Leading Edge Vortex Development on a Waving Wing at Reynolds Numbers Between 10,000 and 60,000

2011 ◽  
Author(s):  
Anya Jones ◽  
Holger Babinsky
Keyword(s):  
Leading Edge ◽  
Reynolds Numbers ◽  
Leading Edge Vortex ◽  
Edge Vortex

Heat Transfer and Flowfield Measurements in the Leading Edge Region of a Stator Vane Endwall

1999 ◽  
Vol 121 (3) ◽  
pp. 558-568 ◽  
Author(s):  
M. B. Kang ◽  
A. Kohli ◽  
K. A. Thole
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Edge Region ◽  
Leading Edge Vortex ◽  
Stator Vane ◽  
Edge Vortex ◽  
The Mean

The leading edge region of a first-stage stator vane experiences high heat transfer rates, especially near the endwall, making it very important to get a better understanding of the formation of the leading edge vortex. In order to improve numerical predictions of the complex endwall flow, benchmark quality experimental data are required. To this purpose, this study documents the endwall heat transfer and static pressure coefficient distribution of a modern stator vane for two different exit Reynolds numbers (Reex = 6 × 105 and 1.2 × 106). In addition, laser-Doppler velocimeter measurements of all three components of the mean and fluctuating velocities are presented for a plane in the leading edge region. Results indicate that the endwall heat transfer, pressure distribution, and flowfield characteristics change with Reynolds number. The endwall pressure distributions show that lower pressure coefficients occur at higher Reynolds numbers due to secondary flows. The stronger secondary flows cause enhanced heat transfer near the trailing edge of the vane at the higher Reynolds number. On the other hand, the mean velocity, turbulent kinetic energy, and vorticity results indicate that leading edge vortex is stronger and more turbulent at the lower Reynolds number. The Reynolds number also has an effect on the location of the separation point, which moves closer to the stator vane at lower Reynolds numbers.

The leading-edge vortex and aerodynamics of insect-based flapping-wing micro air vehicles

2009 ◽  
Vol 113 (1142) ◽  
pp. 253-262 ◽  
Author(s):  
P. C. Wilkins ◽  
K. Knowles
Keyword(s):  
Entire Range ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Micro Air Vehicles ◽  
Reynolds Numbers ◽  
Flapping Wing ◽  
Computational Method ◽  
Leading Edge Vortex ◽  
Air Vehicle ◽  
Edge Vortex

AbstractThe aerodynamics of insect-like flapping are dominated by the production of a large, stable, and lift-enhancing leading-edge vortex (LEV) above the wing. In this paper the phenomenology behind the LEV is explored, the reasons for its stability are investigated, and the effects on the LEV of changing Reynolds number or angle-of-attack are studied. A predominantly-computational method has been used, validated against both existing and new experimental data. It is concluded that the LEV is stable over the entire range of Reynolds numbers investigated here and that changes in angle-of-attack do not affect the LEV’s stability. The primary motivation of the current work is to ascertain whether insect-like flapping can be successfully ‘scaled up’ to produce a flapping-wing micro air vehicle (FMAV) and the results presented here suggest that this should be the case.

The role of advance ratio and aspect ratio in determining leading-edge vortex stability for flapping flight

2014 ◽  
Vol 751 ◽  
pp. 71-105 ◽  
Author(s):  
R. R. Harbig ◽  
J. Sheridan ◽  
M. C. Thompson
Keyword(s):  
Aspect Ratio ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Leading Edge Vortex ◽  
Aspect Ratios ◽  
Edge Vortex ◽  
Advance Ratio ◽  
Vorticity Production ◽  
The Stability

AbstractThe effects of advance ratio and the wing’s aspect ratio on the structure of the leading-edge vortex (LEV) that forms on flapping and rotating wings under insect-like flight conditions are not well understood. However, recent studies have indicated that they could play a role in determining the stable attachment of the LEV. In this study, a numerical model of a flapping wing at insect Reynolds numbers is used to explore the effects of these parameters on the characteristics and stability of the LEV. The word ‘stability’ is used here to describe whether the LEV was attached throughout the stroke or if it was shed. It is demonstrated that increasing the advance ratio enhances vorticity production at the leading edge during the downstroke, and this results in more rapid growth of the LEV for non-zero advance ratios. Increasing the wing aspect ratio was found to have the effect of shortening the wing’s chord length relative to the LEV’s size. These two effects combined determine the stability of the LEV. For high advance ratios and large aspect ratios, the LEV was observed to quickly grow to envelop the entire wing during the early stages of the downstroke. Continued rotation of the wing resulted in the LEV being eventually shed as part of a vortex loop that peels away from the wing’s tip. The shedding of the LEV for high-aspect-ratio wings at non-zero advance ratios leads to reduced aerodynamic performance of these wings, which helps to explain why a number of insect species have evolved to have low-aspect-ratio wings.

scholarly journals UNSTEADY AERODYNAMIC PERFORMANCE OF MODEL WINGS AT LOW REYNOLDS NUMBERS

1993 ◽  
Vol 174 (1) ◽  
pp. 45-64 ◽  
Author(s):  
M. H. Dickinson ◽  
K. G. Gotz
Keyword(s):  
Insect Flight ◽  
Delta Wing ◽  
Force Production ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Aerodynamic Forces ◽  
Trailing Edge ◽  
Leading Edge Vortex ◽  
Precise Knowledge ◽  
Edge Vortex

The synthesis of a comprehensive theory of force production in insect flight is hindered in part by the lack of precise knowledge of unsteady forces produced by wings. Data are especially sparse in the intermediate Reynolds number regime (10<Re<1000) appropriate for the flight of small insects. This paper attempts to fill this deficit by quantifying the time-dependence of aerodynamic forces for a simple yet important motion, rapid acceleration from rest to a constant velocity at a fixed angle of attack. The study couples the measurement of lift and drag on a two-dimensional model with simultaneous flow visualization. The results of these experiments are summarized below. 1. At angles of attack below 13.5°, there was virtually no evidence of a delay in the generation of lift, in contrast to similar studies made at higher Reynolds numbers. 2. At angles of attack above 13.5°, impulsive movement resulted in the production of a leading edge vortex that stayed attached to the wing for the first 2 chord lengths of travel, resulting in an 80 % increase in lift compared to the performance measured 5 chord lengths later. It is argued that this increase is due to the process of detached vortex lift, analogous to the method of force production in delta-wing aircraft. 3. As the initial leading edge vortex is shed from the wing, a second vortex of opposite vorticity develops from the trailing edge of the wing, correlating with a decrease in lift production. This pattern of alternating leading and trailing edge vortices generates a von Karman street, which is stable for at least 7.5 chord lengths of travel. 4. Throughout the first 7.5 chords of travel the model wing exhibits a broad lift plateau at angles of attack up to 54°, which is not significantly altered by the addition of wing camber or surface projections. 5. Taken together, these results indicate how the unsteady process of vortex generation at large angles of attack might contribute to the production of aerodynamic forces in insect flight. Because the fly wing typically moves only 2–4 chord lengths each half-stroke, the complex dynamic behavior of impulsively started wing profiles is more appropriate for models of insect flight than are steady-state approximations.

Flight

2018 ◽  
Author(s):  
Anders Hedenström
Keyword(s):  
Bird Species ◽  
Leading Edge ◽  
Micro Air Vehicles ◽  
Leading Edge Vortex ◽  
Confined Spaces ◽  
Unsteady Aerodynamic ◽  
Maneuvering Flight ◽  
Edge Vortex ◽  
Lifting Surfaces ◽  
Animal Flight

Animal flight represents a great challenge and model for biomimetic design efforts. Powered flight at low speeds requires not only appropriate lifting surfaces (wings) and actuator (engine), but also an advanced sensory control system to allow maneuvering in confined spaces, and take-off and landing. Millions of years of evolutionary tinkering has resulted in modern birds and bats, which are achieve controlled maneuvering flight as well as hovering and cruising flight with trans-continental non-stop migratory flights enduring several days in some bird species. Unsteady aerodynamic mechanisms allows for hovering and slow flight in insects, birds and bats, such as for example the delayed stall with a leading edge vortex used to enhance lift at slows speeds. By studying animal flight with the aim of mimicking key adaptations allowing flight as found in animals, engineers will be able to design micro air vehicles of similar capacities.

Flow criticality governs leading-edge-vortex initiation on finite wings in unsteady flow

2021 ◽  
Vol 910 ◽  
Author(s):  
Yoshikazu Hirato ◽  
Minao Shen ◽  
Ashok Gopalarathnam ◽  
Jack R. Edwards
Keyword(s):  
Unsteady Flow ◽  
Leading Edge ◽  
Leading Edge Vortex ◽  
Edge Vortex

Abstract

Vorticity transport in the leading-edge vortex on a rotating blade

2014 ◽  
Vol 743 ◽  
pp. 249-261 ◽  
Author(s):  
Craig J. Wojcik ◽  
James H. J. Buchholz
Keyword(s):  
Leading Edge ◽  
Quasi Equilibrium ◽  
Transport Mechanisms ◽  
Leading Edge Vortex ◽  
Rotating Blade ◽  
Edge Vortex ◽  
Rotation Motion ◽  
Vorticity Transport ◽  
Control Volumes ◽  
Quiescent Fluid

AbstractVorticity transport is analysed within the leading-edge vortex generated on a rectangular flat plate of aspect ratio 4 undergoing a starting rotation motion in a quiescent fluid. Two analyses are conducted on the inboard half of the blade to better understand the vorticity transport mechanisms responsible for maintaining the quasi-equilibrium state of the leading-edge vortex. An initial global analysis between the $25$ and $50\, \%$ spanwise positions suggests that, although spanwise velocity is significant, spanwise convection of vorticity is insufficient to balance the flux of vorticity from the leading-edge shear layer. Subsequent detailed analyses of vorticity transport in planar control volumes at the $25$ and $50\, \%$ spanwise positions verify this conclusion and demonstrate that vorticity annihilation due to interaction between the leading-edge vortex and the opposite-sign layer on the plate surface is an important, often dominant, mechanism for regulation of leading-edge-vortex circulation. Thus, it provides an important condition for maintenance of an attached leading-edge vortex on the inboard portion of the blade.

Sign in / Sign up

Export Citation Format

Share Document