scholarly journals Exploration of a Reacting Jet-in-Crossflow in a High-Pressure Axial Stage Combustor

Author(s):  
Tommy Genova ◽  
Michelle Otero ◽  
Bernhard Stiehl ◽  
Jonathan Reyes ◽  
Scott M. Martin ◽  
...  
2021 ◽  
Author(s):  
Bernhard Stiehl ◽  
Michelle Otero ◽  
Tommy Genova ◽  
Tyler Worbington ◽  
Jonathan Reyes ◽  
...  

Author(s):  
Tommy Genova ◽  
Bernhard Stiehl ◽  
Michelle Otero ◽  
Kareem A. Ahmed ◽  
Scott M. Martin

2021 ◽  
Author(s):  
Tommy Genova ◽  
Michelle Otero ◽  
Max K. Fortin ◽  
Michael Tonarely ◽  
Bernhard Stiehl ◽  
...  

Author(s):  
Bernhard Stiehl ◽  
Michelle Otero ◽  
Tommy Genova ◽  
Tyler Worbington ◽  
Jonathan Reyes ◽  
...  

Abstract In this paper we explore the operational map of a lean axial-staged combustor of premixed and partially premixed reacting jet-in-crossflow flames at high-pressure (5 atm). This study attempts to expand the data to relatively high pressure and could significantly aid scaling to real gas turbine engine conditions at 20-30 atm. High speed camera, PIV, CH* chemiluminescence, temperature and pressure measurements were taken and processed to allow accurate reconstruction of six operating points relative to CFD simulations under minimal adjustments. Variation of lean main stage (f = 0.575 and 0.73) and rich jet (f = 1.1, 4 and 8) equivalence ratio has been investigated for a four mm axial jet. The fully premixed flames were found to be controlled by the crossflow temperature before ignition and the crossflow oxygen content during combustion. Analysis of flame shape and position for the partially premixed operating points describes a lee stabilized as well as a more unsteady windward flame branch. Adjustment of added jet fuel and crossflow temperature along with its corresponding oxygen level is required to attain a compact flame body. The risk of delaying combustion progress is significantly increased at a richer jet f = 8 and an overshooting, spatially divided flame was attained with a main stage f = 0.73. Control towards a compact flame body is critical to allow combustion at reasonable reaction rate.


2021 ◽  
Author(s):  
Michelle Otero ◽  
Tommy Genova ◽  
Michael Tonarely ◽  
Max K. Fortin ◽  
Bernhard Stiehl ◽  
...  

2021 ◽  
Author(s):  
Max K. Fortin ◽  
Michelle Otero ◽  
Tommy Genova ◽  
Michael Tonarely ◽  
Kareem A. Ahmed

Author(s):  
Bernhard Stiehl ◽  
Michelle Otero ◽  
Tommy Genova ◽  
Tyler Worbington ◽  
Jonathan Reyes ◽  
...  

Abstract In this paper we explore the operational map of a lean axial-staged combustor of premixed and partially premixed reacting jet-in-crossflow flames at high-pressure (5 atm). This study attempts to expand the data to relatively high pressure and could significantly aid scaling to real gas turbine engine conditions at 20–30 atm. High speed camera, PIV, CH* chemiluminescence, temperature and pressure measurements were taken and processed to allow accurate reconstruction of six operating points relative to CFD simulations under minimal adjustments. Variation of lean main stage (φ = 0.575 and 0.73) and rich jet (φ = 1.1, 4 and 8) equivalence ratio has been investigated for a four mm axial jet. The fully premixed flames were found to be controlled by the crossflow temperature before ignition and the crossflow oxygen content during combustion. Analysis of flame shape and position for the partially premixed operating points describes a lee stabilized as well as a more unsteady windward flame branch. Adjustment of added jet fuel and crossflow temperature along with its corresponding oxygen level is required to attain a compact flame body. The risk of delaying combustion progress is significantly increased at a richer jet φ = 8 and an overshooting, spatially divided flame was attained with a main stage φ = 0.73. Control towards a compact flame body is critical to allow combustion at reasonable reaction rate.


Author(s):  
Marek Malecki ◽  
James Pawley ◽  
Hans Ris

The ultrastructure of cells suspended in physiological fluids or cell culture media can only be studied if the living processes are stopped while the cells remain in suspension. Attachment of living cells to carrier surfaces to facilitate further processing for electron microscopy produces a rapid reorganization of cell structure eradicating most traces of the structures present when the cells were in suspension. The structure of cells in suspension can be immobilized by either chemical fixation or, much faster, by rapid freezing (cryo-immobilization). The fixation speed is particularly important in studies of cell surface reorganization over time. High pressure freezing provides conditions where specimens up to 500μm thick can be frozen in milliseconds without ice crystal damage. This volume is sufficient for cells to remain in suspension until frozen. However, special procedures are needed to assure that the unattached cells are not lost during subsequent processing for LVSEM or HVEM using freeze-substitution or freeze drying. We recently developed such a procedure.


Author(s):  
Robert Corbett ◽  
Delbert E. Philpott ◽  
Sam Black

Observation of subtle or early signs of change in spaceflight induced alterations on living systems require precise methods of sampling. In-flight analysis would be preferable but constraints of time, equipment, personnel and cost dictate the necessity for prolonged storage before retrieval. Because of this, various tissues have been stored in fixatives and combinations of fixatives and observed at various time intervals. High pressure and the effect of buffer alone have also been tried.Of the various tissues embedded, muscle, cartilage and liver, liver has been the most extensively studied because it contains large numbers of organelles common to all tissues (Fig. 1).


Author(s):  
R.E. Crang ◽  
M. Mueller ◽  
K. Zierold

Obtaining frozen-hydrated sections of plant tissues for electron microscopy and microanalysis has been considered difficult, if not impossible, due primarily to the considerable depth of effective freezing in the tissues which would be required. The greatest depth of vitreous freezing is generally considered to be only 15-20 μm in animal specimens. Plant cells are often much larger in diameter and, if several cells are required to be intact, ice crystal damage can be expected to be so severe as to prevent successful cryoultramicrotomy. The very nature of cell walls, intercellular air spaces, irregular topography, and large vacuoles often make it impractical to use immersion, metal-mirror, or jet freezing techniques for botanical material.However, it has been proposed that high-pressure freezing (HPF) may offer an alternative to the more conventional freezing techniques, inasmuch as non-cryoprotected specimens may be frozen in a vitreous, or near-vitreous state, to a radial depth of at least 0.5 mm.


Sign in / Sign up

Export Citation Format

Share Document