A-posteriori testing of numerical simulations using dissipation elements

2011 ◽  
Author(s):  
Michael Gauding ◽  
Philip Schaefer ◽  
Markus Gampert ◽  
Norbert Peters
Keyword(s):  
Numerical Simulations ◽  
A Posteriori ◽  
Dissipation Elements

Practical Correction of Three Fold Astigmatism in the Philips CM TEM

1996 ◽  
Vol 54 ◽  
pp. 418-419
Author(s):  
Arno J. Bleeker ◽  
Mark H.F. Overwijk ◽  
Max T. Otten
Keyword(s):  
Optical Properties ◽  
Phase Contrast ◽  
The Other ◽  
Objective Lens ◽  
Symmetric Part ◽  
A Posteriori ◽  
Contrast Transfer Function ◽  
High Brightness ◽  
Rotationally Symmetric ◽  
Brightness Field

With the improvement of the optical properties of the modern TEM objective lenses the point resolution is pushed beyond 0.2 nm. The objective lens of the CM300 UltraTwin combines a Cs of 0. 65 mm with a Cc of 1.4 mm. At 300 kV this results in a point resolution of 0.17 nm. Together with a high-brightness field-emission gun with an energy spread of 0.8 eV the information limit is pushed down to 0.1 nm. The rotationally symmetric part of the phase contrast transfer function (pctf), whose first zero at Scherzer focus determines the point resolution, is mainly determined by the Cs and defocus. Apart from the rotationally symmetric part there is also the non-rotationally symmetric part of the pctf. Here the main contributors are not only two-fold astigmatism and beam tilt but also three-fold astigmatism. The two-fold astigmatism together with the beam tilt can be corrected in a straight-forward way using the coma-free alignment and the objective stigmator. However, this only works well when the coefficient of three-fold astigmatism is negligible compared to the other aberration coefficients. Unfortunately this is not generally the case with the modern high-resolution objective lenses. Measurements done at a CM300 SuperTwin FEG showed a three fold-astigmatism of 1100 nm which is consistent with measurements done by others. A three-fold astigmatism of 1000 nm already sinificantly influences the image at a spatial frequency corresponding to 0.2 nm which is even above the point resolution of the objective lens. In principle it is possible to correct for the three-fold astigmatism a posteriori when through-focus series are taken or when off-axis holography is employed. This is, however not possible for single images. The only possibility is then to correct for the three-fold astigmatism in the microscope by the addition of a hexapole corrector near the objective lens.

Expected A Posteriori Estimation of Multiple Latent Traits

2005 ◽  
Author(s):  
Damon U. Bryant ◽  
Ashley K. Smith ◽  
Sandra G. Alexander ◽  
Kathlea Vaughn ◽  
Kristophor G. Canali
Keyword(s):  
A Posteriori ◽  
Latent Traits ◽  
Posteriori Estimation

Saturation mechanism and generated viscosity in gravito-turbulent accretion disks

2020 ◽  
Vol 640 ◽  
pp. A53
Author(s):  
L. Löhnert ◽  
S. Krätschmer ◽  
A. G. Peeters
Keyword(s):  
Growth Rate ◽  
Numerical Simulations ◽  
Accretion Disks ◽  
Gravitational Instability ◽  
Turbulent Viscosity ◽  
Radial Distance ◽  
Maximum Growth ◽  
Wave Number ◽  
Radiative Cooling ◽  
Mixing Length

Here, we address the turbulent dynamics of the gravitational instability in accretion disks, retaining both radiative cooling and irradiation. Due to radiative cooling, the disk is unstable for all values of the Toomre parameter, and an accurate estimate of the maximum growth rate is derived analytically. A detailed study of the turbulent spectra shows a rapid decay with an azimuthal wave number stronger than ky−3, whereas the spectrum is more broad in the radial direction and shows a scaling in the range kx−3 to kx−2. The radial component of the radial velocity profile consists of a superposition of shocks of different heights, and is similar to that found in Burgers’ turbulence. Assuming saturation occurs through nonlinear wave steepening leading to shock formation, we developed a mixing-length model in which the typical length scale is related to the average radial distance between shocks. Furthermore, since the numerical simulations show that linear drive is necessary in order to sustain turbulence, we used the growth rate of the most unstable mode to estimate the typical timescale. The mixing-length model that was obtained agrees well with numerical simulations. The model gives an analytic expression for the turbulent viscosity as a function of the Toomre parameter and cooling time. It predicts that relevant values of α = 10−3 can be obtained in disks that have a Toomre parameter as high as Q ≈ 10.

CHARACTERIZATION OF SPLASH-PLATE ATOMIZERS USING NUMERICAL SIMULATIONS

2007 ◽  
Vol 17 (4) ◽  
pp. 347-380 ◽  
Author(s):  
Mohammad P. Fard ◽  
Denise Levesque ◽  
Stuart Morrison ◽  
Nasser Ashgriz ◽  
J. Mostaghimi
Keyword(s):  
Numerical Simulations
Sign in / Sign up

Export Citation Format

Share Document