scholarly journals Suppression of Vortex Shedding from a Circular Cylinder by using a Suction Flow Control Method

2013 ◽  
Author(s):  
Hui Hu ◽  
Wenli Chen ◽  
Hui Li
Keyword(s):  
Circular Cylinder ◽  
Flow Control ◽  
Vortex Shedding ◽  
Control Method ◽  
Suction Flow

Passive Jet Flow Control Method for Suppressing Unsteady Vortex Shedding from a Circular Cylinder

2017 ◽  
Vol 30 (1) ◽  
pp. 04016063 ◽  
Author(s):  
Wen-Li Chen ◽  
Xiangjun Wang ◽  
Feng Xu ◽  
Hui Li ◽  
Hui Hu
Keyword(s):  
Circular Cylinder ◽  
Flow Control ◽  
Vortex Shedding ◽  
Control Method ◽  
Jet Flow

Suppression of Unsteady Vortex Shedding From a Circular Cylinder by Using a Passive Jet Flow Control Method

2014 ◽  
Author(s):  
Wenli Chen ◽  
Hui Li ◽  
Hui Hu
Keyword(s):  
Circular Cylinder ◽  
Flow Control ◽  
Stagnation Point ◽  
Vortex Shedding ◽  
Control Method ◽  
Aerodynamic Force ◽  
Jet Flow ◽  
Wake Flow ◽  
Cylinder Model ◽  
Rear Stagnation Point

A passive jet flow control method was employed to suppress the unsteady vortex shedding from a circular cylinder at the Reynolds number level of Re = (0.18∼1.1)×105. The passive jet flow control was achieved by blowing jets from the holes near the rear stagnation point of the cylinder, which are connected to the in-take holes located near the front stagnation point through channels embedded inside the cylinder. Since a part of the oncoming flow would inhale into the in-take holes, flow through the embedded channels, and blow out from the holes near the rear stagnation point to suppress/manipulate the alternating vortex shedding in the wake flow behind the circular cylinder, the present passive jet flow control method does not require any additional energy inputs for the flow control. In the present study, the aerodynamic force (i.e., both lift and drag) acting the circular cylinder model with and without the passive jet flow control were compared quantitatively at different Reynolds numbers (i.e., different inlet mean speed). It was found that, in addition to almost eliminating the fluctuations of the lift forces acting on the cylinder, the passive jet flow control method was also found to reduce the mean drag acting on the cylinder model greatly. The instantaneous vorticity distributions and corresponding streamline patterns were used to reveal the underlying physics about why and how the passive jet flow control method can be used to suppress the alternating vortex shedding and induce a symmetrical wake pattern behind the cylinder model.

scholarly journals Effect of Cylinder Gap Ratio on The Wake of a Circular Cylinder Enclosed by Various Perforated Shrouds

CFD letters ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 51-68
Author(s):  
Nurul Azihan Ramli ◽  
Azlin Mohd Azmi ◽  
Ahmad Hussein Abdul Hamid ◽  
Zainal Abidin Kamarul Baharin ◽  
Tongming Zhou
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Vortex Shedding ◽  
Control Method ◽  
Lift Coefficient ◽  
Base Case ◽  
Bluff Bodies ◽  
Ansys Fluent ◽  
Gap Ratio ◽  
Spacing Ratio

Flow over bluff bodies produces vortex shedding in their wake regions, leading to structural failure from the flow-induced forces. In this study, a passive flow control method was explored to suppress the vortex shedding from a circular cylinder that causes many problems in engineering applications. Perforated shrouds were used to control the vortex shedding of a circular cylinder at Reynolds number, Re = 200. The shrouds were of non-uniform and uniform holes with 67% porosity. The spacing gap ratio between the shroud and the cylinder was set at 1.2, 1.5, 2, and 2.2. The analysis was conducted using ANSYS Fluent using a viscous laminar model. The outcomes of the simulation of the base case were validated with existing studies. The drag coefficient, Cd, lift coefficient, Cl and the Strouhal number, St, as well as vorticity contours, velocity contours, and pressure contours were examined. Vortex shedding behind the shrouded cylinders was observed to be suppressed and delayed farther downstream with increasing gap ratio. The effect was significant for spacing ratio greater than 2.0. The effect of hole types: uniform and non-uniform holes, was also effective at these spacing ratios for the chosen Reynolds number of 200. Specifically, a spacing ratio of 1.2 enhanced further the vortex intensity and should be avoided.

Control of Vortex Shedding Using a Screen Attached on the Separation Point of a Circular Cylinder and Its Effect on Drag

2017 ◽  
Vol 139 (7) ◽  
Author(s):  
Gokturk Memduh Ozkan ◽  
Erhan Firat ◽  
Huseyin Akilli
Keyword(s):  
Circular Cylinder ◽  
Surface Area ◽  
Vortex Shedding ◽  
Control Method ◽  
Separation Point ◽  
Whole Body ◽  
Cylinder Surface ◽  
Control Effect ◽  
Permeable Plate ◽  
Turbulent Statistics

The control of flow in the wake of a circular cylinder by an attached permeable plate having various porosity ratios was analyzed experimentally using both particle image velocimetry (PIV) and dye visualization techniques. The force measurements were also done in order to interpret the effect of control method on drag coefficient. The diameter of the cylinder and length to diameter ratio of the plate were kept constant as D = 50 mm and L/D = 1.0, respectively. The porosity ratio, β, which can be defined as the ratio of open surface area to the whole body surface area, was taken as β = 0.4, 0.5, 0.6, 0.7, and 0.8 (permeable plates). The study was performed considering deep water flow conditions with a constant Reynolds number of ReD = 5000 based on the cylinder diameter. Each permeable plate was attached on the separation point and the results were compared with the results of cylinder without permeable plate (plain cylinder) in order to understand the control effect. Both qualitative and quantitative results revealed that the permeable plates of 0.4 ≤ β ≤ 0.6 are effective on controlling the unsteady flow structure downstream of the cylinder, i.e., the vortex formation length was increased, turbulent statistics was reduced and vortex shedding frequency was diminished when the permeable plate attached normal to the cylinder surface from the lower separation point. However, the drag force acting on the cylinder was found to be increased due to the increased cross-sectional area.

Suppression of Vortex Shedding Downstream of a Circular Cylinder Using Permeable Cylinders in Shallow Water

2013 ◽  
Author(s):  
Göktürk Memduh Özkan ◽  
Hüseyin Akıllı
Keyword(s):  
Circular Cylinder ◽  
Flow Control ◽  
Shallow Water ◽  
Flow Structure ◽  
Vortex Shedding ◽  
Outer Cylinder ◽  
Vortex Formation ◽  
Stream Velocity ◽  
Bluff Bodies ◽  
Different Diameters

The characteristics of the flow around a 50mm circular cylinder surrounded by a permeable outer cylinder were investigated by Particle Image Velocimetry (PIV) and flow visualization techniques in order to control the unsteady flow structure downstream of the cylinder in shallow water. The effect of outer permeable cylinder with a porosity of β = 0.4 on the flow control was studied using five different diameters; D = 60, 70, 80, 90, 100mm. Depth-averaged free stream velocity was kept constant as U = 170mm/s corresponding to a Reynolds number of Re = 8500 and the water height was adjusted to hw = 25mm throughout the study. The results clearly showed that the outer permeable cylinder significantly affects the flow structure of the inner cylinder. It was found that by the existence of outer cylinder, the frequency of unsteady vortex shedding is reduced, vortex formation region is elongated and fluctuations are attenuated which are good indications of effective flow control. Owing to the results, optimum parameters were defined and suggested for the suppression of vortex-induced vibrations on bluff bodies.

scholarly journals Novel Flow Control Method for Vortex Shedding of Turbine Blade

2010 ◽  
Vol 53 (180) ◽  
pp. 122-129 ◽  
Author(s):  
Mahmoud M. EL-GENDI ◽  
Mohammed K. IBRAHIM ◽  
Koichi MORI ◽  
Yoshiaki NAKAMURA
Keyword(s):  
Flow Control ◽  
Turbine Blade ◽  
Vortex Shedding ◽  
Control Method

CONTROL OF VORTEX SHEDDING BEHIND A CIRCULAR CYLINDER USING ELECTROMAGNETIC FORCES

2005 ◽  
Vol 19 (28n29) ◽  
pp. 1627-1630 ◽  
Author(s):  
ZHIHUA CHEN ◽  
BAOCHUN FAN ◽  
BENMOU ZHOU ◽  
NADINE AUBRY
Keyword(s):  
Circular Cylinder ◽  
Lorentz Force ◽  
Vortex Shedding ◽  
Closed Loop ◽  
Permanent Magnets ◽  
Control Method ◽  
The Body ◽  
Closed Loop Control ◽  
Electromagnetic Forces ◽  
Loop Control

Both open and closed loop control algorithms have been developed for manipulating wake flows past a solid cylinder in an electrically low-conducting fluid. The intent is to avoid vortex shedding and flow separation from the body, which is achieved through the introduction of localized electromagnetic forces (Lorentz forces) in the azimuthal direction generated by an array of permanent magnets and electrodes on the surface of the circular cylinder. The array of actuators offers the advantage of making the Lorentz force time and space dependent. More specifically, one closed loop control method has been derived from the equations of motion capable of determining at all times the intensity of the Lorentz force in order to control the flow. This is accomplished first, independently of the flow (open loop algorithm) and second, based on some partial flow information measured on the surface of the solid body (closed loop algorithm).

Sign in / Sign up

Export Citation Format

Share Document