scholarly journals Flight Testing an Iced Business Jet for Flight Simulation Model Validation

2007 ◽  
Author(s):  
Thomas Ratvasky ◽  
Billy Barnhart ◽  
Sam Lee ◽  
Jon Cooper
Keyword(s):  
Simulation Model ◽  
Model Validation ◽  
Flight Simulation ◽  
Flight Testing ◽  
Business Jet

A Flight Simulation Vision for Aeropropulsion Altitude Ground Test Facilities

2005 ◽  
Vol 127 (1) ◽  
pp. 8-17 ◽  
Author(s):  
Milt Davis ◽  
Peter Montgomery
Keyword(s):  
System Performance ◽  
Engine Performance ◽  
Aircraft Engine ◽  
Flight Simulation ◽  
Propulsion System ◽  
Test Facility ◽  
Flight Testing ◽  
Test Environment ◽  
Ground Test ◽  
Aircraft System

Testing of a gas turbine engine for aircraft propulsion applications may be conducted in the actual aircraft or in a ground-test environment. Ground test facilities simulate flight conditions by providing airflow at pressures and temperatures experienced during flight. Flight-testing of the full aircraft system provides the best means of obtaining the exact environment that the propulsion system must operate in but must deal with limitations in the amount and type of instrumentation that can be put on-board the aircraft. Due to this limitation, engine performance may not be fully characterized. On the other hand, ground-test simulation provides the ability to enhance the instrumentation set such that engine performance can be fully quantified. However, the current ground-test methodology only simulates the flight environment thus placing limitations on obtaining system performance in the real environment. Generally, a combination of ground and flight tests is necessary to quantify the propulsion system performance over the entire envelop of aircraft operation. To alleviate some of the dependence on flight-testing to obtain engine performance during maneuvers or transients that are not currently done during ground testing, a planned enhancement to ground-test facilities was investigated and reported in this paper that will allow certain categories of flight maneuvers to be conducted. Ground-test facility performance is simulated via a numerical model that duplicates the current facility capabilities and with proper modifications represents planned improvements that allow certain aircraft maneuvers. The vision presented in this paper includes using an aircraft simulator that uses pilot inputs to maneuver the aircraft engine. The aircraft simulator then drives the facility to provide the correct engine environmental conditions represented by the flight maneuver.

Rotorcraft Lateral-Directional Oscillations: The Anatomy of a Nuisance Mode

2021 ◽  
Author(s):  
Dheeraj Agarwal ◽  
Linghai Lu ◽  
Gareth D. Padfield ◽  
Mark D. White ◽  
Neil Cameron
Keyword(s):  
Simulation Model ◽  
Simulation Models ◽  
Flight Test ◽  
Flight Simulation ◽  
Stability And Control ◽  
Systems Research ◽  
Control Derivatives ◽  
Research Aircraft ◽  
Level Of Understanding ◽  
And Control

High-fidelity rotorcraft flight simulation relies on the availability of a quality flight model that further demands a good level of understanding of the complexities arising from aerodynamic couplings and interference effects. One such example is the difficulty in the prediction of the characteristics of the rotorcraft lateral-directional oscillation (LDO) mode in simulation. Achieving an acceptable level of the damping of this mode is a design challenge requiring simulation models with sufficient fidelity that reveal sources of destabilizing effects. This paper is focused on using System Identification to highlight such fidelity issues using Liverpool's FLIGHTLAB Bell 412 simulation model and in-flight LDO measurements from the bare airframe National Research Council's (Canada) Advanced Systems Research Aircraft. The simulation model was renovated to improve the fidelity of the model. The results show a close match between the identified models and flight test for the LDO mode frequency and damping. Comparison of identified stability and control derivatives with those predicted by the simulation model highlight areas of good and poor fidelity.

Development of a Simulation Model for Optimization of Business Process

2018 ◽  
pp. 26-42
Keyword(s):  
Simulation Model ◽  
Model Validation ◽  
Business Process ◽  
Research Question ◽  
Future Research ◽  
The Novel ◽  
Model Based ◽  
Model Validity ◽  
Proposed Model ◽  
New Research

Optimization of business process assists in efficient organization of business process. For the success of optimization of business process, a simulation model based on gap processes for the analysis of buyers' burstiness in business process has been proposed. However, the model has to be validated. The aim of the research is to implement a validation approach to the simulation model based on gap processes for the optimization of business process underpinning elaboration of a new research question on the model validity. The meaning of the key concepts of “validation,” “model validation,” and “model validation approach” is studied. The results of the present research show that the application of real system measurements validates the simulation model for the optimization of business process. The novel contribution of the manuscript is revealed in the newly created research question on the proposed model validity. Directions of future research are proposed.

Transmission-Distribution Co-Simulation: Model Validation with Standalone Simulation

2018 ◽  
Author(s):  
Yaswanth Nag Velaga ◽  
Aoxia Chen ◽  
P.K. Sen ◽  
Gayathri Krishnamoorthy ◽  
Anamika Dubey
Keyword(s):  
Simulation Model ◽  
Model Validation

A Flight Simulation Vision for Aeropropulsion Altitude Ground Test Facilities

2002 ◽  
Author(s):  
Milt Davis ◽  
Peter Montgomery
Keyword(s):  
System Performance ◽  
Engine Performance ◽  
Aircraft Engine ◽  
Flight Simulation ◽  
Propulsion System ◽  
Test Facility ◽  
Flight Testing ◽  
Test Environment ◽  
Ground Test ◽  
Aircraft System

Testing of a gas turbine engine for aircraft propulsion applications may be conducted in the actual aircraft or in a ground-test environment. Ground test facilities simulate flight conditions by providing airflow at pressures and temperatures experienced during flight. Flight-testing of the full aircraft system provides the best means of obtaining the exact environment that the propulsion system must operate in but must deal with limitations in the amount and type of instrumentation that can be put on-board the aircraft. Due to this limitation, engine performance may not be fully characterized. On the other hand, ground-test simulation provides the ability to enhance the instrumentation set such that engine performance can be fully quantified. However, the current ground-test methodology only simulates the flight environment thus placing limitations on obtaining system performance in the real environment. Generally, a combination of ground and flight tests is necessary to quantify the propulsion system performance over the entire envelop of aircraft operation. To alleviate some of the dependence on flight-testing to obtain engine performance during maneuvers or transients that are not currently done during ground testing, a planned enhancement to ground-test facilities was investigated and reported in this paper that will allow certain categories of flight maneuvers to be conducted. Ground-test facility performance is simulated via a numerical model that duplicates the current facility capabilities and with proper modifications represents planned improvements that allow certain aircraft maneuvers. The vision presented in this paper includes using an aircraft simulator that uses pilot inputs to maneuver the aircraft engine. The aircraft simulator then drives the facility to provide the correct engine environmental conditions represented by the flight maneuver.

Sign in / Sign up

Export Citation Format

Share Document