Trailing-Edge Noise Modeling and Validation for Separated Flow Conditions

2013 ◽  
Author(s):  
Chan Yong Schuele ◽  
Karl-Stephane S. Rossignol
Keyword(s):  
Separated Flow ◽  
Flow Conditions ◽  
Trailing Edge ◽  
Trailing Edge Noise ◽  
Noise Modeling

scholarly journals Numerical study of 3-D finlets using Reynolds-averaged Navier–Stokes computational fluid dynamics for trailing edge noise reduction

2020 ◽  
Vol 19 (1-2) ◽  
pp. 95-118 ◽  
Author(s):  
Yuejun Shi ◽  
Seongkyu Lee
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Noise Reduction ◽  
Physical Mechanism ◽  
Navier Stokes ◽  
Flow Conditions ◽  
Trailing Edge ◽  
Trailing Edge Noise ◽  
Reynolds Averaged Navier Stokes ◽  
Spectrum Model

This paper uses Reynolds-averaged Navier–Stokes computational fluid dynamics to study trailing edge noise reduction with 3-D finlets. Reynolds-averaged Navier–Stokes computational fluid dynamics provides boundary layer parameters near a trailing edge for an empirical wall pressure spectrum model, and then an acoustic model predicts far-field noise based on pressure fluctuations obtained from the wall pressure spectrum model. First, this numerical approach is validated against experiments. Second, a comprehensive trend analysis is conducted to give insight into the design of 3-D finlets under different flow conditions. A data-driven turbulence spanwise length scale model is developed to tackle finlets with small spacing. Combined with acoustic results, detailed computational flow field results are analyzed to understand the physical mechanism of noise reduction. While the major part of the proposed mechanism is the same as prior work, several new observations are shown which better understand the physical mechanism of noise reduction with 3-D finlets. The goals of the current paper are to provide an efficient Reynolds-averaged Navier–Stokes-based approach to predict trailing edge noise of 3-D finlets, to give complete trend analysis results with various finlets under different flow conditions, and to advance an understanding of the underlying physics.

Computation of trailing-edge noise due to turbulent flow over an airfoil

AIAA Journal ◽  
2002 ◽  
Vol 40 ◽  
pp. 2206-2216 ◽  
Author(s):  
A. Oberai ◽  
F. Roknaldin ◽  
T. J. R. Hughes
Keyword(s):  
Turbulent Flow ◽  
Trailing Edge ◽  
Trailing Edge Noise

Noise source location and scaling of subsonic upper-surface blowing

2020 ◽  
Vol 19 (3-5) ◽  
pp. 191-206
Author(s):  
Trae L Jennette ◽  
Krish K Ahuja
Keyword(s):  
Strouhal Number ◽  
Noise Source ◽  
Low Frequency ◽  
Directivity Pattern ◽  
Source Location ◽  
Dipole Source ◽  
Frequency Noise ◽  
Noise Sources ◽  
Trailing Edge ◽  
Trailing Edge Noise

This paper deals with the topic of upper surface blowing noise. Using a model-scale rectangular nozzle of an aspect ratio of 10 and a sharp trailing edge, detailed noise contours were acquired with and without a subsonic jet blowing over a flat surface to determine the noise source location as a function of frequency. Additionally, velocity scaling of the upper surface blowing noise was carried out. It was found that the upper surface blowing increases the noise significantly. This is a result of both the trailing edge noise and turbulence downstream of the trailing edge, referred to as wake noise in the paper. It was found that low-frequency noise with a peak Strouhal number of 0.02 originates from the trailing edge whereas the high-frequency noise with the peak in the vicinity of Strouhal number of 0.2 originates near the nozzle exit. Low frequency (low Strouhal number) follows a velocity scaling corresponding to a dipole source where as the high Strouhal numbers as quadrupole sources. The culmination of these two effects is a cardioid-shaped directivity pattern. On the shielded side, the most dominant noise sources were at the trailing edge and in the near wake. The trailing edge mounting geometry also created anomalous acoustic diffraction indicating that not only is the geometry of the edge itself important, but also all geometry near the trailing edge.

Three-Dimensional and Rotational Aerodynamics on the NREL Phase VI Wind Turbine Blade

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Alvaro Gonzalez ◽  
Xabier Munduate
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Three Dimensional ◽  
Separated Flow ◽  
Leading Edge ◽  
Wind Turbine Blade ◽  
Trailing Edge ◽  
Rotating Blade ◽  
Nrel Phase Vi ◽  
Edge Separation

This work undertakes an aerodynamic analysis over the parked and the rotating NREL Phase VI wind turbine blade. The experimental sequences from NASA Ames wind tunnel selected for this study respond to the parked blade and the rotating configuration, both for the upwind, two-bladed wind turbine operating at nonyawed conditions. The objective is to bring some light into the nature of the flow field and especially the type of stall behavior observed when 2D aerofoil steady measurements are compared to the parked blade and the latter to the rotating one. From averaged pressure coefficients together with their standard deviation values, trailing and leading edge separated flow regions have been found, with the limitations of the repeatability of the flow encountered on the blade. Results for the parked blade show the progressive delay from tip to root of the trailing edge separation process, with respect to the 2D profile, and also reveal a local region of leading edge separated flow or bubble at the inner, 30% and 47% of the blade. For the rotating blade, results at inboard 30% and 47% stations show a dramatic suppression of the trailing edge separation, and the development of a leading edge separation structure connected with the extra lift.

Sign in / Sign up

Export Citation Format

Share Document