Parameterization of Boundary Layer Control Dimples on a Low Pressure Turbine Blade

2004 ◽  
Author(s):  
John Casey ◽  
Paul King ◽  
Rolf Sondergaard
Keyword(s):  
Boundary Layer ◽  
Turbine Blade ◽  
Low Pressure ◽  
Boundary Layer Control ◽  
Low Pressure Turbine ◽  
Layer Control

Numerical Investigation of Contrasting Flow Physics in Different Zones of a High-Lift Low-Pressure Turbine Blade

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Jiahuan Cui ◽  
V. Nagabhushana Rao ◽  
Paul Tucker
Keyword(s):  
Boundary Layer ◽  
Turbine Blade ◽  
Low Pressure ◽  
The State ◽  
Suction Surface ◽  
Flow Physics ◽  
Pressure Surface ◽  
Low Pressure Turbine ◽  
Flow Features ◽  
The Impact

Using a range of high-fidelity large eddy simulations (LES), the contrasting flow physics on the suction surface, pressure surface, and endwalls of a low-pressure turbine (LPT) blade (T106A) was studied. The current paper attempts to provide an improved understanding of the flow physics over these three zones under the influence of different inflow boundary conditions. These include: (a) the effect of wakes at low and high turbulence intensity on the flow at midspan and (b) the impact of the state of the incoming boundary layer on endwall flow features. On the suction surface, the pressure fluctuations on the aft portion significantly reduced at high freestream turbulence (FST). The instantaneous flow features revealed that this reduction at high FST (HF) is due to the dominance of “streak-based” transition over the “Kelvin–Helmholtz” (KH) based transition. Also, the transition mechanisms observed over the turbine blade were largely similar to those on a flat plate subjected to pressure gradients. On pressure surface, elongated vortices were observed at low FST (LF). The possibility of the coexistence of both the Görtler instability and the severe straining of the wakes in the formation of these elongated vortices was suggested. While this was true for the cases under low turbulence levels, the elongated vortices vanished at higher levels of background turbulence. At endwalls, the effect of the state of the incoming boundary layer on flow features has been demonstrated. The loss cores corresponding to the passage vortex and trailing shed vortex were moved farther from the endwall with a turbulent boundary layer (TBL) when compared to an incoming laminar boundary layer (LBL). Multiple horse-shoe vortices, which constantly moved toward the leading edge due to a low-frequency unstable mechanism, were captured.

scholarly journals Intermittent Behavior of the Separated Boundary Layer Along the Suction Surface of a Low Pressure Turbine Blade Under Periodic Unsteady Flow Conditions

2005 ◽  
Author(s):  
B. O¨ztu¨rk ◽  
M. T. Schobeiri ◽  
David E. Ashpis
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Turbine Blade ◽  
Low Pressure ◽  
Boundary Layer Transition ◽  
Wake Flow ◽  
Unsteady Boundary Layer ◽  
Flow Conditions ◽  
Suction Surface ◽  
Low Pressure Turbine

The paper experimentally and theoretically studies the effects of periodic unsteady wake flow and aerodynamic characteristics on boundary layer development, separation and re-attachment along the suction surface of a low pressure turbine blade. The experiments were carried out at Reynolds number of 110,000 (based on suction surface length and exit velocity). For one steady and two different unsteady inlet flow conditions with the corresponding passing frequencies, intermittency behavior were experimentally and theoretically investigated. The current investigation attempts to extend the intermittency unsteady boundary layer transition model developed in previously to the LPT cases, where separation occurs on the suction surface at a low Reynolds number. The results of the unsteady boundary layer measurements and the intermittency analysis were presented in the ensemble-averaged, and contour plot forms. The analysis of the boundary layer experimental data with the flow separation, confirms the universal character of the relative intermittency function which is described by a Gausssian function.

A Low Reynolds Number Experimental Evaluation of Tubercles on a Low-Pressure Turbine Cascade

2019 ◽  
Author(s):  
Stephen A. Pym ◽  
Asad Asghar ◽  
William D. E. Allan ◽  
John P. Clark
Keyword(s):  
Boundary Layer ◽  
Turbine Blade ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Blade Profile ◽  
Suction Surface ◽  
Low Reynolds Numbers ◽  
Low Pressure Turbine ◽  
Low Reynolds ◽  
Highly Loaded

Abstract Aircraft are operating at increasingly high-altitudes, where decreased air density and engine power settings have led to increasingly low Reynolds numbers in the low-pressure turbine portion of modern-day aeroengines. These operating conditions, in parallel with highly-loaded blade profiles, result in non-reattaching laminar boundary layer separation along the blade suction surface, increasing loss and decreasing engine performance. This work presents an experimental investigation into the potential for integrated leading-edge tubercles to improve blade performance in this operating regime. A turn-table cascade test-section was constructed and commissioned to test a purpose-designed, forward-loaded, low-pressure turbine blade profile at various incidences and Reynolds numbers. Baseline and tubercled blades were tested at axial chord Reynolds numbers at and between 15 000 and 60 000, and angles of incidence ranging from −5° to +10°. Experimental data collection included blade surface pressure measurements, total pressure loss in the blade wakes, hot-wire anemometry, surface hot-film measurements, and surface flow visualization using tufts. Test results showed that the implementation of tubercles did not lead to a performance enhancement. However, useful conclusions were drawn regarding the ability of tubercles to generate stream-wise vortices at ultra-low Reynolds numbers. Additional observations helped to characterize the suction surface boundary layer over the highly-loaded, low-pressure turbine blade profile when at off-design conditions. Recommendations were made for future work.

The Influence of Mach Number on the Boundary Layer Development of High-Lift Low Pressure Turbine in Low Reynolds Number

2020 ◽  
Author(s):  
Wenhua Duan ◽  
Jian Liu ◽  
Weiyang Qiao
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Mach Number ◽  
Turbine Blade ◽  
Low Reynolds Number ◽  
Low Pressure ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Boundary Layer Development ◽  
Layer Development

Abstract A numerical analysis of the effect of Mach number on the boundary layer development and aerodynamic performance of a high-lift, after loaded low pressure turbine blade is presented in this paper. The turbine blade is designed for the GTF engine and works in a low Reynolds number, high Mach number environment. Three different isentropic exit Mach numbers (0.14, 0.87 and 1.17) are simulated by large eddy simulation method, while the Reynolds number based on the axial chord length of the blade and the exit flow velocity is kept the same (1 × 105). The condition Mais,2 = 0.14 represents the lowspeeed wind tunnel environment which is usually used in the low pressure turbine investigation. The condition Mais,2 = 0.87 represents the design point of the turbine blade. The condition Mais,2 = 1.17 represents the severe environment when the shock wave shows up. A comparison of the boundary layer development is made and the total pressure loss results from the boundary layer is discussed.

Simulation of Transitional Flow on Low Pressure Turbine Blade With Unsteady Downstream Potential Interaction

2013 ◽  
Author(s):  
Can Ma ◽  
Xin Yuan
Keyword(s):  
Boundary Layer ◽  
Turbine Blade ◽  
Potential Field ◽  
Stokes Equations ◽  
Low Pressure ◽  
Experimental Results ◽  
Transitional Flow ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine ◽  
Transitional Boundary Layer

This paper numerically investigates the transitional flow on a LPT (low pressure turbine) blade with fluctuating downstream potential field. A linear T106 cascade is subjected to an oscillating potential field generated by downstream moving bars. Previous experimental results in open literature showed that the unsteady downstream potential field has an obvious influence on the transitional boundary layer of LPT blade. For the numerical simulations in this paper, the unsteady Reynolds-Averaged Navier-Stokes equations are solved using the commercial software FLUENT. The transition model used in this paper is the γ-Reθ model, which has been validated against a number of transitional flows previously, including the influence of upstream wakes on the transitional boundary layer of T106 turbine blade. The simulation results are first compared to the experimental results in open literature to validate the numerical methods. Two different FSTI (free stream turbulence intensity), 1.6% and 4.0% are investigated with axial spacing between the blade and the downstream bar varying from 50% axial chord to 25% axial chord. To investigate the influence of flow compressibility, two different inlet Mach numbers, 0.02 and 0.2 are simulated. Results show that decreasing the axial spacing has an influence on the unsteady boundary layer separation and transition and the influence is enhanced at elevated inlet Mach number.

Sign in / Sign up

Export Citation Format

Share Document