scholarly journals ANALYSIS OF THE EFFECT OF BYPASS RATIO ON PERFORMANCE ENGINE CFM56-5A1 IN CRUISING CONDITIONS

Vortex ◽  
2020 ◽  
Vol 1 (1) ◽  
pp. 39
Author(s):  
Opri Surya Yustinoto
Keyword(s):  
Fuel Consumption ◽  
Engine Performance ◽  
Specific Fuel Consumption ◽  
Bypass Ratio ◽  
Consumption Value

The value of engine performance is known to decrease and increase with increasing and decreasing variation of the value of the parameter bypass ratio, so that if the value of these parameters is greater, then the fuel consumption when the aircraft operates will be less and the thrust will decrease. In addition to changing the value of the specific fuel consumption due to the influence of the bypass value, variations in altitude are also very influential where the higher the aircraft, the resulting specific fuel consumption value will be smaller 

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Characteristics of Water-in-Diesel Emulsions in a Single Cylinder Compression Ignition Engine

2014 ◽  
Author(s):  
Teja Gonguntla ◽  
Robert Raine ◽  
Leigh Ramsey ◽  
Thomas Houlihan
Keyword(s):  
Fuel Consumption ◽  
Direct Injection ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Compression Ignition Engine ◽  
Oil Emulsion ◽  
Single Cylinder ◽  
Performance And Emission

The objective of this project was to develop both engine performance and emission profiles for two test fuels — a 6% water-in-diesel oil emulsion (DOE-6) fuel and a neat diesel (D100) fuel. The testing was performed on a single cylinder, direct-injection, water-cooled diesel engine coupled to an eddy current dynamometer. Output parameters of the engine were used to calculate Brake Specific Fuel Consumption (BSFC) and Engine Efficiency (η) for each test fuel. DOE-6 fuels generated a 24% reduction in NOX and a 42% reduction in Carbon Monoxide emissions over the tested operating conditions. DOE-6 fuels presented higher ignition delays — between 1°-4°, yielded 1%–12% lower peak cylinder pressures and produced up to 5.5% lower exhaust temperatures. Brake Specific Fuel consumption increased by 6.6% for the DOE-6 fuels as compared to the D100 fuels. This project is the first research done by a New Zealand academic institution on water-in-diesel emulsion fuels.

Optimization of Turbofan Propulsion Cycle Using a Genetic Algorithm

2010 ◽  
Author(s):  
Adel Ghenaiet
Keyword(s):  
Genetic Algorithm ◽  
Fuel Consumption ◽  
Pressure Ratio ◽  
Engine Performance ◽  
Optimization Procedure ◽  
Specific Fuel Consumption ◽  
High Mass ◽  
Design Parameters ◽  
Inlet Temperature ◽  
Simplifying Assumptions

This paper presents an evolutionary approach as the optimization framework to design for the optimal performance of a high-bypass unmixed turbofan to match with the power requirements of a commercial aircraft. The parametric analysis had the objective to highlight the effects of the principal design parameters on the propulsive performance in terms of specific fuel consumption and specific thrust. The design optimization procedure based on the genetic algorithm PIKAIA coupled to the developed engine performance analyzer (on-design and off-design) aimed at finding the propulsion cycle parameters minimizing the specific fuel consumption, while meeting the required thrusts in cruise and takeoff and the restrictions of temperatures limits, engine size and weight as well as pollutants emissions. This methodology does not use engine components’ maps and operates on simplifying assumptions which are satisfying the conceptual or early design stages. The predefined requirements and design constraints have resulted in an engine with high mass flow rate, bypass ratio and overall pressure ratio and a moderate turbine inlet temperature. In general, the optimized engine is fairly comparable with available engines of equivalent power range.

scholarly journals Control of Exhaust Emissions Using Piston Coating on Two-StrokeSI Engines with Gasoline Blends

2021 ◽  
Vol 8 (1) ◽  
pp. H16-H20
Author(s):  
A.V.N.S. Kiran ◽  
B. Ramanjaneyulu ◽  
M. Lokanath M. ◽  
S. Nagendra ◽  
G.E. Balachander
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Specific Fuel Consumption ◽  
Thermal Barrier ◽  
Piston Crown ◽  
Barrier Coating

An increase in fuel utilization to internal combustion engines, variation in gasoline price, reduction of the fossil fuels and natural resources, needs less carbon content in fuel to find an alternative fuel. This paper presents a comparative study of various gasoline blends in a single-cylinder two-stroke SI engine. The present experimental investigation with gasoline blends of butanol and propanol and magnesium partially stabilized zirconium (Mg-PSZ) as thermal barrier coating on piston crown of 100 µm. The samples of gasoline blends were blended with petrol in 1:4 ratios: 20 % of butanol and 80 % of gasoline; 20 % of propanol and 80 % of gasoline. In this work, the following engine characteristics of brake thermal efficiency (BTH), specific fuel consumption (SFC), HC, and CO emissions were measured for both coated and non-coated pistons. Experiments have shown that the thermal efficiency is increased by 2.2 % at P20. The specific fuel consumption is minimized by 2.2 % at P20. Exhaust emissions are minimized by 2.0 % of HC and 2.4 % of CO at B20. The results strongly indicate that the combination of thermal barrier coatings and gasoline blends can improve engine performance and reduce exhaust emissions.

scholarly journals Rancang Bangun dan Pengujian Penghalang Heliks sebagai Pencampur Udara-Biogas pada Motor Otto

2021 ◽  
Vol 8 (3) ◽  
pp. 89-96
Author(s):  
Herbert Hasudungan Siahaan ◽  
Armansyah H Tambunan ◽  
Desrial ◽  
Soni Solistia Wirawan
Keyword(s):  
Fuel Consumption ◽  
Performance Test ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Specific Fuel Consumption ◽  
Combustion Reaction ◽  
Otto Cycle ◽  
Direct Use ◽  
Engine Power

A helical barrier as air-biogas mixing device was designed and tested for direct use of biogas from digester in otto cycle generator set. Homogeneity of the air-fuel mixture can give better combustion reaction and increase engine power. The design was based on simulation, which shows that a 0.039 m length of helical barrier gave a 5% increase in power compared to non-helical barrier. Likewise, the simulations also showed that the helical barrier reduced specific fuel consumption (SFC) by 8%. Accordingly, the mixer with helical barrier was designed, and fabricated. Its performance test confirms the improvement resulted by using helical barriers as air-biogas mixer in the engine. The experiment showed that the power increased by 5% when using helical barrier, while SFC decreased by 4.5%. It is concluded that the helical barrier can increase the homogeneity of the mixture resulting in better engine performance. Besides, emissions produced from the engine using a helical barrier also decreased.

Optimizing Separate Exhaust Turbofans for Cruise Specific Fuel Consumption

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Syed J. Khalid
Keyword(s):  
Fuel Consumption ◽  
Control Algorithm ◽  
Velocity Ratio ◽  
Transmission Efficiency ◽  
Specific Fuel Consumption ◽  
Variable Geometry ◽  
Nozzle Throat ◽  
Propulsive Efficiency ◽  
Turbofan Engines ◽  
Bypass Ratio

Cruise specific fuel consumption (SFC) of turbofan engines is a key metric for increasing airline profitability and for reducing CO2 emissions. Although increasing design bypass ratio (BPR) of separate exhaust turbofan configurations improves cruise SFC, further improvements can be obtained with online control actuated variable geometry modulations of bypass nozzle throat area, core nozzle throat area, and compressor variable vanes (CVV/CVG). The scope of this paper is to show only the benefits possible, and the process used in determining those benefits, and not to suggest any particular control algorithm for searching the best combination of the control effectors. A parametric cycle study indicated that the effector modulations could increase the cruise BPR, core efficiency, transmission efficiency, propulsive efficiency, and ideal velocity ratio resulting in a cruise SFC improvement of as much as 2.6% depending upon the engine configuration. The changes in these metrics with control effector variations will be presented. Scheduling of CVV is already possible in legacy digital controls; perturbation to this schedule and modulation of nozzle areas should be explored in light of the low bandwidth requirements at steady-state cruise conditions.

Thermodynamics Cycle Analysis, Pressure Loss and Heat Transfer Assessment of a Recuperative System for Aero Engines

2014 ◽  
Author(s):  
A. Goulas ◽  
S. Donnerhack ◽  
M. Flouros ◽  
D. Misirlis ◽  
Z. Vlahostergios ◽  
...  
Keyword(s):  
Combustion Chamber ◽  
Fuel Consumption ◽  
Heat Exchangers ◽  
Engine Performance ◽  
Specific Fuel Consumption ◽  
Hot Gas ◽  
Research Activities ◽  
Aero Engine ◽  
Overall Efficiency ◽  
Aero Engines

Aiming in the direction of designing more efficient aero engines, various concepts have been developed in recent years, among which is the concept of an intercooled and recuperative aero engine. Particularly in the area of recuperation, MTU Aero Engines has been driving research activities in the last decade. This concept is based on the use of a system of heat exchangers mounted inside the hot-gas exhaust nozzle (recuperator). Through the operation of the system of heat exchangers, the heat from the exhaust gas, downstream the LP turbine of the jet engine is driven back to the combustion chamber. Thus, the preheated air enters the engine combustion chamber with increased enthalpy, providing improved combustion and by consequence, increased fuel economy and low-level emissions. If additionally an intercooler is placed between the compressor stages of the aero engine, the compressed air is then cooled by the intercooler thus, less compression work is required to reach the compressor target pressure. In this paper an overall assessment of the system is presented with particular focus on the recuperative system and the heat exchangers mounted into the aero engine’s exhaust nozzle. The herein presented results were based on the combined use of CFD computations, experimental measurements and thermodynamic cycle analysis. They focus on the effects of total pressure losses and heat exchanger efficiency on the aero engine performance especially the engine’s overall efficiency and the specific fuel consumption. More specifically, two different hot-gas exhaust nozzle configurations incorporating modifications in the system of heat exchangers are examined. The results show that significant improvements can be achieved in overall efficiency and specific fuel consumption hence contributing into the reduction of CO2 and NOx emissions. The design of a more sophisticated recuperation system can lead to further improvements in the aero engine efficiency in the reduction of fuel consumption. This work is part of the European funded research program LEMCOTEC (Low Emissions Core engine Technologies).

Analyses and Optimization of a Propulsion Cycle for Unmixed High Bypass Turbofan

2008 ◽  
Author(s):  
Adel Ghenaiet
Keyword(s):  
Fuel Consumption ◽  
Pressure Ratio ◽  
Specific Fuel Consumption ◽  
Design Parameters ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
High Pressure Ratio ◽  
Turbine Inlet ◽  
Design Variables ◽  
Bypass Ratio

This paper deals with a parametric study and an optimization for the design variables of a high bypass unmixed turbofan equipping commercial aircrafts. The objective of the first part of this study is to highlight the effects of the principal design parameters (bypass ratio, compression ratios, turbine inlet temperature etc..) on the uninstalled performance, in terms of specific thrust and specific fuel consumption. The second part concerns the optimization, aiming at finding the optimum design parameters concurrently minimizing the specific fuel consumption at cruise, and meeting the thrust requirement at takeoff. The cycle analyzer (on-design and off-design) as coupled to the optimization algorithm MMFD by adopting a random multi-starts search strategy is shown to be stable and converging. The predefined requirements and constraints have dictated utilizing an engine with a high-bypass ratio, high-pressure ratio and a moderate turbine inlet temperature. In general, the obtained results compare fairly well with typical data available for an equivalent ‘reference’ engine. This elaborated methodology is shown to be consistent with the conceptual design requirements and accuracy, because, it does not use components’ characteristics, and operates on simplifying assumptions. This present methodology can be readily adapted for other configurations of aero-engines as well, and easily integrated in a multi-disciplinary design approach.

Effects of Micro-Emulsion Fuels on the Performance and Emissions of Diesel Engine

2011 ◽  
Vol 236-238 ◽  
pp. 151-154 ◽  
Author(s):  
Jia Quan Wang ◽  
Ping Sun ◽  
Zhen Chen ◽  
De Qing Mei
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Specific Fuel Consumption ◽  
Performance And Emissions ◽  
Micro Emulsion ◽  
Effects Of Temperature ◽  
The Stability

The micro-emulsion fuels were prepared with complex surfactant, and the effects of temperature on the stability of these fuels were investigated. The engine performance and the emissions were studied when the engine was fueled with diesel and micro-emulsion diesel respectively. Results showed that when the engine was fueled with micro-emulsion diesel, the NOXand smoke emissions were decreased obviously and HC and CO emissions were increased slightly. Discounting of surfactant and water, the specific fuel consumption of micro-emulsion diesel was lower than those of diesel under any load at the speed of 2900r/min.

Fundamental Differences Between Conventional and Geared Turbofans

2009 ◽  
Author(s):  
Joachim Kurzke
Keyword(s):  
Fuel Consumption ◽  
Real Option ◽  
Pressure Ratio ◽  
Thermodynamic Cycle ◽  
Specific Fuel Consumption ◽  
Thermodynamic Efficiency ◽  
Aircraft Engines ◽  
Direct Drive ◽  
Significant Difference ◽  
Bypass Ratio

The potential for improving the thermodynamic efficiency of aircraft engines is limited because the aerodynamic quality of the turbomachines has already achieved a very high level. While in the past increasing burner exit temperature did contribute to better cycle efficiency, this is no longer the case with today’s temperatures in the range of 1900...2000K. Increasing the cycle pressure ratio above 40 will yield only a small fuel consumption benefit. Therefore the only way to improve the fuel efficiency of aircraft engines significantly is to increase bypass ratio — which yields higher propulsive efficiency. A purely thermodynamic cycle study shows that specific fuel consumption decreases continuously with increasing bypass ratio. However, thermodynamics alone is a too simplistic view of the problem. A conventional direct drive turbofan of bypass ratio 6 looks very different to an engine with bypass ratio 10. Increasing bypass ratio above 10 makes it attractive to design an engine with a gearbox to separate the fan speed from the other low pressure components. Different rules apply for optimizing turbofans of conventional designs and those with a gearbox. This paper describes various criteria to be considered for optimizing the respective engines and their components. For illustrating the main differences between conventional and geared turbofans it is assumed that an existing core of medium pressure ratio with a two stage high pressure turbine is to be used. The design of the engines is done for takeoff rating because this is the mechanically most challenging condition. For each engine the flow annulus is examined and stress calculations for the disks are performed. The result of the integrated aero-thermodynamic and mechanical study allows a comparison of the fundamental differences between conventional and geared turbofans. At the same bypass ratio there will be no significant difference in specific fuel consumption between the alternative designs. The main difference is in the parts count which is much lower for the geared turbofan than for the conventional engine. However, these parts will be mechanically much more challenging than those of a conventional turbofan. If the bypass ratio is increased significantly above 10, then the geared turbofan becomes more and more attractive and the conventional turbofan design is no longer a real option. The maximum practical bypass ratio for ducted fans depends on the nacelle drag and how the installation problems can be solved.

Sign in / Sign up

Export Citation Format

Share Document