scholarly journals The Ecological Footprint and Driving Force Measurement Analysis of the Xinjiang Akesu Area Based on Gray model

2017 ◽  
Keyword(s):  
Driving Force ◽  
Ecological Footprint ◽  
Force Measurement ◽  
Gray Model ◽  
Measurement Analysis

In situ TEM Studies of agglomeration of sub-nanometer Ru layers in Ru/C multilayers

1992 ◽  
Vol 50 (1) ◽  
pp. 256-257
Author(s):  
Tai D. Nguyen ◽  
Ronald Gronsky ◽  
Jeffrey B. Kortright
Keyword(s):  
Layered Structure ◽  
Driving Force ◽  
High Energy ◽  
Superior Performance ◽  
In Situ Tem ◽  
Rayleigh Instability ◽  
Practical Applications ◽  
Transmission Electron ◽  
Diffraction Patterns

Nanometer period Ru/C multilayers are one of the prime candidates for normal incident reflecting mirrors at wavelengths < 10 nm. Superior performance, which requires uniform layers and smooth interfaces, and high stability of the layered structure under thermal loadings are some of the demands in practical applications. Previous studies however show that the Ru layers in the 2 nm period Ru/C multilayer agglomerate upon moderate annealing, and the layered structure is no longer retained. This agglomeration and crystallization of the Ru layers upon annealing to form almost spherical crystallites is a result of the reduction of surface or interfacial energy from die amorphous high energy non-equilibrium state of the as-prepared sample dirough diffusive arrangements of the atoms. Proposed models for mechanism of thin film agglomeration include one analogous to Rayleigh instability, and grain boundary grooving in polycrystalline films. These models however are not necessarily appropriate to explain for the agglomeration in the sub-nanometer amorphous Ru layers in Ru/C multilayers. The Ru-C phase diagram shows a wide miscible gap, which indicates the preference of phase separation between these two materials and provides an additional driving force for agglomeration. In this paper, we study the evolution of the microstructures and layered structure via in-situ Transmission Electron Microscopy (TEM), and attempt to determine the order of occurence of agglomeration and crystallization in the Ru layers by observing the diffraction patterns.

The nucleation of cavities at grain boundaries

1987 ◽  
Vol 45 ◽  
pp. 288-291
Author(s):  
P. J. Goodhew
Keyword(s):  
Surface Tension ◽  
Surface Energy ◽  
Grain Boundaries ◽  
Radiation Damage ◽  
Impurity Concentration ◽  
Driving Force ◽  
Nucleation And Growth ◽  
Phase Boundaries ◽  
Cavity Nucleation ◽  
Spherical Bubble

Cavity nucleation and growth at grain and phase boundaries is of concern because it can lead to failure during creep and can lead to embrittlement as a result of radiation damage. Two major types of cavity are usually distinguished: The term bubble is applied to a cavity which contains gas at a pressure which is at least sufficient to support the surface tension (2g/r for a spherical bubble of radius r and surface energy g). The term void is generally applied to any cavity which contains less gas than this, but is not necessarily empty of gas. A void would therefore tend to shrink in the absence of any imposed driving force for growth, whereas a bubble would be stable or would tend to grow. It is widely considered that cavity nucleation always requires the presence of one or more gas atoms. However since it is extremely difficult to prepare experimental materials with a gas impurity concentration lower than their eventual cavity concentration there is little to be gained by debating this point.

Positive Associations Primacy in the IAT

2011 ◽  
Vol 58 (5) ◽  
pp. 376-384 ◽  
Author(s):  
Pasquale Anselmi ◽  
Michelangelo Vianello ◽  
Egidio Robusto
Keyword(s):  
Implicit Association Test ◽  
Rasch Measurement ◽  
Normal Weight ◽  
Association Test ◽  
Primacy Effect ◽  
Implicit Association ◽  
Obese People ◽  
Measurement Analysis ◽  
Implicit Prejudice

Two studies investigated the different contribution of positive and negative associations to the size of the Implicit Association Test (IAT) effect. A Many-Facet Rasch Measurement analysis was applied for the purpose. Across different IATs (Race and Weight) and different groups of respondents (White, Normal weight, and Obese people) we observed that positive words increase the IAT effect whereas negative words tend to decrease it. Results suggest that the IAT is influenced by a positive associations primacy effect. As a consequence, we argue that researchers should be careful when interpreting IAT effects as a measure of implicit prejudice.

The driving force of craniopharyngioma growth

2014 ◽  
Vol 122 (03) ◽  
Author(s):  
C Stache ◽  
A Hölsken ◽  
SM Schlaffer ◽  
A Hess ◽  
M Metzler ◽  
...  
Keyword(s):  
Driving Force

Failure to control inflammation as a driving force of symptoms and phenotype in the NSG mouse model of ulcerative colitis

2018 ◽  
Author(s):  
H Jodeleit ◽  
P Palamides ◽  
O Al-amodi ◽  
G Beikircher ◽  
S Schönthaler ◽  
...  
Keyword(s):  
Ulcerative Colitis ◽  
Mouse Model ◽  
Driving Force ◽  
Nsg Mouse

Analysis of magnetic force and dynamic characteristic for non-contact permanent magnet linear drive device

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1337-1345
Author(s):  
Chuan Zhao ◽  
Feng Sun ◽  
Junjie Jin ◽  
Mingwei Bo ◽  
Fangchao Xu ◽  
...  
Keyword(s):  
Finite Element ◽  
Permanent Magnet ◽  
Dynamic Characteristic ◽  
Driving Force ◽  
Magnetic Circuit ◽  
Response Speed ◽  
Computation Method ◽  
Element Analysis ◽  
Element Simulation ◽  
The Relationship

This paper proposes a computation method using the equivalent magnetic circuit to analyze the driving force for the non-contact permanent magnet linear drive system. In this device, the magnetic driving force is related to the rotation angle of driving wheels. The relationship is verified by finite element analysis and measuring experiments. The result of finite element simulation is in good agreement with the model established by the equivalent magnetic circuit. Then experiments of displacement control are carried out to test the dynamic characteristic of this system. The controller of the system adopts the combination control of displacement and angle. The results indicate that the system has good performance in steady-state error and response speed, while the maximum overshoot needs to be reduced.

Sign in / Sign up

Export Citation Format

Share Document