision of the calibration method was verified by calibrating the Aqua/Moderate-resolution Imaging Spectroradiometer (MODIS) and National Polar-orbiting Partnership (NPP)/Visible Infrared Imaging Radiometer (VIIRS), and the deviation of the calibration results was evaluated with the results of the Dunhuang RCS calibration and lunar calibration. The results showed that the relative deviations of NPP/VIIRS were within 7.0%, and the relative deviations of Aqua/MODIS were within 4.1% from 400 nm to 600 nm. The comparisons of three on-orbit calibration methods indicated that band 8 exhibited a large attenuation after launch and the calibration results had good consistency at the other bands except for band 13. The uncertainty value of the whole calibration system was approximately 6.3%, and the uncertainty brought by the field surface measurement reached 5.4%, which might be the main reason for the relatively large deviation of band 13. This study verifies the feasibility of the vicarious calibration method at the Lake Qinghai RCS and provides the basis and reference for the subsequent on-orbit calibration of FY-3D/MERSI-II.

scholarly journals Optimization-Based Online Initialization and Calibration of Monocular Visual-Inertial Odometry Considering Spatial-Temporal Constraints

Sensors ◽  
2021 ◽  
Vol 21 (8) ◽  
pp. 2673
Author(s):  
Weibo Huang ◽  
Weiwei Wan ◽  
Hong Liu
Keyword(s):  
Measurement Data ◽  
Calibration Method ◽  
Bundle Adjustment ◽  
Measurement Unit ◽  
Temporal Parameters ◽  
Work Routine ◽  
Initial States ◽  
Time Offset ◽  
Public Datasets ◽  
Metric Scale

The online system state initialization and simultaneous spatial-temporal calibration are critical for monocular Visual-Inertial Odometry (VIO) since these parameters are either not well provided or even unknown. Although impressive performance has been achieved, most of the existing methods are designed for filter-based VIOs. For the optimization-based VIOs, there is not much online spatial-temporal calibration method in the literature. In this paper, we propose an optimization-based online initialization and spatial-temporal calibration method for VIO. The method does not need any prior knowledge about spatial and temporal configurations. It estimates the initial states of metric-scale, velocity, gravity, Inertial Measurement Unit (IMU) biases, and calibrates the coordinate transformation and time offsets between the camera and IMU sensors. The work routine of the method is as follows. First, it uses a time offset model and two short-term motion interpolation algorithms to align and interpolate the camera and IMU measurement data. Then, the aligned and interpolated results are sent to an incremental estimator to estimate the initial states and the spatial–temporal parameters. After that, a bundle adjustment is additionally included to improve the accuracy of the estimated results. Experiments using both synthetic and public datasets are performed to examine the performance of the proposed method. The results show that both the initial states and the spatial-temporal parameters can be well estimated. The method outperforms other contemporary methods used for comparison.

scholarly journals Cobot User Frame Calibration: Evaluation and Comparison between Positioning Repeatability Performances Achieved by Traditional and Vision-Based Methods

Robotics ◽  
2021 ◽  
Vol 10 (1) ◽  
pp. 45
Author(s):  
Roberto Pagani ◽  
Cristina Nuzzi ◽  
Marco Ghidelli ◽  
Alberto Borboni ◽  
Matteo Lancini ◽  
...  
Keyword(s):  
Quantitative Analysis ◽  
Production Line ◽  
Calibration Method ◽  
Fiducial Marker ◽  
Positioning System ◽  
Local Calibration ◽  
Calibration Methods ◽  
Robot Positioning ◽  
Good Repeatability ◽  
Calibration Time

Since cobots are designed to be flexible, they are frequently repositioned to change the production line according to the needs; hence, their working area (user frame) needs to be often calibrated. Therefore, it is important to adopt a fast and intuitive user frame calibration method that allows even non-expert users to perform the procedure effectively, reducing the possible mistakes that may arise in such contexts. The aim of this work was to quantitatively assess the performance of different user frame calibration procedures in terms of accuracy, complexity, and calibration time, to allow a reliable choice of which calibration method to adopt and the number of calibration points to use, given the requirements of the specific application. This has been done by first analyzing the performances of a Rethink Robotics Sawyer robot built-in user frame calibration method (Robot Positioning System, RPS) based on the analysis of a fiducial marker distortion obtained from the image acquired by the wrist camera. This resulted in a quantitative analysis of the limitations of this approach that only computes local calibration planes, highlighting the reduction of performances observed. Hence, the analysis focused on the comparison between two traditional calibration methods involving rigid markers to determine the best number of calibration points to adopt to achieve good repeatability performances. The analysis shows that, among the three methods, the RPS one resulted in very poor repeatability performances (1.42 mm), while the three and five points calibration methods achieve lower values (0.33 mm and 0.12 mm, respectively) which are closer to the reference repeatability (0.08 mm). Moreover, comparing the overall calibration times achieved by the three methods, it is shown that, incrementing the number of calibration points to more than five, it is not suggested since it could lead to a plateau in the performances, while increasing the overall calibration time.

Systematic Calibration Method for FOG Inertial Measurement Units

2013 ◽  
Vol 662 ◽  
pp. 717-720 ◽  
Author(s):  
Zhen Yu Zheng ◽  
Yan Bin Gao ◽  
Kun Peng He
Keyword(s):  
Inertial Measurement Unit ◽  
Inertial Sensors ◽  
Calibration Method ◽  
State Equation ◽  
Measurement Unit ◽  
Observation System ◽  
Body Frame ◽  
Inertial Measurement ◽  
Measurement Units ◽  
Error Coefficients

As an inertial sensors assembly, the FOG inertial measurement unit (FIMU) must be calibrated before being used. The paper presents a one-time systematic IMU calibration method only using two-axis low precision turntable. First, the detail error model of inertial sensors using defined body frame is established. Then, only velocity taken as observation, system 33 state equation is established including the lever arm effects and nonlinear terms of scale factor error. The turntable experiments verify that the method can identify all the error coefficients of FIMU on low-precision two-axis turntable, after calibration the accuracy of navigation is improved.

CCD Camera Calibration Technology Based on the Translation of Coordinate Measuring Machine

2014 ◽  
Vol 568-570 ◽  
pp. 320-325 ◽  
Author(s):  
Feng Shan Huang ◽  
Li Chen
Keyword(s):  
Coordinate System ◽  
Camera Calibration ◽  
Characteristic Point ◽  
Coordinate Measuring Machine ◽  
Ccd Camera ◽  
Mathematic Model ◽  
Calibration Method ◽  
Calibration Characteristic ◽  
Standard Sphere ◽  
Measuring Machine

A new CCD camera calibration method based on the translation of Coordinate Measuring Machine (CMM) is proposed. The CMM brings the CCD camera to produce the relative translation with respect to the center of the white ceramic standard sphere along the X, Y, Z axis, and the coordinates of the different positions of the calibration characteristic point in the probe coordinate system can be generated. Meanwhile, the camera captures the image of the white ceramic standard sphere at every position, and the coordinates of the calibration characteristic point in the computer frame coordinate system can be registered. The calibration mathematic model was established, and the calibration steps were given and the calibration system was set up. The comparing calibration result shows that precision of this method is equivalent to that of the special calibration method, and the difference between the calibrating data of these two methods is within ±1μm.

Sign in / Sign up

Export Citation Format

Share Document