Influence of Moving End-wall on Tip Clearance Flow in Axial Compressor Cascades

2006 ◽  
Author(s):  
Yanhui Wu ◽  
Wuli Chu
Keyword(s):  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
End Wall

A Study of Large Tip Clearance Flows in an Axial Compressor Blade Row

2006 ◽  
Author(s):  
Richard Williams ◽  
David Gregory-Smith ◽  
Li He
Keyword(s):  
Research Work ◽  
Axial Compressor ◽  
Axial Direction ◽  
Low Pressure ◽  
Tip Clearance ◽  
Computational Method ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
End Wall ◽  
Stagger Angle

The tip clearance flow of industrial axial compressor rotors has a significant impact on compressor performance. Most tip clearance flow research work has been undertaken in the earlier low-pressure transonic stages of compressors. The main differences between the earlier (low-pressure) and later (high-pressure) stages include blade profile, stagger angle, Mach number, blade length and tip clearance. The tip clearance in the later stages of an industrial axial compressor is relatively large due to mechanical constraints and short blading. The stagger angle is much lower and so the tip clearance flow is at a higher angle to the (negative) axial direction. In the present work, a computational method has been employed to investigate tip clearance flow from 1% span to 10% span for blading such as that found in the later stages. A pinch tip model is used to model the blade tip in a cascade with a stationary and moving end-wall. It has been found that the tip clearance flow rolls up into a vortex much later than in the earlier stages. The migration of the tip clearance vortex across the passage is much less than for the earlier stages and also the induced vortex is much weaker. Comparisons between a cascade with fixed and moving end-walls are made, the main difference being that the tip clearance flow is stronger with a moving end-wall. The 1% tip clearance flow structure with stationary end-wall is shown to be different from all other cases investigated.

scholarly journals The Inner Workings of Axial Casing Grooves in a One and a Half Stage Axial Compressor With a Large Rotor Tip Gap: Changes in Stall Margin and Efficiency

2018 ◽  
Author(s):  
Chunill Hah
Keyword(s):  
Boundary Layer ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Rates ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Flow Boundary ◽  
Clearance Flow ◽  
Large Rotor

Effects of axial casing grooves (ACGs) on the stall margin and efficiency of a one and a half stage low-speed axial compressor with a large rotor tip gap are investigated in detail. The primary focus of the current paper is to identify the flow mechanisms behind the changes in stall margin and on the efficiency of the compressor stage with a large rotor tip gap. Semicircular axial grooves installed in the rotor’s leading edge area are investigated. A large eddy simulation (LES) is applied to calculate the unsteady flow field in a compressor stage with ACGs. The calculated flow fields are first validated with previously reported flow visualizations and stereo PIV (SPIV) measurements. An in-depth examination of the calculated flow field indicates that the primary mechanism of the ACG is the prevention of full tip leakage vortex (TLV) formation when the rotor blade passes under the axial grooves periodically. The TLV is formed when the incoming main flow boundary layer collides with the tip clearance flow boundary layer coming from the opposite direction near the casing and rolls up around the rotor tip vortex. When the rotor passes directly under the axial groove, the tip clearance flow boundary layer on the casing moves into the ACGs and no roll-up of the incoming main flow boundary layer can occur. Consequently, the full TLV is not formed periodically as the rotor passes under the open casing of the axial grooves. Axial grooves prevent the formation of the full TLV. This periodic prevention of the full TLV generation is the main mechanism explaining how the ACGs extend the compressor stall margin by reducing the total blockage near the rotor tip area. Flows coming out from the front of the grooves affect the overall performance as it increases the flow incidence near the leading edge and the blade loading with the current ACGs. The primary flow mechanism of the ACGs is periodic prevention of the full TLV formation. Lower efficiency and reduced pressure rise at higher flow rates for the current casing groove configuration are due to additional mixing between the main passage flow and the flow from the grooves. At higher flow rates, blockage generation due to this additional mixing is larger than any removal of the flow blockage by the grooves. Furthermore, stronger double-leakage tip clearance flow is generated with this additional mixing with the ACGs at a higher flow rate than that of the smooth wall.

Effect of tip clearance size on the performance of a low-reaction transonic axial compressor rotor

2019 ◽  
Vol 234 (2) ◽  
pp. 127-142
Author(s):  
Wei Zhu ◽  
Songtao Wang ◽  
Longxin Zhang ◽  
Jun Ding ◽  
Zhongqi Wang
Keyword(s):  
Numerical Simulations ◽  
Dynamic Balance ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Phenomena

This study aimed to enhance the understanding of flow phenomena in low-reaction aspirated compressors. Three-dimensional, multi-passage steady and unsteady numerical simulations are performed to investigate the performance sensitivity to tip clearance variation on the first-stage rotor of a multistage low-reaction aspirated compressor. Three kinds of tip clearance sizes including 1.0τ, 2.0τ and 3.0τ are modeled, in which 1.0τ corresponds to the designed tip clearance size of 0.2 mm. The steady numerical simulations show that the overall performance of the rotor moves toward lower mass flow rate when the tip clearance size is increased. Moreover, energy losses, efficiency reduction and stall margin decrease are also observed with increasing tip clearance size. This can be mostly attributed to the damaging impact of intense tip clearance flow. For unsteady simulation, the result shows periodical oscillation of the tip leakage vortex and a “two-passage periodic structure” in the tip region at the near-stall point. The occurrence of the periodical oscillation is due to the severe interaction between the tip clearance flow and the shock wave. However, the rotor operating state is still stable at this working point because a dynamic balance is established between the tip clearance flow and incoming flow.

Investigation of Unsteady Flow Field in a Low-Speed One and a Half Stage Axial Compressor: Effects of Tip Gap Size on the Tip Clearance Flow Structure at Near Stall Operation

2014 ◽  
Author(s):  
Chunill Hah ◽  
Michael Hathaway ◽  
Joseph Katz
Keyword(s):  
Unsteady Flow ◽  
Flow Structure ◽  
Flow Instability ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Clearance Flow ◽  
Tip Clearance Vortex

The primary focus of this paper is to investigate the effect of rotor tip gap size on how the rotor unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor at near stall operation (for example, where maximum pressure rise is obtained). A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at this flow condition with both a small and a large tip gaps. The numerically obtained flow fields at the small clearance matches fairly well with the available initial measurements obtained at the Johns Hopkins University with 3-D unsteady PIV in an index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. The numerical results are also compared with previously published measurements in a low speed single stage compressor (Maerz et al. [2002]). The current study shows that, with the smaller rotor tip gap, the tip clearance vortex moves to the leading edge plane at near stall operating condition, creating a nearly circumferentially aligned vortex that persists around the entire rotor. On the other hand, with a large tip gap, the clearance vortex stays inside the blade passage at near stall operation. With the large tip gap, flow instability and related large pressure fluctuation at the leading edge are observed in this one and a half stage compressor. Detailed examination of the unsteady flow structure in this compressor stage reveals that the flow instability is due to shed vortices near the leading edge, and not due to a three-dimensional separation vortex originating from the suction side of the blade, which is commonly referred to during a spike-type stall inception. The entire tip clearance flow is highly unsteady. Many vortex structures in the tip clearance flow, including the sheet vortex system near the casing, interact with each other. The core tip clearance vortex, which is formed with the rotor tip gap flows near the leading edge, is also highly unsteady or intermittent due to pressure oscillations near the leading edge and varies from passage to passage. For the current compressor stage, the evidence does not seem to support that a classical vortex breakup occurs in any organized way, even with the large tip gap. Although wakes from the IGV influence the tip clearance flow in the rotor, the major characteristics of rotor tip clearance flows in isolated or single stage rotors are observed in this one and a half stage axial compressor.

Leakage Effects in the Rotor Tip-Clearance Region of a Multistage Axial Compressor: Part 2 — Numerical Modelling

1998 ◽  
Author(s):  
E. S. Politis ◽  
K. C. Giannakoglou ◽  
K. D. Papailiou
Keyword(s):  
Axial Compressor ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Computational Domain ◽  
Loose Coupling ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Flow Effects ◽  
Multistage Axial Compressor ◽  
Asme Paper

Innovative measurements of tip-clearance flow for the 3rd stage rotor embedded in a four stage Low-Speed Research Compressor are presented in the companion ASME paper. Here, in Part 2, the rotor flow is numerically simulated through a Navier-Stokes solver implementing the k-ε turbulence model. The 3rd stage rows are considered as discrete parts of the same computational domain and the flow in each one of them is treated as steady in the corresponding system of reference. An iterative, though loose, coupling between the rotor exit and the stator inlet is established by artificially increasing the inter-row distance. To model tip-clearance flow effects with sufficient accuracy, a two-block grid system per row is used. Comparisons with measurements published in Part 1 for the average flow quantities at the exit of both rows are presented. Row patterns close to the rotor tip-clearance region are illustrated.

Numerical Investigation of Relation Between Unsteady Behavior of Tip Leakage Vortex and Rotating Disturbance in a Transonic Axial Compressor Rotor

2008 ◽  
Author(s):  
K. Yamada ◽  
K. Funazaki ◽  
H. Sasaki
Keyword(s):  
Vortex Breakdown ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Rotating Instability

The purpose of this study is to have a better understanding of the unsteady behavior of tip clearance flow at near-stall condition from a multi-passage simulation and to clarify the relation between such unsteadiness and rotating disturbance. This study is motivated by the following concern. A single passage simulation has revealed the occurrence of the tip leakage vortex breakdown at near-stall condition in a transonic axial compressor rotor, leading to the unsteadiness of the tip clearance flow field in the rotor passage. These unsteady flow phenomena were similar to those in the rotating instability, which is classified in one of the rotating disturbances. In other words it is possible that the tip leakage vortex breakdown produces a rotating disturbance such as the rotating instability. Three-dimensional unsteady RANS calculation was conducted to simulate the rotating disturbance in a transonic axial compressor rotor (NASA Rotor 37). The four-passage simulation was performed so as to capture a short length scale disturbance like the rotating instability and the spike-type stall inception. The simulation demonstrated that the unsteadiness of tip leakage vortex, which was derived from the vortex breakdown at near-stall condition, invoked the rotating disturbance in the rotor, which is similar to the rotating instability.

Vortex Dynamics and Mechanisms for Viscous Losses in the Tip-Clearance Flow

2005 ◽  
Author(s):  
Donghyun You ◽  
Meng Wang ◽  
Parviz Moin ◽  
Rajat Mittal
Keyword(s):  
Tip Clearance ◽  
Wall Region ◽  
Mean Flow ◽  
Mean Velocity ◽  
Tip Leakage Vortex ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Viscous Losses ◽  
Clearance Flow ◽  
End Wall

The tip-clearance flow in axial turbomachines is studied using large-eddy simulation with particular emphasis on understanding the underlying mechanisms for viscous losses in the end-wall region and the unsteady characteristics of the tip-leakage vortical structures. Systematic and detailed analysis of the mean flow field and turbulence statistics has been made in a linear cascade with a moving end-wall. The tip-leakage jet and tip-leakage vortex are found to produce significant mean velocity gradients, leading to the production of vorticity and turbulent kinetic energy. These are the major causes for viscous losses in the cascade end-wall region. An analysis of the energy spectra and space-time correlations of the velocity fluctuations suggests that the tip-leakage vortex is subject to a pitchwise low frequency wandering motion.

A Comparison Between the Design Point and Near-Stall Performance of an Axial Compressor

1990 ◽  
Vol 112 (1) ◽  
pp. 109-115 ◽  
Author(s):  
N. M. McDougall
Keyword(s):  
Rotor Blade ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Design Point ◽  
Blade Row ◽  
Clearance Flow ◽  
Stator Blade

Detailed measurements have been made within an axial compressor operating both at design point and near stall. Rotor tip clearance was found to control the performance of the machine by influencing the flow within the rotor blade passages. This was not found to be the case in the stator blade row, where hub clearance was introduced beneath the blade tips. Although the passage flow was observed to be altered dramatically, no significant changes were apparent in the overall pressure rise or stall point. Small tip clearances in the rotor blade row resulted in the formation of corner separations at the hub, where the blade loading was highest. More representative clearances resulted in blockage at the tip due to the increased tip clearance flow. The effects that have been observed emphasize both the three-dimensional nature of the flow within compressor blade passages, and the importance of the flow in the endwall regions in determining the overall compressor performance.

Unsteady tip clearance flow pattern in an isolated axial compressor rotor with micro tip injection

2007 ◽  
Vol 16 (4) ◽  
pp. 309-320 ◽  
Author(s):  
Shaojuan Geng ◽  
Hongwu Zhang ◽  
Jingyi Chen ◽  
Weiguang Huang
Keyword(s):  
Flow Pattern ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Tip Injection
Sign in / Sign up

Export Citation Format

Share Document