In-House Drilling Simulator and Bicenter Drill-Bit Technology Set a New Hardware Benchmark for Separation Between the Bit and Gamma Ray Adapter

2019 ◽  
Author(s):  
Sajjad Hussain ◽  
Alberto Caycedo ◽  
Simon Downie ◽  
Karam Sulaiman Dhaher
Keyword(s):  
Gamma Ray ◽  
Drill Bit

In-House Drilling Simulator and Bicenter Drill-Bit Technology Set a New Hardware Benchmark for Separation Between the Bit and Gamma Ray Adapter

2019 ◽  
Author(s):  
Sajjad Hussain ◽  
Alberto Caycedo ◽  
Simon Downie ◽  
Karam Sulaiman Dhaher
Keyword(s):  
Gamma Ray ◽  
Drill Bit

On the possible gamma-ray source in Cygnus

1967 ◽  
Vol 31 ◽  
pp. 469-471
Author(s):  
J. G. Duthie ◽  
M. P. Savedoff ◽  
R. Cobb
Keyword(s):  
Gamma Rays ◽  
Gamma Ray ◽  
Right Ascension

A source of gamma rays has been found at right ascension 20h15m, declination +35°, with an uncertainty of 6° in each coordinate. Its flux is (1·5 ± 0·8) x 10-4photons cm-2sec-1at 100 MeV. Possible identifications are reviewed, but no conclusion is reached. The mechanism producing the radiation is also uncertain.

Solar Flare Energetic Neutral Emission Measurements in the Project Coronas-I

1994 ◽  
Vol 144 ◽  
pp. 635-639
Author(s):  
J. Baláž ◽  
A. V. Dmitriev ◽  
M. A. Kovalevskaya ◽  
K. Kudela ◽  
S. N. Kuznetsov ◽  
...  
Keyword(s):  
Solar Flare ◽  
Energy Range ◽  
Gamma Rays ◽  
Pulse Shape ◽  
Gamma Ray ◽  
Pulse Shape Discrimination ◽  
Shape Discrimination ◽  
Solar Neutron ◽  
Low Altitude

AbstractThe experiment SONG (SOlar Neutron and Gamma rays) for the low altitude satellite CORONAS-I is described. The instrument is capable to provide gamma-ray line and continuum detection in the energy range 0.1 – 100 MeV as well as detection of neutrons with energies above 30 MeV. As a by-product, the electrons in the range 11 – 108 MeV will be measured too. The pulse shape discrimination technique (PSD) is used.

Preparation of cross-sectional samples for near-surface TEM studies

1987 ◽  
Vol 45 ◽  
pp. 380-381
Author(s):  
R.C. Dickenson ◽  
K.R. Lawless
Keyword(s):  
Standard Sample ◽  
Surface Region ◽  
Specimen Preparation ◽  
Thick Sheet ◽  
Drill Bit ◽  
Sample Holder ◽  
Metal Interface ◽  
Cross Sectional ◽  
Near Surface ◽  
Cold Worked

In thermal oxidation studies, the structure of the oxide-metal interface and the near-surface region is of great importance. A technique has been developed for constructing cross-sectional samples of oxidized aluminum alloys, which reveal these regions. The specimen preparation procedure is as follows: An ultra-sonic drill is used to cut a 3mm diameter disc from a 1.0mm thick sheet of the material. The disc is mounted on a brass block with low-melting wax, and a 1.0mm hole is drilled in the disc using a #60 drill bit. The drill is positioned so that the edge of the hole is tangent to the center of the disc (Fig. 1) . The disc is removed from the mount and cleaned with acetone to remove any traces of wax. To remove the cold-worked layer from the surface of the hole, the disc is placed in a standard sample holder for a Tenupol electropolisher so that the hole is in the center of the area to be polished.

Sign in / Sign up

Export Citation Format

Share Document