SD7003 airfoil in large-scale free stream turbulence

An experimental research program was undertaken to examine the influence of large-scale high-intensity turbulence on vane exit losses, wake growth, and exit turbulence characteristics. The experiment was conducted in a four-vane linear cascade at an exit Reynolds number of 800,000 based on chord length and an exit Mach number of 0.27. Exit measurements were made for four inlet turbulence conditions including a low-turbulence case (Tu ≈ 1 percent), a grid-generated turbulence case (Tu ≈ 7.5. percent) and two levels of large-scale turbulence generated with a mock combustor (Tu ≈ 12 and 8 percent). Exit total pressure surveys were taken at two locations to quantify total pressure losses. The suction surface boundary layer was also traversed to determine losses due to boundary layer growth. Losses occurred in the core of the flow for the elevated turbulence cases. The elevated free-stream turbulence was found to have a significant effect on wake growth. Generally, the wakes subjected to elevated free-stream turbulence were broader and had smaller peak velocity deficits. Reynolds stress profiles exhibited asymmetry in peak amplitudes about the wake centerline, which are attributable to differences in the evolution of the boundary layers on the pressure and suction surfaces of the vanes. The overall level of turbulence and dissipation inside the wakes and in the free stream was determined to document the rotor inlet boundary conditions. This is useful information for assessing rotor heat transfer and aerodynamics. Eddy diffusivities and mixing lengths were estimated using X-wire measurements of turbulent shear stress. The free-stream turbulence was found to strongly affect eddy diffusivities, and thus wake mixing. At the last measuring position, the average eddy diffusivity in the wake of the high-turbulence close combustor configuration (Tu ≈ 12) was three times that of the low turbulence wake.

Download Full-text

Investigation of Various Parametric Influences on Leading Edge Film Cooling

Volume 3: Heat Transfer; Electric Power; Industrial and Cogeneration ◽

10.1115/97-gt-296 ◽

1997 ◽

Cited By ~ 23

Author(s):

Michael W. Cruse ◽

Ushio M. Yuki ◽

David G. Bogard

Keyword(s):

Film Cooling ◽

Large Scale ◽

Free Stream ◽

Density Ratio ◽

Leading Edge ◽

Line Position ◽

Stagnation Line ◽

Free Stream Turbulence ◽

Adiabatic Effectiveness ◽

Density Ratios

Film cooling adiabatic effectiveness of a simulated turbine airfoil leading edge was studied experimentally. The leading edge had two rows of holes, one at nominally the stagnation line position and the second a few hole diameters downstream. Hole positions at the leading edge, and inclination of the holes with respect to the surface, were different than typically used in previous studies, but were representative of current design practice. Various leading edge film cooling parameters were investigated including stagnation line position, free-stream turbulence level, leading edge geometry, and coolant to mainstream density ratio. Large density ratios were obtained by cooling the injected coolant to very low temperatures. Large scale, high level free-stream turbulence (Tu = 20%) was generated using a specially developed cross-jet turbulence generator. An infrared camera system was used to obtain well resolved surface temperature distributions around the coolant holes and across the leading edge. Results from the experiments showed considerably higher optimum blowing ratios than found in previous studies. The stagnation line position was found to be important in influencing the direction of coolant flow from the first row of holes. High free-stream turbulence levels were found to greatly decrease adiabatic effectiveness at low blowing ratios (M = 1.0), but had little effect at high blowing ratios (M = 2.0 and 2.5). Adiabatic effectiveness distributions were very similar for circular and elliptical leading edges. Experiments conducted at coolant to mainstream density ratios of 1.1 and 1.8 showed distinctly different flow characteristics in the stagnation line region for the different density ratio coolants.

Download Full-text

A new boundary layer wind tunnel

The Aeronautical Journal ◽

10.1017/s000192400001616x ◽

1988 ◽

Vol 92 (916) ◽

pp. 224-229

Author(s):

P. E. Roach

Keyword(s):

Boundary Layer ◽

Wind Tunnel ◽

Test Section ◽

Gas Turbines ◽

Large Scale ◽

Free Stream ◽

Boundary Layer Transition ◽

Layer Transition ◽

Free Stream Turbulence ◽

Dimensional Boundary

Summary The procedures employed for the design of a closed-circuit, boundary layer wind tunnel are described. The tunnel was designed for the generation of relatively large-scale, two-dimensional boundary layers with Reynolds numbers, pressure gradients and free-stream turbulence levels typical of the turbomachinery environment. The results of a series of tests to evaluate the tunnel performance are also described. The flow in the test section is shown to be highly uniform and steady, with very low (natural) free-stream turbulence intensities. Measured boundary layer mean and fluctuating velocity profiles were found to be in good agreement with classical correlations. Test-section free-stream turbulence intensities are presented for grid-generated turbulence: agreement with expectation is again found to be good. Immediate applications to the tunnel include friction drag reduction and boundary layer transition studies, with future possibilities including flow separation and other complex flows typical of those found in gas turbines.

Download Full-text

The Influence of Large Scale, High Intensity Turbulence on Vane Aerodynamic Losses, Wake Growth, and the Exit Turbulence Parameters

Volume 1: Turbomachinery ◽

10.1115/95-gt-290 ◽

1995 ◽

Cited By ~ 5

Author(s):

Forrest E. Ames ◽

Michael W. Plesniak

Keyword(s):

Boundary Layer ◽

High Intensity ◽

Total Pressure ◽

Large Scale ◽

Free Stream ◽

Turbulent Shear ◽

Surface Boundary ◽

Suction Surface ◽

Free Stream Turbulence ◽

Eddy Diffusivities

An experimental research program was undertaken to examine the influence of large-scale high, intensity turbulence on vane exit losses, wake growth, and exit turbulence characteristics. The experiment was conducted in a four vane linear cascade at an exit Reynolds number of 800, 000 based on chord length and an exit Mach number of 0.27. Exit measurements were made for four inlet turbulence conditions including a low turbulence case (Tu ≈ 1%), a grid-generated turbulence case (Tu ≈ 7.5%), and two levels of large-scale turbulence generated with a mock combustor (Tu ≈ 12% & Tu ≈ 8%). Exit total pressure surveys were taken at two locations to quantify total pressure losses. The suction surface boundary layer was also traversed to determine losses due boundary layer growth. Losses were also found in the core of the flow for the elevated turbulence cases. The elevated free stream turbulence was found to have a significant effect on wake growth. Generally, the wakes subjected to elevated free stream turbulence were broader and had smaller peak velocity deficits. Reynolds stress profiles exhibited asymmetry in peak amplitudes about the wake centerline, which are attributable to differences in the evolution of the boundary layers on the pressure and suction surfaces of the vanes. The overall level of turbulence and dissipation inside the wakes and in the free stream was determined to document the rotor inlet boundary conditions. This is useful information for assessing rotor heat transfer and aerodynamics. Eddy diffusivities and mixing lengths were estimated using X-wire measurements of turbulent shear stress. The free stream turbulence was found to strongly affect eddy diffusivities, and thus wake mixing. At the last measuring position, the average eddy diffusivity in the wake of the high turbulence close combustor configuration (Tu ≈ 12) was three times that of the low turbulence wake.

Download Full-text

Experimental Investigation of Free Stream Turbulence Effects on Flow Separation

Volume 2: Symposia, Parts A, B, and C ◽

10.1115/fedsm2003-45085 ◽

2003 ◽

Cited By ~ 1

Author(s):

Mahmoud Ardebili ◽

Yiannis Andreopoulos

Keyword(s):

Boundary Layer ◽

Experimental Investigation ◽

Reynolds Number ◽

Pressure Gradient ◽

Flow Separation ◽

Large Scale ◽

Free Stream ◽

Pressure Coefficient ◽

Free Stream Turbulence ◽

Vorticity Flux

An experimental investigation of a separated boundary layer flow has been attempted which has been created by perturbing a flat plate flow with a favorable pressure gradient immediately followed by an adverse pressure gradient. The aim of the research program is possible control of flow separation by means of free stream turbulence. The flow is configured in a large-scale low speed wind tunnel where measurements of turbulence can be obtained with high spatial and temporal resolution. A model has been designed by using CFD analysis. Mean wall pressure and vorticity flux measurements are reported in this paper. Twelve experiments with three different mesh size grids at three different Reynolds numbers have been carried out. Three bulk flow parameters seem to characterize the flow: The Reynolds number of the boundary layer, Re+, the Reynolds number of the flow through the grid, ReM, and the solidity of the grid. It was found that the pressure coefficient depends weakly on the solidity of the grids. Vorticity flux also depends on the grid used to generate free stream turbulence. The location of maximum or minimum vorticity flux moves upstream at higher ReM.

Download Full-text