Experimental Characterization of an Integrated Flow Control Method with Blowing and DBD Plasma Actuator

2011 ◽  
Author(s):  
Muhammad Baqui ◽  
Zakaria Mahmud
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Plasma Actuator ◽  
Experimental Characterization ◽  
Dbd Plasma

Experimental Analysis of Closed-Loop Flow Control Around Airfoil Using DBD Plasma Actuator

2017 ◽  
Author(s):  
Satoshi Shimomura ◽  
Takuto Ogawa ◽  
Satoshi Sekimoto ◽  
Taku Nonomura ◽  
Akira Oyama ◽  
...  
Keyword(s):  
Flow Control ◽  
Pressure Fluctuation ◽  
Closed Loop ◽  
Control Method ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Plasma Actuator ◽  
Chord Length ◽  
Dbd Plasma ◽  
Attached Flow

This paper experimentally investigates the effectiveness of a closed-loop flow control method using a DBD plasma actuator for a NACA0015 airfoil, in which the surface pressure fluctuation is fed back to the system; the actuator was driven when the pressure fluctuation exceeds the setup threshold. The Reynolds number based on the chord length is set to 63,000 and the angle of attack is in the range from 12 to 15 degrees. The actuator was installed on the surface at 5% of the chord length from the leading edge. The results show that the closed-loop control worked better than the continuous operation. In the angle of attack of 12 and 14 degrees, the complete attached flow was attained by setting the appropriate threshold value of the pressure fluctuation. On the other hand, in 15 degrees, although the complete attached flow was not attained, the flow separation was partially suppressed.

Dual-position excitation technique in flow control over an airfoil at low speeds

2018 ◽  
Vol 30 (9) ◽  
pp. 4141-4154
Author(s):  
Abbas Ebrahimi ◽  
Majid Hajipour ◽  
Kamran Ghamkhar
Keyword(s):  
Flow Control ◽  
Shear Layer ◽  
Control Method ◽  
Lift Coefficient ◽  
Shear Layers ◽  
Control Flow ◽  
Plasma Actuators ◽  
Dbd Plasma ◽  
Surface Shear ◽  
Content Type

PurposeThe purpose of this paper is to control flow separation over a NACA 4415 airfoil by applying unsteady forces to the separated shear layers using dielectric barrier discharge (DBD) plasma actuators. This novel flow control method is studied under conditions which the airfoil angle of attack is 18°, and Reynolds number based on chord length is 5.5 × 105.Design/methodology/approachLarge eddy simulation of the turbulent flow is used to capture vortical structures through the airfoil wake. Power spectral density analysis of the baseline flow indicates dominant natural frequencies associated with “shear layer mode” and “wake mode.” The wake mode frequency is used simultaneously to excite separated shear layers at both the upper surface and the trailing edge of the airfoil (dual-position excitation), and it is also used singly to excite the upper surface shear layer (single-position excitation).FindingsBased on the results, actuations manipulate the shear layers instabilities and change the wake patterns considerably. It is revealed that in the single-position excitation case, the vortices shed from the upper surface shear layer are more coherent than the dual-position excitation case. The maximum value of lift coefficient and lift-to-drag ratio is achieved, respectively, by single-position excitation as well as dual-position excitation.Originality/valueThe paper contributes to the understanding and progress of DBD plasma actuators for flow control applications. Further, this research could be a beneficial solution for the promising design of advanced low speed flying vehicles.

scholarly journals Experimental Characterization of a Novel Cyclotronic Plasma Actuator

AIAA Journal ◽  
2020 ◽  
Vol 58 (2) ◽  
pp. 747-756
Author(s):  
Georgi K. Hristov ◽  
Phillip J. Ansell ◽  
Joseph W. Zimmerman ◽  
David L. Carroll
Keyword(s):  
Plasma Actuator ◽  
Experimental Characterization

scholarly journals Coherent structures induced by dielectric barrier discharge plasma actuator

2017 ◽  
Vol 31 (32) ◽  
pp. 1850038 ◽  
Author(s):  
Xin Zhang ◽  
Huaxing Li ◽  
Kwing So Choi ◽  
Longfei Song
Keyword(s):  
Flow Control ◽  
Dielectric Barrier Discharge ◽  
Coherent Structures ◽  
High Speed ◽  
Barrier Discharge ◽  
Plasma Actuator ◽  
Dbd Plasma ◽  
Peak Voltage ◽  
Dielectric Barrier ◽  
Piv Measurement

The structures of a flow field induced by a plasma actuator were investigated experimentally in quiescent air using high-speed Particle Image Velocimetry (PIV) technology. The motivation behind was to figure out the flow control mechanism of the plasma technique. A symmetrical Dielectric Barrier Discharge (DBD) plasma actuator was mounted on the suction side of the SC (2)-0714 supercritical airfoil. The results demonstrated that the plasma jet had some coherent structures in the separated shear layer and these structures were linked to a dominant frequency of [Formula: see text] = 39 Hz when the peak-to-peak voltage of plasma actuator was 9.8 kV. The high speed PIV measurement of the induced airflow suggested that the plasma actuator could excite the flow instabilities which lead to production of the roll-up vortex. Analysis of transient results indicated that the roll-up vortices had the process of formation, movement, merging and breakdown. This could promote the entrainment effect of plasma actuator between the outside airflow and boundary layer flow, which is very important for flow control applications.

Flow Control on a Transport Truck Side Mirror Using Plasma Actuators

2015 ◽  
Vol 137 (11) ◽  
Author(s):  
Theodoros Michelis ◽  
Marios Kotsonis
Keyword(s):  
Flow Control ◽  
Guide Vane ◽  
Leading Edge ◽  
Plasma Actuator ◽  
Plasma Actuators ◽  
Dbd Plasma ◽  
Reference Case ◽  
Image Velocimetry ◽  
Wind Tunnel Study ◽  
Edge Separation

A wind tunnel study is conducted toward hybrid flow control of a full scale transport truck side mirror at ReD=3.2×105. A slim guide vane is employed for redirecting high-momentum flow toward the mirror wake region. Leading edge separation from the guide vane is reduced or eliminated by means of an alternating current -dielectric barrier discharge (AC-DBD) plasma actuator. Particle image velocimetry (PIV) measurements are performed at a range of velocities from 15 to 25 m/s and from windward to leeward angles from -5deg to 5deg. Time-averaged velocity fields are obtained at the center of the mirror for three scenarios: (a) reference case lacking any control elements, (b) guide vane only, and (c) combination of the guide vane and the AC-DBD plasma actuator. The comparison of cases demonstrates that at 25 m/s windward conditions (-5deg) the guide vane is capable of recovering 17% momentum with respect to the reference case. No significant change is observed by activating the AC-DBD plasma actuator. In contrast, at leeward conditions (5deg), the guide vane results in a −20% momentum loss that is rectified to a 6% recovery with actuation. The above implies that for a truck with two mirrors, 23% of momentum may be recovered.

Experimental Characterization of a Micro-Blower for Flow Control

2019 ◽  
Author(s):  
Maria Wu ◽  
Pierre Sullivan
Keyword(s):  
Flow Control ◽  
Turbulent Jets ◽  
Synthetic Jet ◽  
Experimental Characterization ◽  
Continuous Mode ◽  
Mean Velocity ◽  
Burst Mode ◽  
Synthetic Jet Actuator ◽  
Image Velocimetry

Abstract A compact, lightweight, low-power piezoelectric micro-blower was characterized using particle image velocimetry to determine its flow control potential. The micro-blower has been operated in continuous mode as well as in burst mode using two different actuation frequencies. The maximum mean velocity measured with the micro-blower operating in continuous mode was approximately Ūmax = 13 m/s which occurred at the centerline at an approximate stream-wise location of x/d = 4. The velocity profiles in the developed region resemble those of turbulent jets. The momentum-flux from the micro-blower in continuous mode was significantly greater than a typical synthetic jet actuator which was successfully used for flow control, indicating that the micro-blower can impart the necessary momentum to be effective for flow control. With burst mode, the results show that the micro-blower could impart an even greater momentum.

Optimization and Evaluation of Multiple DBD Plasma Actuators Applied in the Tip Leakage Control for Turbine Cascade

2019 ◽  
Author(s):  
Jianyang Yu ◽  
Wenchun Bao ◽  
Fu Chen ◽  
Yanping Song ◽  
Cong Wang
Keyword(s):  
Flow Control ◽  
Mass Flow ◽  
Suction Side ◽  
Plasma Actuator ◽  
Plasma Actuators ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Dbd Plasma ◽  
Tip Leakage ◽  
Leakage Control

Abstract The dielectric barrier discharge (DBD) plasma actuator, in which electrodes are asymmetric arranged, has already demonstrated its ability in flow control. In the present work, the configuration of multiple plasma actuators is placed at the suction side of the cascade top to realize the tip leakage control. However, massive configurations appear when the number of plasma actuators increases, resulting in the investigation of actuator configuration for tip leakage flow control becomes a challenge. The surrogate modelling approach provides a cheap and efficient method to investigate the effect of multiple plasma actuators on the tip leakage flow control. By constructing an approximation model, tip leakage mass flow rates of all configuration are obtained in the present work. What’s more, the flow structures in the tip clearance controlled by the plasma actuators are explained in the process of topological analysis. The results show that the tip leakage mass flow rate is decreasing with the number of active plasma actuators increasing. However, the decreasing would reach its limits in the process of adding plasma actuators. In the analysis of flow topology, single actuator would generate a small vortex at the suction side to cause an obstacle in the tip leakage flow. While the continuous arrangements of plasma actuator is beneficial to generate an induced vortex to diminish the tip leakage flow.

Sign in / Sign up

Export Citation Format

Share Document