The Safety and Delay Device for the LFK-NG Double-Pulse Motor Demonstrator

2006 ◽  
Author(s):  
Andreas Hacker ◽  
Rudolf Stingl ◽  
Helmut Niedermaier ◽  
K. Naumann
Keyword(s):  
Double Pulse

Chromium thin film ablation with double pulse of femtosecond laser

2004 ◽  
Author(s):  
Etsuji Ohmura ◽  
Tomohiro Okamoto ◽  
Seiji Fujiwara ◽  
Tomokazu Sano ◽  
Isamu Miyamoto
Keyword(s):  
Thin Film ◽  
Femtosecond Laser ◽  
Double Pulse

scholarly journals A Novel Gate Drive Circuit for Suppressing Turn-on Oscillation of Non-Kelvin Packaged SiC MOSFET

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2449
Author(s):  
Hongyan Zhao ◽  
Jiangui Chen ◽  
Yan Li ◽  
Fei Lin
Keyword(s):  
Thermal Conductivity ◽  
Breakdown Voltage ◽  
Basic Principle ◽  
Double Pulse ◽  
Experimental Results ◽  
Switching Frequency ◽  
Turn On ◽  
Proof Testing ◽  
Gate Driver ◽  
Drive Circuit

Compared with a silicon MOSFET device, the SiC MOSFET has many benefits, such as higher breakdown voltage, faster action speed and better thermal conductivity. These advantages enable the SiC MOSFET to operate at higher switching frequencies, while, as the switching frequency increases, the turn-on loss accounts for most of the loss. This characteristic severely limits the applications of the SiC MOSFET at higher switching frequencies. Accordingly, an SRD-type drive circuit for a SiC MOSFET is proposed in this paper. The proposed SRD-type drive circuit can suppress the turn-on oscillation of a non-Kelvin packaged SiC MOSFET to ensure that the SiC MOSFET can work at a faster turn-on speed with a lower turn-on loss. In this paper, the basic principle of the proposed SRD-type drive circuit is analyzed, and a double pulse platform is established. For the purpose of proof-testing the performance of the presented SRD-type drive circuit, comparisons and experimental verifications between the traditional gate driver and the proposed SRD-type drive circuit were conducted. Our experimental results finally demonstrate the feasibility and effectiveness of the proposed SRD-type drive circuit.

scholarly journals Influence of Duty Ratio and Current Mode on Robot 316L Stainless Steel Arc Additive Manufacturing

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 508
Author(s):  
Ping Yao ◽  
Hongyan Lin ◽  
Wei Wu ◽  
Heqing Tang
Keyword(s):  
Stainless Steel ◽  
Additive Manufacturing ◽  
Heat Input ◽  
Low Frequency ◽  
Single Pulse ◽  
Pulse Mode ◽  
Double Pulse ◽  
Duty Ratio ◽  
Utilization Rate ◽  
Specimen Height

Wire and arc additive manufacturing (WAAM) is usually for fabricating components due to its low equipment cost, high material utilization rate and cladding efficiency. However, its applications are limited by the large heat input decided by process parameters. Here, four 50-layer stainless steel parts with double-pulse and single-pulse metal inert gas (MIG) welding modes were deposited, and the effect of different duty ratios and current modes on morphology, microstructure, and performance was analyzed. The results demonstrate that the low frequency of the double-pulse had the effect of stirring the molten pool; therefore, the double-pulse mode parts presented a bigger width and smaller height, finer microstructure and better properties than the single-pulse mode. Furthermore, increasing the duty ratio from 35% to 65% enlarged the heat input, which then decreased the specimen height, increased the width, and decreased the hardness and the tensile strength.

Double-pulse femtosecond laser peening of aluminum alloy AA5038: Effect of inter-pulse delay on transient optical plume emission and final surface micro-hardness

2016 ◽  
Vol 109 (21) ◽  
pp. 211902 ◽  
Author(s):  
E. I. Ageev ◽  
V. Yu. Bychenkov ◽  
A. A. Ionin ◽  
S. I. Kudryashov ◽  
A. A. Petrov ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Femtosecond Laser ◽  
Double Pulse ◽  
Laser Peening ◽  
Micro Hardness ◽  
Pulse Delay ◽  
Final Surface ◽  
Plume Emission
Sign in / Sign up

Export Citation Format

Share Document