Correlation and Updating of an Unmanned Aerial Vehicle Finite Element Model

2015 ◽  
Author(s):  
Simone Mezzapesa ◽  
Melissa Arras ◽  
Giuliano Coppotelli ◽  
Jacob Miller ◽  
Daniel N. Valyou ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Unmanned Aerial Vehicle ◽  
Element Model ◽  
Aerial Vehicle

Verification of a Finite Element Model of an Unmanned Aerial Vehicle Wing Torque Box via Experimental Modal Testing

2012 ◽  
Author(s):  
Levent Unlusoy ◽  
Melin Sahin ◽  
Yavuz Yaman
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Unmanned Aerial Vehicle ◽  
Natural Frequencies ◽  
Element Model ◽  
Modal Testing ◽  
Mode Shapes ◽  
Resonance Frequencies ◽  
Aerial Vehicle ◽  
Experimental Modal Testing

In this study, the detailed finite element model (FEM) of an unmanned aerial vehicle wing torque box was verified by the experimental modal testing. During the computational studies the free-free boundary conditions were used and the natural frequencies and mode-shapes of the structure were obtained by using the MSC® Software. The results were then compared with the experimentally obtained resonance frequencies and mode-shapes. It was observed that the frequencies were in close agreement having an error within the range of 1.5–3.6%.

Updating of an Unmanned Aerial Vehicle Finite Element Model using Experimental Data

2015 ◽  
Author(s):  
Melissa Arras ◽  
Giuliano Coppotelli ◽  
Piergiovanni Marzocca ◽  
Antonio Simone Mezzapesa
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Finite Element Model ◽  
Unmanned Aerial Vehicle ◽  
Element Model ◽  
Aerial Vehicle

Finite Element Simulation of Tire-Rim Interface

1989 ◽  
Vol 17 (4) ◽  
pp. 305-325 ◽  
Author(s):  
N. T. Tseng ◽  
R. G. Pelle ◽  
J. P. Chang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Simulation ◽  
Contact Pressure ◽  
Element Model ◽  
Experimental Measurements ◽  
Inflation Pressure ◽  
Interference Fit ◽  
Element Simulation ◽  
Rubber Composite

Abstract A finite element model was developed to simulate the tire-rim interface. Elastomers were modeled by nonlinear incompressible elements, whereas plies were simulated by cord-rubber composite elements. Gap elements were used to simulate the opening between tire and rim at zero inflation pressure. This opening closed when the inflation pressure was increased gradually. The predicted distribution of contact pressure at the tire-rim interface agreed very well with the available experimental measurements. Several variations of the tire-rim interference fit were analyzed.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Sign in / Sign up

Export Citation Format

Share Document