Force Measurements in Hypervelocity Flows with an Acceleration Compensated Strain Gage Balance

2011 ◽  
Author(s):  
Eric Marineau ◽  
Matthew Maclean ◽  
Erik Mundy ◽  
Michael Holden
Keyword(s):  
Strain Gage ◽  
Force Measurements ◽  
Hypervelocity Flows

Force Measurements in Hypervelocity Flows with an Acceleration Compensated Strain Gage Balance

2012 ◽  
Vol 49 (3) ◽  
pp. 474-482 ◽  
Author(s):  
Eric C. Marineau ◽  
Matthew MacLean ◽  
Erik P. Mundy ◽  
Michael S. Holden
Keyword(s):  
Strain Gage ◽  
Force Measurements ◽  
Hypervelocity Flows

Cord Force Measurements in Radial Tires

1972 ◽  
Vol 94 (2) ◽  
pp. 678-682 ◽  
Author(s):  
J. D. Walter
Keyword(s):  
Strain Gage ◽  
Simple Formula ◽  
Rubber Matrix ◽  
Force Measurements ◽  
Inflation Pressure ◽  
Force Transducers ◽  
In Series ◽  
Straight Ahead ◽  
Automobile Tires

Miniature force transducers in the form of strain gage instrumented tension links are used to measure the loads developed in the rayon cords in both the stabilizer and body plies of automobile tires of radial construction. These transducers are placed in series with the cord and are embedded in the rubber matrix of the tire during building. Cord forces are obtained at various wheel loads and inflation pressures for straight ahead rolling and cornering of the tires in operation. It is shown that a relatively simple formula can be used to theoretically predict the cord tension developed in the sidewall region due to inflation pressure.

The Fluidic Load Cell

1974 ◽  
Vol 96 (3) ◽  
pp. 358-360
Author(s):  
Tadeusz M. Drzewiecki
Keyword(s):  
Strain Gage ◽  
Dynamic Range ◽  
Compressive Load ◽  
Load Cell ◽  
Force Measurements ◽  
Output Pressure ◽  
Through Flow ◽  
Load Cells ◽  
Amplifier Gain ◽  
Fluidic Resistance

A possible fluidic load cell design consists of three parts: a structural member that deforms linearly with load, a fluidic strain gage having fluidic resistance that changes with deformation, and a three-stage laminar proportional amplifier-gain block that amplifies the change in strain gage through-flow to useful levels. This Technical Brief presents design relations for the first two parts of such a system. Two compressive load cells were built, incorporating different fabrication techniques and deformation-sensing methods. The loading range of these cells is about 0 to 20 kN (0 to 2 tons) with a dynamic range greater than 100 and a typical full-scale output pressure of 30 pascals (4 × 10−3 psi). Possible applications for fluidic load cells include force measurements in highly incendiary or radiative environments and/or when other fluid control circuitry is used.

A strain-gage platform for force measurements

1965 ◽  
Vol 20 (5) ◽  
pp. 1095-1097 ◽  
Author(s):  
W. A. Petersen ◽  
J. M. Brookhart ◽  
Solon A. Stone
Keyword(s):  
Strain Gage ◽  
Force Measurement ◽  
Mass Measurement ◽  
Force Transducer ◽  
Strain Gages ◽  
Force Measurements ◽  
Weight Measurement ◽  
Linear Force ◽  
And Performance ◽  
Design Construction

Design, construction and performance characteristics are described for a rugged, compact, linear force transducer using strain gages as the sensing elements. The device is adaptable to a variety of weighing or force-measurement tasks in the laboratory. weight measurement; mass measurement; force transducer; weight transducer; load cell Submitted on November 13, 1964

A miniature strain-gage balance for hypersonic force measurements

AIAA Journal ◽  
1965 ◽  
Vol 3 (4) ◽  
pp. 793-794
Author(s):  
EUGENE V. HORANOFF ◽  
BING H. LIEU
Keyword(s):  
Strain Gage ◽  
Force Measurements
Sign in / Sign up

Export Citation Format

Share Document