The Analysis of High-Speed Printing Machine Using Fluid-Structure Interaction Method

2007 ◽  
Author(s):  
Jin-Ho Kim ◽  
Jae-Woo Lee ◽  
Soo Hyung Park ◽  
Do-Young Byun ◽  
Yung-Hwan Byun ◽  
...  
Keyword(s):  
High Speed ◽  
Fluid Structure Interaction ◽  
Interaction Method ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Printing Machine

scholarly journals FSI(Fluid-Structure Interaction) Analysis for Harmonious Operation of High-Speed Printing Machine

2008 ◽  
Vol 9 (1) ◽  
pp. 137-146 ◽  
Author(s):  
Jin-Ho Kim ◽  
Jae-Woo Lee ◽  
Soo-Hyung Park ◽  
Do-Young Byun ◽  
Yung-Hwan Byun ◽  
...  
Keyword(s):  
High Speed ◽  
Interaction Analysis ◽  
Fluid Structure Interaction ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Printing Machine

Thermo-Fluid-Dynamic Design of Reciprocating Compressor Cylinders by Fluid Structure Interaction (FSI)

2011 ◽  
Author(s):  
Riccardo Traversari ◽  
Alessandro Rossi ◽  
Marco Faretra
Keyword(s):  
High Speed ◽  
Fluid Dynamic ◽  
Fluid Structure Interaction ◽  
Classical Equation ◽  
Flow Coefficient ◽  
Reciprocating Compressor ◽  
Complex Situation ◽  
Fluid Structure ◽  
Associated Gas ◽  
Structure Interaction

Pressure losses at the cylinder valves of reciprocating compressors are generally calculated by the classical equation of the flow through an orifice, with flow coefficient determined in steady conditions. Rotational speed has increased in the last decade to reduce compressor physical dimensions, weight and cost. Cylinder valves and associated gas passages became then more and more critical, as they determine specific consumption and throughput. An advanced approach, based on the new Fluid Structure Interaction (FSI) software, which allows to deal simultaneously with thermodynamic, motion and deformation phenomena, was utilized to simulate the complex situation that occurs in a reciprocating compressor cylinder during the motion of the piston. In particular, the pressure loss through valves, ducts and manifolds was investigated. A 3D CFD Model, simulating a cylinder with suction and discharge valves, was developed and experimentally validated. The analysis was performed in transient and turbulent condition, with compressible fluid, utilizing a deformable mesh. The 3D domain simulating the compression chamber was considered variable with the law of motion of the piston and the valve rings mobile according to the fluid dynamic forces acting on them. This procedure is particularly useful for an accurate valve loss evaluation in case of high speed compressors and heavy gases. Also very high pressure cylinders, including LDPE applications, where the ducts are very small and MW close to the water one, can benefit from the new method.

scholarly journals Fluid–structure interaction analysis of fluid pressure pulsation and structural vibration features in a vertical axial pump

2019 ◽  
Vol 11 (3) ◽  
pp. 168781401982858
Author(s):  
Liaojun Zhang ◽  
Shuo Wang ◽  
Guojiang Yin ◽  
Chaonian Guan
Keyword(s):  
Pressure Pulsation ◽  
Interaction Analysis ◽  
Equivalent Stress ◽  
Fluid Structure Interaction ◽  
Fluid Pressure ◽  
Structural Vibration ◽  
Interaction Method ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Axial Pump

Current studies on the operation of the axial pump mainly focus on hydraulic performances, while the coupled interaction between the fluid and structure attracts little attention. This study aims to provide numerical investigation into the vibration features in a vertical axial pump based on two-way iterative fluid–structure interaction method. Three-dimensional coupling model was established with high-quality structured grids of ADINA software. Turbulent flow features were studied under design condition, using shear–stress transport k-ω turbulence model and sliding mesh approach. Typical measure points along and perpendicular to flow direction in fluid domain were selected to analyze pressure pulsation features of the impeller and fixed guide vane. By contrast, vibration features of equivalent stress in corresponding structural positions were investigated and compared based on fluid–structure interaction method. In order to explore fluid–structure interaction vibration mechanism, distribution of main frequencies and amplitudes of the measure points was presented based on the Fast Fourier Transformation method. The results reveal the time and frequency law of fluid pressure pulsation and structural vibration at the same position in the vertical axial pump while additionally provide important theoretical guidance for optimization design and safe operation of the vertical axial pump.

Study of adaptive blades in extreme environment using fluid–structure interaction method

2019 ◽  
Vol 91 ◽  
pp. 102734 ◽  
Author(s):  
Weipao Miao ◽  
Chun Li ◽  
Yuanbo Wang ◽  
Bin Xiang ◽  
Qingsong Liu ◽  
...  
Keyword(s):  
Fluid Structure Interaction ◽  
Extreme Environment ◽  
Interaction Method ◽  
Fluid Structure ◽  
Structure Interaction
Sign in / Sign up

Export Citation Format

Share Document